Metra Electronics AT-807HD User manual

METRA. The World’s best kits.™metraonline.com © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
REV. 10/15/2015 INST-99-7898
Installation instructions for part 99-7898
CAUTION! Metra recommends disconnecting the negative bat -
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con
-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
• DIN radio provision with pocket
• ISO DIN radio provision with pocket
• Pocket holds (2) jewel cases
• A) Radio housing • B) Faceplate • C) ISO trimming • D) ISO spacers • E) ISO brackets
• F) Mounting brackets • G) Rear support bracket (R1) • H) Rear support bracket (R2)
• I) (2) #8 x 3/4” Phillips screws • J) (6) #8 x 3/8” Phillips screws
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness:
• 70-1720
• 70-1721
Antenna Adapter:
• Not required
• Phillips screwdriver • Cutting tool
TOOLS REQUIRED
Acura/Honda/Isuzu 1990-2006
99-7898
AT-807HD, IBR-807HD, CF-807HD, AW-807HD
See application list inside
B EC DA F G
H I J

2
Applications
99-7898
Table of Contents
Acura
CL ................................... 1997-1999
Integra............................. 1990-2001
Legend ............................ 1990-1995
RSX ................................. 2002-2006
TL.................................... 1996-1998
Vigor................................ 1992-1994
Honda
Accord............................. 1990-2002
Civic ................................ 1996-2000
Civic SE ........................... 2005 (only)
CRV ................................. 1997-2006
Odyssey........................... 1995-1998
Odyssey (without NAV)..... 1999-2004
Prelude............................ 1989-2001
Isuzu
Oasis ............................... 1996-1999
Dash Disassembly
- Acura CL 1997-1999 .......................................... 3
- Acura Integra 1990-1993.................................... 3
- Acura Integra 1994-2001.................................3-4
- Acura Legend 1990-1995 ................................... 4
- Acura RSX 2002-2006 ........................................ 5
- Acura TL 1996-1998........................................... 5
- Acura Vigor 1992-1994....................................... 6
- Honda Accord 1990-1993 ................................... 6
- Honda Accord 1994-1997 ................................... 7
- Honda Accord 1998-2002 ................................... 7
- Honda Civic 1996-1998 ...................................... 8
- Honda Civic 1999-2000 ...................................8-9
- Honda Civic SE 2005 (only) .................................. 9
- Honda CRV 1997-2001 ..................................... 10
- Honda CRV 2002-2006 ..................................... 10
- Honda Odyssey 1995-1998............................... 11
- Honda Odyssey 1999-2004 (without NAV)......... 11
- Honda Prelude 1989-1991................................ 12
- Honda Prelude 1992-1996................................ 12
- Honda Prelude 1997-2001................................ 13
- Isuzu Oasis 1996-1999..................................... 11
Kit Assembly
- DIN radio provision
(Honda Civic 1996-1998 only) ......................... 13
- DIN radio provision with pocket......................... 14
- ISO DIN radio provision with pocket................... 15

3
99-7898
1. Remove (3) screws
from each side of the
center console and
remove the console.
2. Remove (2) screws
securing the factory
radio to the sub-dash
support bracket. Slide
the radio/pocket
assembly out and
disconnect the wiring.
(Figure A)
3. Cut and remove all
of the mounting clips
on the radio housing
EXCEPT clips “C” and
“H” (the clips can
be identified by the
stamped letter on the
back of the housing,
near each clip).
(Figure B)
Continue to kit assembly
Acura Integra 1990-1993
Dash Disassembly
1. Unclip the radio trim
bezel and disconnect
the clock and climate
control wiring.
(Figure A)
2. Remove (2) 8mm
hex head screws
securing the factory
radio and disconnect the
wiring.
3. Cut and remove all
of the mounting clips
on the radio housing
EXCEPT clips “A” and
“H” (the clips can
be identified by the
stamped letter on the
back of the housing,
near each clip).
(Figure B)
4. Mount the rear support
bracket (R1) to the back
of the radio housing with
(2) #8 x 3/8” Phillips pan
head screws supplied. (Figure B)
Continue to kit assembly
Acura CL 1997-1999
(Figure B)
(Figure A)
“H”
“H”
“A”
(Figure B)
(Figure A)
“H”
“H”
“C”
“C”
1. Remove the cover cap located under the
emergency brake and remove (2) screws exposed.
2. Remove (2) screws from the rear corners of the
lower dash trim bezel and remove.
3. Remove the ashtray and (2) screws exposed.
4. Unsnap the ashtray housing and disconnect the
cigarette lighter harness.
5. Remove the gear shifter knob and unsnap the
shifter trim.
Continue on next page
Acura Integra 1994-2001
(Figure A)

