Meridian HARVEST H1392 User manual

Read this manual before using product. Failure to follow
instructions and safety precautions can result in serious
injury, death, or property damage. Keep manual for future
reference.
H1392 

H13XX Augers:
Important Notes
At 15-20 miles, tire lug nut tightness and
wheel hub temperature need to be checked.
At 50-60 miles, check these a second time.
For the H1392, 102, and 112, the maximum
transport speed is 25 mph.
For the H1362, 72, and 82, the maximum
transport speed is 45 mph.
2

Harvest by Meridian thanks you for your purchase of the best quality auger on
the market. We are proud to have you on our team. Our equipment is
manufactured in the United States of America and is made to improve your
farming operation. Before you operate this auger, we advise that you read this
manual and familiarize yourself with each of the features. Please take all the
precautions necessary for an e!cient and safe operation. Harvest by Meridian
recommends that anyone using this auger read the operational manual and
sign on the sheet provided below. This is to be kept for your record keeping.
Date
Employee Name
Employee
Signature
3

TABLE OF CONTENTS
1. Introduction_____________________________________________________________5
2. Safety First______________________________________________________________6
3. Transportation & Placement_____________________________________________7
3.1 Before Transporting Your Auger___________________________________7
3.2 Transport Procedure_______________________________________________8
3.3 Placement of Auger________________________________________________8
3.4 Final Placement__________________________________________________10
3.5 Lowering the Auger______________________________________________10
4. Operation______________________________________________________________11
4.1 Pre-Operation Checklist__________________________________________11
4.2 Auger Drive & Lockout___________________________________________12
4.3 Start Up & Break In_______________________________________________12
4.4 Everyday Operation______________________________________________13
4.5 Shutting Down the Auger_________________________________________14
4.6 Completion & Cleanup___________________________________________14
4.7 Lowering the Auger______________________________________________15
5. Hydraulics_____________________________________________________________15
5.1 General Information______________________________________________15
5.2 Cylinder Hydraulics______________________________________________16
6. Storage & Maintenance_________________________________________________17
6.1 General Maintenance_____________________________________________17
6.2 Storage of Auger_________________________________________________19
7. Appendix & Forms_____________________________________________________20
H13XX Parts Book____________________________________________________20
H13XX Lubrication Requirements_____________________________________39
Warranty Policy and Forms___________________________________________42
4

1. Introduction
Congratulations on your choice of a Harvest by Meridian auger! This equipment
has been designed and manufactured to meet the needs of the discerning
buyer.
Safe and e!cient operation of your auger requires that you, and anyone else
who will be operating or maintaining the auger, read and understand the safety,
operation, maintenance, and troubleshooting information in this manual.
Keep this manual handy for frequent reference and to pass on to new operators
or owners. Call your Harvest by Meridian distributor or dealer if you need
assistance, information, or additional copies of the manual.
Always give your dealer the serial number of your Harvest by Meridian Grain
Auger when ordering parts or requesting service or information.
The serial number on your auger is located where indicated by the arrow in the
picture above. Please mark the number in the space provided below for easy
reference.
Model Number:_____________________________________
Serial Number:______________________________________
Production Year:_____________________________________
5

2. Safety First
Safety is a priority in your everyday work habit, especially if you work with
machinery. Whether you are an owner, an operator, or an employee, it is your
responsibility to know the operational requirements and safety precautions of
the machinery.
Why is safety important to you?
1. Accidents disable and kill.
2. Accidents cost.
3. Accidents can be avoided.
SIGNAL WORDS:
Note the use of the signal words DANGER, WARNING, CAUTION, and NOTICE
with the safety messages. The safety alert symbol identifies imminent and
potential hazards to personal health and safety. The appropriate signal word for
each message has been selected using the definitions below as a guideline:
DANGER: indicates an imminently hazardous situation that, if not
avoided, will result in serious injury or death.
WARNING: Indicates a hazardous situation that, if not avoided, could
result in serious injury or death.
CAUTION: Indicates a hazardous situation that, if not avoided, may
result in minor or moderate injury.
NOTICE: Indicates a potentially hazardous situation that, if not
avoided, may result in property damage.
6

