Mercusys MW300RE User manual

User Guide
300Mbps Wi-Fi Range Extender
MW300RE
REV3.0.1
1910080042

COPYRIGHT & TRADEMARK
Specifications are subject to change without notice. is a
registered trademark of MERCUSYS TECHNOLOGIES CO., LTD. Other brands and product
names are trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make
any derivative such as translation, transformation, or adaptation without permission from
MERCUSYS TECHNOLOGIES CO., LIMITED. Copyright © 2019 MERCUSYS TECHNOLOGIES
CO., LIMITED. All rights reserved.
http://www.mercusys.com

CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
OPERATING FREQUENCY (the maximum transmitted power)
2412MHz—2472MHz(20dBm)
EU declaration of conformity
MERCUSYS hereby declares that the device is in compliance with the essential requirements
and other relevant provisions of directives 2014/53/EU, 2009/125/EC and 2011/65/EU.
The original EU declaration of conformity may be found at http://www.mercusys.com/en/ce.
RF Exposure Information
This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure
of the general public to electromagnetic fields by way of health protection.
The device complies with RF specifications when the device used at 20 cm from your body.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
NCC Notice
注意！
依據低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、
加大功率或變更原設計之特性或功能。

第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即
停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射
頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。
BSMI Notice
安全諮詢及注意事項
•請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
•清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
•注意防潮，請勿將水或其他液體潑灑到本產品上。
•插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
•請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
•請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
限用物質含有情況標示聲明書
產品元件名稱
限用物質及其化學符號
鉛
Pb
鎘
Cd
汞
Hg
六價鉻
CrVI
多溴聯苯
PBB
多溴二苯醚
PBDE
PCB ○○○○○○
外殼 ○○○○○○
電源供應板 −○○○○○
備考
1. "超出 0.1 wt %" 及"超出 0.01 wt %"
系指限用物質之百分比含量超出百分比含
量基準值。
備考
2. "○"系指該項限用物質之百分比含量未超出百分比含量基準值。
備考
3. "
−
" 系指該項限用物質為排除項目。
Safety Information
•Keep the device away from water, fire, humidity or hot environments.
•Do not attempt to disassemble, repair, or modify the device.

•Do not use the device where wireless devices are not allowed.
•The socket-outlet shall be installed near the equipment and shall be easily
accessible.
Please read and follow the above safety information when operating the device. We
cannot guarantee that no accidents or damage will occur due to improper use of
the device. Please use this product with care and operate at your own risk.
Explanation of the symbols on the product label
Symbol
Explanation
Class II equipment
AC voltage
Indoor use only
RECYCLING
T
his product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to be recycled or
dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or
to the retailer when he buys a new electrical or electronic equipment.

CONTENTS
Conventions........................................................................................................................... 1
Chapter 1. Introduction................................................................................................... 2
1.1 Product Overview............................................................................................................................. 2
1.2 Product Appearance....................................................................................................................... 2
1.2.1 LED Explanation.................................................................................................................. 2
1.2.2 Button Explanation ............................................................................................................ 3
Chapter 2. Connect the Extender to the Internet..................................................... 4
2.1 Method One: Via a Web Browser ................................................................................................ 4
2.2 Method Two: Via WPS..................................................................................................................... 7
Chapter 3. Basic Configuration..................................................................................... 8
3.1 Status ................................................................................................................................................... 8
3.2 Device Management ....................................................................................................................... 9
Chapter 4. Advanced Configuration..........................................................................10
4.1 Wireless .............................................................................................................................................10
4.2 Profile .................................................................................................................................................10
4.3 Network..............................................................................................................................................12
4.4 DHCP Server....................................................................................................................................12
4.5 System Tools...................................................................................................................................14
4.5.1 Firmware Upgrade ...........................................................................................................14
4.5.2 Factory Default Restore.................................................................................................15
4.5.3 Backup & Restore.............................................................................................................15
4.5.4 Reboot .................................................................................................................................16
4.5.5 Login Password ................................................................................................................16
4.5.6 System Log ........................................................................................................................16
FAQ (Frequently Asked Questions) ...............................................................................18

MW300RE
300Mbps Wi-Fi Range Extender
Conventions
The extender or MW300RE, or device mentioned in this User Guide stands for MW00RE
Wireless Wi-Fi extender without any explanations.
Parameters provided in the pictures are just references for setting up the product, which may
differ from the actual situation.
You can set the parameters according to your demand.
More Info
Specifications and the latest software can be found at the product page at the official website
http://www.mercusys.com.
The Quick Installation Guide can be found where you find this guide or inside the package of
the extender.
*Maximum wireless signal rates are the physical rates derived from IEEE Standard 802.11
specifications. Actual wireless data throughput and wireless coverage per ft2 are not
guaranteed and will vary as a result of 1) environmental factors, including building materials,
physical objects, and obstacles, 2) network conditions, including local interference, volume
and density of traffic, product location, network complexity, and network overhead, and 3)
client limitations, including rated performance, location, connection quality, and client
condition.
*The maximum extended Wi-Fi coverage specification is based on performance testing results.
Actual Wi-Fi coverage may vary due to environmental factors, including building materials and
wireless interferences.
- 1 -