4
99-7898
Dash Disassembly
6. Remove (2) screws below the radio opening and
remove the upper dash trim bezel. (Figure A)
7. Remove (2) 8mm screws securing the factory radio
and disconnect the wiring.
8. Cut and remove all of the mounting clips on the
radio housing EXCEPT clips “C” and “H” (the clips
can be identified by the stamped letter on the back
of the housing, near each clip). (Figure B)
Continue to kit assembly
Acura Integra 1994-2001
(Figure B)
“H”
“H”
“C”
“C”
1. Remove (2) screws below the ashtray. (Figure A)
2. Unclip the dash trim bezel.
3. Disconnect the cigarette lighter wiring and remove the bezel.
4. Remove (2) bolts securing the rear of the factory radio and
disconnect the wiring.
5. Cut and remove all of the mounting clips on the radio housing
EXCEPT clips “E” and “J” (the clips can be identified by the
stamped letter near each clip). (Figure B)
Continue to kit assembly
Acura Legend 1990-1995
(Figure B)
(Figure A)
“J”
“J”
“E”
“E”

(Figure B)
“J”
“J”
1. Using a small screwdriver, unclip the
perimeter of the radio trim bezel.
(Figure A)
2. Disconnect the climate control
and rear defroster wiring and
remove the bezel.
3. Remove (4) Phillips screws securing
the factory radio/trim bezel
assembly. (Figure A)
4. Loosen (2) Phillips screws securing
the back of the radio to the metal
housing and slide the radio out (it is
not necessary to remove the screws
securing the metal).
5. Disconnect the wiring.
6. Cut and remove all of the mounting
clips on the radio housing EXCEPT
clips “B” and “K” (the clips can be
identified by the stamped letter near
each clip). (Figure B)
Continue to kit assembly
(Figure A) (Figure B)
“K”
“K”
“B”
“B”
(Figure A)
1. Unclip the lower dash panel (containing the power outlet) and remove the panel.
2.
Reach into the opening and remove (2) Phillips screws from the base of the factory radio.
3. Slide the factory radio (with bracket assembly) from the dash and disconnect
the wiring. (Figure A)
4. Remove (4) Phillips screws securing the factory radio to the bracket assembly
and remove the radio (if a factory pocket is present, remove (4) Phillips screws
securing the pocket to the bracket assembly and remove). (Figure A)
5. Cut and remove the all mounting clips on the radio housing EXCEPT clips “J”
(the clips can be identified by the stamped letter near each clip). (Figure B)
6. Mount the rear support bracket (R2) to the back of the radio housing with (2) #8
x 3/8” Phillips pan head screws supplied.
Continue to kit assembly
Acura RSX 2002-2006 (except “S” model)
Dash Disassembly
5
Acura TL 1996-1998
99-7898

6
1. Remove the access cap from the
climate control cluster and (1) screw
exposed. (Figure A)
2. Unclip the cluster and remove (2)
screws exposed. (Figure A)
3. Remove the ashtray and (2) Phillips
screws exposed.
4. Remove the cover caps from each
front corner of the center console
and the screws exposed.
5. Open the storage compartment,
lift up the carpet and remove (2)
screws exposed.
6. Lift up on the center console and
remove. Unclip the radio trim bezel
and disconnect the wiring.
7. Remove (2) bolts from the back of the
factory radio and disconnect the wiring
.
8. Cut and remove all of the mounting
clips on the radio housing EXCEPT
clips “A” and “H” (the clips can be
identified by the stamped letter on
the back of the housing, near each
clip). (Figure B)
Continue to kit assembly
Acura Vigor 1992-1994
(Figure B)(Figure A)
“H”
“H”
“A”
“A”
“H”
“H”
“C”
“C”
1. Remove (4) screws from the lower
portion of the center console.
(Figure A)
2. Remove the gear shifter knob and
lift the console out. Remove the
ashtray and ashtray bracket.
3. Remove (2) screws from the
bottom of the radio support,
slide the radio out and disconnect
the wiring.
4. Cut and remove all of the mounting
clips on the radio housing EXCEPT
clips “C” and “H” (the clips can be
identified by the stamped letter on
the back of the housing, near each
clip). (Figure B)
Continue to kit assembly
Honda Accord 1990-1993
(Figure B)
(Figure A)
99-7898
Dash Disassembly

7
1. Remove the ashtray and (1) 3/4” #8
Phillips screw exposed. Open the
storage compartment and remove
(2) #8 Phillips screws exposed.
2. Remove the cup holder tray and (3)
#8 Phillips screws inside.
3. Lift the center console out and
remove (2) Phillips screws exposed
at the base of the dash trim bezel.
4. Unclip the bezel and remove.
5. Remove (2) hex head screws
securing the factory radio and
disconnect the wiring. (Figure A)
6. Cut and remove all of the mounting
clips on the radio housing EXCEPT
clips “A” and “H” (the clips can be
identified by the stamped letter on
the back of the housing, near each
clip). (Figure B)
7. Mount the rear support bracket (R1)
to the back of the radio housing
with (2) #8 x 3/8” Phillips pan head
screws supplied.
Continue to kit assembly
Honda Accord 1994-1997 Honda Accord 1998-2002
(Figure B)(Figure A)
1. Unsnap the clock panel, disconnect
the wiring and remove. (Figure A)
2. Remove (1) Phillips screw exposed
in the clock cavity.
3. Remove (2) Phillips screws below
the factory radio.
4. Unclip the radio trim bezel and
disconnect the wiring. (Figure A)
5. Remove (4) Phillips screws securing
the factory radio assembly and
disconnect the wiring.
6. Remove (2) screws securing the
factory pocket to the assembly.
7. Cut and remove the mounting clips
from the radio housing.
8. From the mounting brackets cut and
remove tabs “B” (the clips can be
identified by the stamped letter on
the back of the housing, near each
clip). (Figure B)
9. Secure the brackets to the
housing with (4) #8 x 3/8” Phillips
pan head screws.
Continue to kit assembly
(Figure B)(Figure A)
“B”
“H”
“H”
“A”
99-7898
Dash Disassembly