3. Transportation and Placement
3.1 Before Transporting your Auger _
Remove wheel chocks, so wheels are free to move.
DANGER:
If auger wheels are stuck in grain, mud, dirt, or snow. remove the
restraining substance from around the wheels before transport. Failure to
do this could cause damage to the auger, and serious injury or death.
All Harvest by Meridian augers have minimum clearance positions when in
transport mode. Place auger in full down position.
DANGER:
Electrocution Hazard! Make sure that all unauthorized personnel are clear
from the transport zone. This auger is not insulated. Be alert to overhead
obstructions and electrical wires. Electrocution can occur without direct
contact. Do not raise or lower auger until hazardous area is cleared. Failure
to maintain proper clearance can result in serious injury or death.
Put hitch pin in place, and ensure that the safety chain is properly attached. Use
a type of hitch pin that will not allow the auger to detach itself from the tractor.
If you have questions about appropriate hitch pins, contact your tractor
manufacturer.
Put PTO driveline and swing hopper into transport position and lock into place.
If swing hopper is not in transport position, the hopper will be damaged during
transport.
Put jack in raised position and lock into place. Use caution when working with
hitch jack.
If you have a light package for your auger, make sure the connections are
fastened securely and not dragging on the ground.
7

3.2 Transportation Procedure _
Move auger with a tractor only. Never attempt to move by hand.
Under no condition should you allow riders on the auger or tractor.
Transport the auger no faster than 15 mph. When roads are rough or surfaces
are uneven, slow down to ensure safe travel.
DANGER:
Do not transport the auger on slopes greater than 20 degrees. This could
cause the auger to tip, resulting in damage to the auger, and personal
injury or death.
When visibility is reduced, please use caution and add extra lights to the auger.
Consider using a pilot vehicle for safer travel.
Use extreme caution when turning or cornering with the auger in tow.
Check regulations with local authorities regarding auger transportation. Follow
all over-width regulations. Equip auger with all necessary lighting, and use
hazard warning flashers on your tractor, when required by law.
3.3 Placement of Auger _
Before raising or lowering your auger, check that the area is clear of
obstructions, children and unauthorized personnel.
DANGER:
Electrocution Hazard! Make sure that all unauthorized personnel are clear
from the transport zone. This auger is not insulated. Be alert to overhead
obstructions and electrical wires. Electrocution can occur without direct
contact. Do not raise or lower auger until hazardous area is cleared. Failure
to maintain proper clearance can result in serious injury or death.
Ensure that your auger is on level ground that is free of debris.
DANGER:
If ground is very uneven, auger can tip and cause damage to the
equipment and personal injury or death.
8

WARNING:
Never position raisers of any kind under the wheels of the auger to
increase height. This includes pieces of wood, cement blocks, bricks, etc.
Attempting this could result in damage to the equipment and personal
injury or death.
Make sure that the hitch is secured to the tractor, and that all hydraulic
connections are tight and in good working condition. If there are any leaks or
damaged hoses, you must replace these before using your auger. Replacement
hoses and hose ends must have a minimum strength of 1900psi working
pressure.
Make sure that the wheels of your auger are free to move before you raise or
lower your auger.
CAUTION:
If the auger wheels are buried in any type of material, do not attempt to
raise or lower the auger. Remove dirt, snow, grain, or whatever other
material is obstructing the auger before use.
Check that the valve on the hose to the lift cylinder is open. Double check that
the area above and around the auger is clear of obstructions. Raise auger to
desired height, and
close hose valve after auger is positioned.
WARNING:
If hose valve remains open, a loss of hydraulic pressure within the tractor
system will allow the auger to lower by itself; this could cause damage to
the auger and personal injury or death.
NOTICE:
Do not use the auger as a hoist or crane, no matter the size or weight of
the object being lifted. This will create an unsafe condition and void your
warranty.
9

3.4 Final Placement of Auger _
When you are ready to use your auger, place the auger in its lowered position,
and slowly back it up to your bin or storage facility, keeping an eye out for any
people or obstructions in the hazard zone.
DANGER:
Avoid any electrical wires and overhead obstructions. Electrocution can
occur without direct contact. Failure to listen to this warning can result in
personal injury or death.
Use tractor hydraulics to raise the auger into position. Slowly back the auger
into position until the spout is over the opening of the bin or storage facility
and use tractor hydraulics to slowly lower the spout into the opening.
As soon as the auger is in position, the wheels of the auger must be chocked
on both sides. To prevent tipping, anchor or support the discharge end to the
bin or storage facility to further stabilize the auger.
3.5 Lowering the Auger _
Attach auger to tractor, making sure that your hydraulics are also attached to
the tractor. Raise the auger, to ensure that the outlet end is above the bin or
storage facility. Remove wheel chocks and ensure area is clear of personnel and
obstructions.
Drive forward, pulling auger slowly away from the bin or storage facility. Be
sure that the wheels are free to move, and lower the auger. Make sure auger is
in full down position before proceeding.
10