MW300RE
300Mbps Wi-Fi Range Extender
Chapter 1. Introduction
1.1 Product Overview
The range extender connects to your router wirelessly, strengthening its signal and
expanding its coverage into areas that could not otherwise be reached.
Multicolor LED helps you find the right location for your range extender for the best Wi-Fi
extension.
1.2 Product Appearance
1.2.1 LED Explanation
LED
Status
Indication
Signal
Blinking red
The extender is connecting to the router.
Solid red
The extender is not connected to the router.
Solid green
The extender is connected to the router, and is in a good
location.
Solid orange
The extender is connected to the router, but is too far away
from the router.
- 2 -

MW300RE
300Mbps Wi-Fi Range Extender
1.2.2 Button Explanation
Button
Description
RESET/WPS
Press and hold this button for more than 5 seconds until the
Signal LED starts blinking quickly to reset the extender.
Press for 1 second to use the WPS function.
- 3 -

MW300RE
300Mbps Wi-Fi Range Extender
Chapter 2. Connect the Extender to the Internet
Power On
Plug the extender into a power outlet near your router, and the Signal LED turns solid red.
Note: For safety and best performance, we suggest that you position the extender vertically as
shown below.
2.1 Method One: Via a Web Browser
1. Connect your wireless device to the extender's network MERCUSYS_RE_XXXX.
Note:
1. The default SSID (network name) is printed on the product label at the back of the extender.
2. If you are using a computer, unplug the Ethernet cable from your computer first (if any).
2. Follow the instructions of the Quick Setup Wizard to connect the extender to your router.
1) Launch a web browser and enter http://mwlogin.net in the address field.
- 4 -

MW300RE
300Mbps Wi-Fi Range Extender
2) A login window will appear. Create a login password when prompted, then click Start.
For subsequent logins, use the password you have set.
3) The extender will scan and display all available networks. Select your router's host
network from the list.
Note:
If the network you want to extend is on but not listed, please try the following steps.
· Move the extender closer to your router, and click Rescan in the top-right corner of the list.
· Click Other... to manually enter the SSID (network name) and password of the network you want to
extend, and click Connect.
- 5 -

MW300RE
300Mbps Wi-Fi Range Extender
4) Enter the network password when prompted, then click Connect. You can also
customize the extended network name on this page.
5) Check the Signal LED on your extender. Green or orange LED indicates a successful
connection.
3. Relocate the extender.
1) Plug the extender into an electrical outlet between your host router and the Wi-Fi
“dead“ zone. The location you choose must be within the range of your existing host
network.
2) Wait until the Signal LED is lit and solid green. If it’s not, relocate it closer to the host
router to achieve better signal quality.
- 6 -

MW300RE
300Mbps Wi-Fi Range Extender
4. Enjoy! Connect to the extended network and enjoy the internet. The extended network
uses the same wireless password as your host networks, but may have different network
name if you have customized the SSID during the configuration.
2.2 Method Two: Via WPS
1. Press the WPS button on your router.
2. Within two minutes, press the RESET/WPS button on your extender for 1 second. The
Signal LED should change from flashing to a solid state, indicating a successful WPS
connection.
3. Relocate the extender.
1) Plug the extender into an electrical outlet between your host router and the Wi-Fi
“dead“ zone. The location you choose must be within the range of your existing host
network.
2) Wait until the Signal LED is lit and solid green. If it’s not, relocate it closer to the host
router to achieve better signal quality.
4. Enjoy! Connect to the extended network and enjoy the internet. The extended network
uses the same wireless password as your host networks, but may have different network
name if you have customized the SSID during the configuration.
- 7 -

MW300RE
300Mbps Wi-Fi Range Extender
Chapter 3. Basic Configuration
After your successful login, you will see the basic configuration page. The main menus are on
the left of the page. On the right you can configure the corresponding function.
There are two functions on the Basic page: Status and Device Management. The detailed
explanations for each function are listed below.
3.1 Status
Go to Basic→Status, you can view the internet status of your extender.
•Status - Displays the connection status and the name of the host network.
•Wireless Scanner - Click to find all available networks if you want to extend another
host network.
- 8 -