8
Honda Civic 1999-2000
1. Remove (2) Phillips screws
from the bottom edge of
the glove box door and
remove the door.
2. Remove (3) Phillips screws
from the lower steering
column panel.
3. Pull straight down
on the lower steering
column panel and remove
the panel.
4. Remove (2) Phillips screws
under the climate controls.
5. Remove (4) Phillips screws
from the lower dash
location. (Figure A)
6. Remove (4) Phillips screws
securing the bottom of
the dash trim bezel/radio
assembly and pull the
assembly out as far as
possible.
(Figure A) (Figure B)
“H”
“H”
“B”
“B”
1. Remove (2) Phillips screws from the
bottom edge of the glove box door and
remove the door.
2. Remove (3) Phillips screws from the lower
steering column panel.
3. Pull straight down on the lower steering
column panel and remove the panel.
4. Remove (2) Phillips screws under the
climate control panel. (Figure A)
5. Remove (4) Phillips screws from the lower
dash location.
6. Remove (2) 8mm hex head screws securing
the bottom-rear of the factory radio and
disconnect the wiring.
7. Locate the faceplate. (Figure B)
Continue to kit assembly
Honda Civic 1996-1998
(Figure B)
(Figure A)
99-7898
Dash Disassembly

9
Honda Civic SE 2005 (only)
1. Unsnap and remove the trim ring from
around floor shifter.
2. Unsnap and remove larger trim around
floor console shifter.
3. Remove (2) Phillips screws from in
between cup holder and shifter.
(Figure A)
4. Unsnap sides of console (2 snaps per
side) and remove with power
outlet assembly.
5. Remove (2) Phillips screws from under
radio assembly, facing up. (Figure A)
6. Remove (3) screws securing the climate
control pod to the back of the dash trim
bezel and remove the pod. (Figure B)
7. Remove (4) Phillips screws from each
side securing the factory head radio to the
bracket assembly and remove the radio.
8. Cut and remove all mounting clips on
the radio housing, EXCEPT clips “B”
and “H” (the clips can be identified by
the stamped letter on the back of the
housing, near each clip). (Figure C)
Continue to kit assembly
(Figure A) (Figure B) (Figure C)
“H”
“H”
“B”
“B”
Honda Civic
1999-2000
7. Cut the zip ties securing
the radio and climate
control wires, slide the
dash trim bezel/radio
assembly from the dash
cavity and disconnect the
wiring.
8. Cut and remove all of the
mounting clips on the
radio housing EXCEPT
clips “B” and “H” (the
clips can be identified by
the stamped letter on the
back of the housing, near
each clip).
(Figure B)
Continue to kit assembly
99-7898
Dash Disassembly

10
1. Remove (2) Phillips screws
from the bottom edge of the radio
trim bezel. (Figure A)
2. Unclip the trim bezel and remove.
3. Remove (4) Phillips screws
securing the factory radio and
disconnect the wiring.
4. Cut and remove all of the mounting
clips on the radio housing EXCEPT
clips “A” and “H” (the clips can be
identified by the stamped letter on
the back of the housing, near each
clip). (Figure B)
Continue to kit assembly
Honda CR-V 2002-2006
(Figure B)
(Figure A)
“H”
“H”
1. Open the glove box, squeeze
the retaining clips and remove
the stoppers.
2. Lower the glove box and remove (2)
Phillips screws from the left edge.
3. Remove (2) Phillips screws
from the lower steering column
panel and remove.
4. Unclip the lower console cover (below
the ashtray and pocket) and remove.
5. Remove (2) Phillips screws from the
base of the center console, open
the console pocket and remove the
(4) outer screws exposed.
6. Unclip the center console and remove.
7. Remove (2) Phillips screws securing
the radio trim bezel, disconnect the
wiring, and remove the trim bezel/
radio assembly. (Figure A)
8. Remove (4) Phillips screws securing
the radio to the bezel and remove.
9. Cut and remove all of the mounting
clips on the radio housing EXCEPT
clips “B” and “H” (the clips can be
identified by the stamped letter on
the back of the housing, near each
clip). (Figure B)
Continue to kit assembly
Honda CR-V 1997-2001
(Figure A) (Figure B)
“H”
“H”
“B”
“B”
99-7898
“A”
“A”
Dash Disassembly