4. Operation
Wear protective gear at all times when operating auger, such as hard hats,
protective shoes, eye protection, and gloves. Do not wear loose clothing, and
be sure that hair is tied back.
4.1 Pre-Operation Checklist _
Before operating the auger, the operator must follow this checklist:
All safety shields are in place, secure, and in good working order.
Cables are secure.
Fasteners are secure.
PTO driveline is securely attached to driveshaft and tractor.
PTO driveline rotates freely.
PTO driveline telescopes easily.
Tube alignment is reasonably straight.
Auger wheels and tractor wheels are chocked.
Intake hopper and discharge spout are free of any obstructions.
A second qualified person is present during operation.
All operators have read manual and are aware of safety
precautions.
Maintenance has been performed properly.
Power to PTO and hydraulic system is in o#position before starting
tractor.
Hydraulic system has been thoroughly checked for leaks. (see
Section 5 “Hydraulics” for details).
11

4.2 Auger Drive & Lockout _
The proper operation of this auger requires that the operator pre-inspect the
drive system, know how to shut down the system in an emergency, and
generally monitor the system during operation.
Drive System and PTO Driveline: Ensure that the PTO drive on the tractor is in
the o#position before starting the tractor. Stay clear of PTO hazard area. Do
not exceed the maximum operation length of 34 inches of PTO driveline, or the
maximum angularity of 30 degrees.
Lockout/Shutdown of PTO Driveline: Turn o#engine. Remove ignition key
from tractor. If for some reason, you cannot remove the key, remove the PTO
driveline from the tractor.
4.3 Start Up & Break In _
DANGER:
Electrocution Hazard! Make sure that all unauthorized personnel are clear
from the operation zone. This auger is not insulated. Be alert to overhead
obstructions and electrical wires. Electrocution can occur without direct
contact. Do not raise or lower auger until hazardous area is cleared. Failure
to maintain proper clearance can result in serious injury or death.
Have you completed the pre-operational checklist? If everything is satisfactory,
prepare for a 30 minute operation at half speed to break in your auger. Double
check that the intake hopper is properly positioned, and the PTO drive on the
tractor is in the o#position.
NOTICE:
When starting the auger for the first time, be prepared for an emergency
shutdown in case of excessive vibration or noise. The auger may run
roughly until the tube is polished.
Start the tractor and idle at low RPM. Slowly engage the PTO driveline.
12

Gradually begin to feed grain into the intake hopper, bringing the speed of the
PTO to 200 RPM. Do not over-feed the hopper on initial loads; keep the feed of
the grain at half capacity. After the auger tube is polished and runs smoothly,
proceed to unload at full speed (at but not to exceed 540 RPM for maximum
e!ciency).
Upon completion of initial run, slow down until the auger is empty of grain, and
stop auger. Lock out the power source and conduct a complete inspection of
the auger, following the pre-operation checklist. After the initial start up and
inspection, the auger should be shut down and inspected at least three times
during the first hours of operation. Once your auger is broken in, the pre-
operation checklist should be part of the daily routine before you operate the
auger.
4.4 Everyday Operation _
WARNING:
When auger is in operation, keep your hands, clothing, and other objects
away from intake hopper, drive chains, and all other parts of auger to avoid
personal injury.
For normal auger operations, the following procedure and safety precautions
are strongly recommended:
Complete the pre-operation checklist before using your auger.
Remember to ground motor before using auger if an electric motor is being
used.
When using the auger, work with another trained operator present to monitor
the operation and help with a shutdown in case of an emergency. Monitor the
auger during operation for vibration and abnormal noises. If anything out of the
ordinary is noted, shut down and lock out the auger, determine the source, and
correct before continuing operation.
Keep the hopper full and running at 540 RPM for maximum capacity. Pour grain
in the middle of hopper, closest to the tube for best results.
Run the auger only when moving material. Running the auger without grain
moving through causes unnecessary wear.
13