MW300RE
300Mbps Wi-Fi Range Extender
•Extended SSID - Displays the name of the extended network. You can edit the name
on this page.
•Distance between the extender and the host AP is Good – Displays whether the
extender is in a proper location. If the distance is too far, relocate the extender closer
to your router.
3.2 Device Management
Go to Basic→Device Management, you can view and manage the connected or blocked
devices.
1. Host Devices
•Device Name/IP Address/MAC Address - Displays the name, IP address and MAC
address of the device. You can click to edit the device name.
•Block - Click to remove the device from the list.
2. Blocked Devices
•Device Name -Displays the name of the device. You can click to edit the device
name.
•Allow - Click to remove the device from the list.
- 9 -

MW300RE
300Mbps Wi-Fi Range Extender
Chapter 4. Advanced Configuration
This chapter will show each web page's key functions and the configuration details.
4.1 Wireless
Go to Advanced→Wireless, you can view and configure the extended wireless network
settings.
•Network Name (SSID) - The extended wireless network name. You can change the name
on this page.
•Hide SSID – Select this option if you want to hide the extended network from others.
4.2 Profile
Profile is used for managing the information of connected host networks. You can view
recently connected networks or manually add new ones.
•Operation – Click Connect to connect to the host network in this profile or click Edit to
edit an existing profile.
•Add - Manually add a host AP by entering the extended network name, host network name,
- 10 -

MW300RE
300Mbps Wi-Fi Range Extender
host MAC address, security type and password.
•Delete All - Click to delete all profiles.
•Delete Selected - Click to delete selected profiles.
To add a new profile
1) Click Add.
2) Complete the settings as shown below, and click Save.
•Extended SSID -Enter the extended network name.
•Host SSID - Enter the host network name.
•Host MAC Address - Enter the MAC address of the host router.
•Host AP Security -Select the security type of the host network.
•Host AP Password – Enter the password of the host network.
To connect to a host network
To connect to a host network that is listed in the profile screen, just find the profile and then
click Connect.
To manage an existing profile
To change the settings of an existing profile, find the profile and click Edit, then you can edit
the settings of this profile.
If you want to delete a profile that you no longer use, select the profile and click Delete
Selected.
- 11 -

MW300RE
300Mbps Wi-Fi Range Extender
4.3 Network
Go to Advanced→Network, you can configure network settings of the extender.
•MAC Address - The unique physical address of the extender.
•IP Settings - Select Auto or Manual. It is recommended to select Auto. If you want to set
the IP address and subnet mask manually, select Manual and enter them manually.
•IP Address -The LAN IP address of the extender.
•Subnet Mask -Subnet mask determines the size of the network. Normally it is
255.255.255.0.
4.4 DHCP Server
Go to Advanced→DHCP Server, you can configure the DHCP Server settings. DHCP server
will automatically assign IP address and subnet mask to devices on your network.
- 12 -

MW300RE
300Mbps Wi-Fi Range Extender
•DHCP Server - Select On, Off or Auto. When Auto is selected, the extender will detect
other DHCP server on the network to determine whether to renew IP address, Gateway
and DNS of this DHCP server or not.
•Start IP Address -Specify an IP address for the DHCP Server to start with when
assigning IP addresses. 192.168.1.100 is the default start address.
•End IP Address -Specify an IP address for the DHCP Server to end with when assigning
IP addresses. 192.168.1.199 is the default end address.
•Address Lease Time -The amount of time a network user will be allowed connection to
the extender with their current dynamic IP Address. Enter the amount of time in minutes
and the user will be leased this dynamic IP Address. After the time is up, the user will be
automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880
minutes. The default value is 120 minutes.
•Gateway - (Optional.) The default is 0.0.0.0. Enter the LAN IP address of your host router.
•Primary DNS - (Optional.) Enter the DNS IP address provided by your ISP or consult your
ISP.
•Secondary DNS - (Optional.) Enter the IP address of another DNS server if your ISP
provides two DNS servers.
•Host - The name of the DHCP client.
- 13 -

MW300RE
300Mbps Wi-Fi Range Extender
•MAC Address -The MAC address of the DHCP client
•IP Address -The IP address that has been allocated to the DHCP client
•Effective Time -The time of the DHCP client leased. After the dynamic IP address has
expired, a new dynamic IP address will be automatically assigned to the user.
Click Refresh to show the current attached devices.
4.5 System Tools
4.5.1 Firmware Upgrade
Go to System Tools→Firmware Upgrade, and then you can update the latest version of
firmware for the extender.
•Hardware Version -Displays the current hardware version. The version of the upgrade file
must accord with the extender’s current hardware version.
•Firmware Version -Displays the current firmware version.
To upgrade the extender's firmware, follow the steps below:
Note: To avoid any damage, it is important to keep the extender powered on during the entire process.
1. Download the latest firmware upgrade file from our website (http:// www.mercusys.com).
- 14 -