Mercado Medic REAL 9700 Coxit Assembly instructions

REAL 9700 Coxit
Chair designed for those with knee and hip disabilities. Also suitable for those with complete leg prostheses.
1
3
2
4
1
5
4
2
1
2
1
R
The REAL chair has exchangeable components, accessories and functions
and can be adjusted to suit individual needs. The chair should only be used
for that person and for the purpose for which it was originally intended. The
chair is designed for use indoors and should not be exposed to water or other
fluids or chemicals. Nor should it be exposed to high temperatures or long
term intensive sunlight or other such exposure. The chair may not be equipped
with other accessories or components than those approved by Mercado Medic
AB. Repairs and other technical adjustments may only be carried out by
personnel authorised by Mercado Medic AB. Please read through these
instructions carefully before using your chair.
1
INSTRUCTIONS for USE and CARE
Standard ComfortMedic
1
2
Backrest
Armrest
Sitting height
Rotation accessory
4
Articlenr: 087514022-E-9801
January 2003
The armrests can be adjusted up or down and from side to side on the
curve of the armrest. Loosen the knob to adjust the height (1) or the width
(2), and then tighten the knob again.
The height of the seat is adjusted using the lever (1) on one side of the
seat (standard right). Lift the lever to change the height. Note that light
people may need a little assistance to raise and lower their chair.
There are three types of back mechanisms: Standard, Medic and Comfort. The backrest is available in both
a low and a high design (all the chairs illustrated show the high backrest design). All back mechanisms have
separate adjustment controls for height (1) and angle (2). Loosen the knob, adjust to the desired height/angle
and then lock the knob. On the Comfort model with a gas spring device, push the lever forward to change
the angle. On the Medic model the depth can be adjusted by using the knob (3). In the high position the angle
of the backrest itself can be adjusted by using the knob. (4). The Comfort model has a knob (5) for adjusting
the angle of the backrest in both positions.
Chairs equipped with a rotation device can be manoeuvred using the knob.
Turn clockwise to release and anti-clockwise to lock the device. Please
note! Rotation should be in the locked position when you sit down and stand
up from your chair.

1
4
3
2
1
4
Hand brake
Sitting angle
Cleaning and maintenance
1
Adjustment of the coxit flaps
1
2
Handle
Control
Gas spring
There are two methods for adjusting the coxit flaps. On chairs with no seat angling the controls are placed
under the seat (1). Loosen the relevant knob, adjust to the required angle and then tighten the knob. On chairs
equipped with seat angling the controls are placed in the back edge of the seat (2). Turn the knob in a
clockwise direction to lower the flap and in an anti-clockwise direction to raise it. The flap locks
automatically when the knob is released.
2
The brakes are controlled with a lever (1). To lock: push the
lever forward if the chair has a cross frame, back if the chair has
an H frame. The brake lever can be moved to whichever side of
the chair you prefer. If the chair is equipped with an H-frame the
brakes can also be manoeuvred with the foot (2). Please note!
The brakes should always be on when you sit down or raise
yourself from your chair. The brakes should be checked
regularly. The rubber brake blocks can be replaced after wear
and tear. Braking function may be impaired on an uneven
surface.
The angle of the seat is available in two designs: with a gas spring or a handle device. The gas spring control
is situated in the back, left-hand edge of the seat (1) and is adjusted by pushing the lever forward carefully.
The controls may also be placed under one of the armrests (2). The handle control for adjusting the angle of
the seat is adjusted by turning the handle (3). The angle degrees may be adjusted by means of the nuts (4).
The chair should be wiped clean and kept free from dust and grime. The upholstery may be washed with foam
cleaner. The seat, backrest and other upholstered parts are for functional reasons not made of sealed materials.
For reasons of hygiene, the seat base and padding material should always be changed whenever the
upholstery is changed.
The Fixlyftomat automatic device should be checked regularly and kept free of dust and grime. Move the seat
base to the highest position. Clean with a cloth. Do not use water or any cleaning fluids. Lubricate the
cylinder with a thin layer of Teflon or a silicon based lubricant. These are not as messy as mineral based oils.
Any necessary tools, lubricants etc. for maintaining the chair may be ordered from Mercado Medic AB.
Box 1074, 181 22 Lidingö Telefon [phone] Fax [phone] E-post ser[email protected]
Export Office: Nobelweg 22, 3899 BN Zeewolde, The Netherlands, E-mail inf[email protected]
Tel: [phone] Fax [phone]