4.5 Shutting Down the Auger _
Empty the auger of all grain. Disengage the PTO drive. Shut down and lock out
power.
WARNING:
Never use your hands to clean out debris from auger. Rather, use a small
shovel or other tool.
In the case where there has been an interruption or emergency shutdown,
restart the auger as follows:
If auger is full of grain, do not restart at full speed. Engage PTO at low RPM and
gradually increase power until normal operating speed is achieved.
CAUTION:
Starting the auger under load may result in damage to the auger. Make sure
there is no blockage.
4.6 Completion and Cleanup _
At completion of operation, the auger needs to be moved into storage position.
Make sure that the entire work area is clean, remove all supports and wheel
chocks, move auger out of working position, and fully lower the auger (see
lowering procedure below).
The proper steps for clean out of the auger are as follows:
1) Disengage power source; lower the auger into transport position.
2) Shut o#tractor and lock out power.
3) Move intake hopper into transport position and latch with safety chain.
4) If necessary, clean out grain using small shovel or other tool.
WARNING:
Do not leave auger in raised position when not in use. Auger could drop
rapidly in case of hydraulic failure. High winds may also upset the auger.
Because the hydraulic scissor lift is faster than a hand crank system, use
extra caution and clear area of personnel before raising or lowering auger.
14

4.7 Lowering the Auger _
Check that auger and hose couplers are securely attached to your tractor.
You may need to raise the auger discharge end up and out of bin or storage
facility before proceeding.
Remove wheel chocks, and check that the area around and under the auger is
clear of debris and unauthorized personnel. Wheels must be free to move when
raising or lowering the auger.
Slowly pull away from bin or storage facility. As soon as you are clear, engage
the hydraulics and lower the auger. Once valves are open, the auger lowers by
gravity. Rate of descent increases the closer the auger gets to the down
position. Be cautious.
Transport auger only in fully lowered position.
5. Hydraulics
5.1 General Information _
Be sure that all safety precautions and proper operation procedures are fully
understood before connecting the auger hydraulic hoses. Harvest by Meridian
strongly recommends doing a daily visual check for damage to the hoses and
connectors. Replace any damaged parts before operation.
WARNING:
Wear proper face and hand protection when searching for hydraulic leaks.
Fluid can escape under pressure, causing infection or toxic reaction on
skin. See a doctor immediately if injured.
Escaping hydraulic fluid can be nearly invisible under high pressure. Use some
type of backdrop when searching for leaks.
Harvest by Meridian augers have a velocity fuse for hydraulic safety. If the
hydraulic line breaks, it locks the system. Our shut o#valve is equipped with a
15

flow restrictive orifice. After you have repaired the hydraulic hose, the system
resets itself and is ready for operation.
There are various types of tractor hydraulic systems; the quick connect couplers
are supplied by the owners. Please consult your tractor manual for the proper
couplers.
Before you connect your hydraulic hoses, check that the quick connect couplers
on the auger and tractor are clean and free of any dirt or debris; wiping them
down with a cloth.
CAUTION:
Dirt in the hydraulic system can damage the cylinder o-rings. This may
cause leakage and possible system failure.
Do not disconnect the hydraulic coupler when the system is under pressure.
Relieve all pressure and then disconnect.
5.2 Cylinder Hydraulics _
The testing done on Harvest by Meridian auger hydraulics was done using a
pressure gauge with 3000psi maximum rating. This was used simply as a
guide. The psi requirements for an individual auger may vary slightly.
Auger
Size
PSI
H1062
10” x 62’
1300
H1072
10” x 72’
1400
H1082
10” x 82’
1600
H1362
13” x 62’
1600
H1372
13” x 72’
1800
H1382
13” x 82’
1900
Have approximately four liters of hydraulic fluid in your system. Check that the
valve on the hose to lift the cylinder is open. Start tractor and engage
hydraulics. Raise the auger to desired height, and close hose valve. You must
turn valve while the hydraulic system is pressurized; do not disconnect
hydraulic couplers.
16

