Metra Electronics 99-8219 User manual

METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
APPLICATIONS
1-800-221-0932 metraonline.com
INSTALLATION INSTRUCTIONS FOR PART 99-8219
WIRING & ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
• 70-1761 Toyota harness 1987-up
Antenna Adapter:
• Not Required
Panel Removal Tool • Phillips Screwdriver
TOOLS REQUIRED
Toyota FJ Cruiser 2007-up
99-8219
B C DA
• A) Radio Housing • B) Housing Brackets • C) ISO Snap In Brackets • D) Trim Plate
KIT FEATURES
KIT COMPONENTS
• DIN radio provision with pocket
• ISO radio provision with pocket

Table of Contents
Dash Disassembly
– Toyota FJ Cruiser 2007-up 3
Kit Assembly
– DIN radio provision with pocket 4
– ISO radio provision with pocket 5
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
99-8219
Caution
Metra recommends disconnecting the negative battery terminal before beginning any
installation. All accessories, switches, and especially air bag indicator lights must be
plugged in before reconnecting the battery or cycling the ignition.
*NOTE: Refer also to the instructions included with the aftermarket radio.

1. Remove two Phillips screws from
bottom part of side trim panels.
Figure A)
2. Using a panel removal tool, carefully
remove the side trim panels. (Figure B)
3. Remove (2) Phillips screws from radio
trim panel. (Figure C)
4. Using panel removal tool, carefully
remove radio trim panel. (Figure D)
5. Remove (4) 10 mm bolts securing
the radio.
6. Unplug and remove radio.
Continue to kit assembly
3
Dash Disassembly
99-8219
(Figure B)
(Figure A)
(Figure C)
(Figure D)

4
Kit Assembly 99-8219
DIN radio provision with pocket
1. Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adapter from Metra or
AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
2. Slide the housing brackets onto the
side of the radio housing until the clips
engage. Note: Brackets are marked
left and right. (Figure A)
3. Slide the DIN cage into the radio
housing and secure by bending the
metal locking tabs outward. (Figure B)
4. Slide the aftermarket radio into the cage
and secure. (Figure C)
5. Reassemble dash in reverse order
of disassembly.
(Figure A)
(Figure B)
(Figure C)

5
Kit Assembly 99-8219
1. Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adapter from Metra or
AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
2. Slide the housing brackets onto the
side of the radio housing until the clips
engage. Note: Brackets are marked
left and right. (Figure A)
3. Mount the ISO brackets to the
aftermarket radio using the screws
supplied with the radio. (Figure B)
4. Slide the radio into the radio housing
until the side clips engage. Snap the
trim-plate into the radio housing.
(Figure C)
5. Reassemble dash in reverse order
of disassembly.
ISO radio provision with pocket
(Figure A)
(Figure B)
(Figure C)

Notes

Notes

METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
INSTALLATION INSTRUCTIONS FOR PART 99-8219
REV. 7/07/11