WARNING:
If valve hose remains open, a loss of hydraulic pressure within the tractor
system could allow the auger to lower unexpectedly, causing damage to the
auger and personal injury.
To lower the auger, reconnect hose couplers to the tractor. Ensure that area is
clear and wheels are free to move. Open the hose valve, start your tractor, and
engage hydraulics. The auger is fully lowered when the tube is resting on the
tube saddle.
NOTICE:
After valves are opened, the auger lowers by gravity. As the auger nears
the full down position, the rate of descent will increase.
6. Maintenance & Storage
Proper maintenance of auger will result in both a longer life of the auger and a
safe and e!cient operation.
6.1 General Maintenance _
Always replace damaged or worn parts before using the auger. Use only
replacement parts manufactured by Harvest by Meridian. Use of unauthorized
parts will void the warranty of your auger. Contact your Harvest by Meridian
dealer to order parts.
Harvest by Meridian augers are designed and tested for a safe, e!cient
operation. Do not modify the equipment in any way. Modification to the
auger can create an unsafe working condition, a#ect the life of the
equipment, and will void your warranty.
Before performing maintenance on your auger, shut down and lock out all
power. Disconnect the PTO driveline from the tractor. Support the auger tube
before attempting maintenance on the undercarriage. The auger should be in
full down position before attempting maintenance.
17

After Maintenance is completed, replace and secure all safety shields, safety
devices, service doors and cleanout covers.
See section 5, “Hydraulics” for information on maintenance of hydraulic hoses.
See section 7, “Appendix & Forms” for expanded lube information.
Truss Cables: Replace cables if frayed or damaged. Be sure clamps are secure.
Adjust cables as needed to keep the auger tube reasonably straight.
Wheel Hubs: Repack hubs every two to three years to lengthen the life of the
hubs.
Tire Pressure: Check tire pressure monthly. The recommended tire pressure
should be maintained at 40 to 45 psi.
PTO Driveline: Lubricate both universal joints after every eight hours of
operation. Lubricate the center portion of the driveline on a yearly basis. The
first lube maintenance should be done in the first 16 to 24 hours of operation.
Then follow a regular schedule of lubing.
Lube Recommendation: Lube cross and bearing every 8 hours of use. Lube
telescoping members yearly.
NOTICE:
Replacement parts are not lubricated. When you receive these parts in,
make sure to lubricate and tighten screws.
Mechanical Chain Drive: Keep drive chain tension adjusted to about ¼”
deflection by loosening the four bolts on the lower bearing, then retightening.
Oil the chain frequently enough to keep a film of oil on the chain. This must be
done through the maintenance portal. Replace shield after maintenance.
Universal Joint: Remove PTO guard cover and lubricate grease fitting in the U-
Joint every eight hours of use. Check PTO retain bolt and retighten if necessary.
18

6.2 Storage of Auger _
Make sure that auger is in the full down position. Remove all residual material
from the hopper and auger tubes. Touch up all scratches on the auger to
prevent rusting.
Clean and re-lubricate spline on the PTO driveline. Cover with plastic bag to
protect from weather, and place it in the transport latch.
Move auger to your storage area, park, and chock wheels.
Before using the auger after storage, replace any damaged parts or decals,
remove plastic bag from PTO driveline and re-lubricate, and conduct general
maintenance procedure.
19

20
B
X1
5
X1
6
X1
7
11
X1
X1
9
X1
10
X1
X2
4
3
12
X2
X1
A
8
13
X1
ITEM NO. PART NO.
DESCRIPTION
QTY
1 10303
CLAMP, 3/8" CABLE, ZINC
8
2 10367
CLAMP, CABLE, 1/2" ZINC PLATED
12
3 11957
CABLE, TRUSS, MEDIUM, 1/2" X 71FT
2
4 11958
CABLE, TRUSS, SIDE, 3/8 X 52FT
2
5 PBH13014
HOPPER ASM, SWING, H13XX
1
6 PBH13015
SWING TUBE ASM, H13XX
1
7 PBH13026
INFEED HOUSING ASM, H1392, H13102, & H13112
1
8 PBH13032
TUBE ASM, DISCHARGE, H13112
1
9 PBH13036
TUBE ASM, 2ND SECTION, H13112
1
10 PBH13037
TUBE ASM, 3RD SECTION, 10FT TUBE, H13112
1
11 PBH13038
TUBE ASM, 1ST SECTION, H13112
1
12 PBH13039
TUBE ASM, 4TH SECTION, H13112
1
13 PBH13043
CARRIAGE ASM, H13112
1
MODEL(S)
AUGER, BASE MODEL, H1392
DRAWING NO.
PBH1392
REV PART/ASSEMBLY DESCRIPTION
H1392
DETAIL A
2
X12
DETAIL B
1
X8