Metra Electronics 99-8907HG User manual

Wiring Harness: • 70-1761 Antenna Adapter: • 40-LX11
CAUTION: Metra recommends disconnecting the negative battery
terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your
local Dealership for more information. All accessories, switches,
climate controls panels, and especially air bag indicator lights
must be connected before reconnecting the battery or cycling
the ignition. Also, do not remove the factory radio with the key
in the on position, or the vehicle running. It would be best to
remove the key from the ignition and then wait a few seconds
before removing the factory radio.
Installation instructions for part 99-8907HG
•ISO DIN radio provision with pocket
•Painted two-tone silver and gloss black
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (2) Metal speed clips
• E) (2) #10 x 3/4” Phillips screws • F) (4) #8 x 3/8” Phillips screws
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
• Panel removal tool • Phillips screwdriver
• 10 mm socket wrench and long extension
TOOLS REQUIRED
Subaru Impreza and Crosstrek 2015-up
99-8907HG
ACDFE
B

99-8907HG
Dash Disassembly
1. Unsnap and remove the outside
trim panel from the driver’s side
dash. (Figure A)
2. Remove (2) Phillips screws from
the driver knee trim panel and
remove the panel. (Figure B)
3. Remove (2) 10 mm nuts now
exposed and lower the driver
airbag assembly (no need to
disconnect). (Figure C)
(Figure A) (Figure B) (Figure C)

99-8907HG
4. Release the glove box retaining
cable, squeeze the sides and lower
the glove box. (Figure D)
5. On both sides unclip and remove
the climate control cables,
accessed under the dash on the
driver side and through the glove
compartment opening on the
passenger side. (Be sure to watch
where the cables are routed).
Note, this step is not necessary
in vehicles with automatic
climate controls. (Figure E, F)
Dash Disassembly
(Figure D) (Figure E) (Figure F)
Passenger side
Driver’s side

99-8907HG
6. Remove (1) 10 mm bolt from lower
radio supports on each side of the
dash (these will be near where
the climate control cables were
removed, a long extension will be
necessary to reach them).
(Figure G, H)
7. Unsnap the vent assembly above
the radio and unplug the hazard
button. (Figure I)
Dash Disassembly
(Figure G) (Figure H) (Figure I)
Passenger side
Driver’s side

99-8907HG
Dash Disassembly
(Figure J) (Figure K)
8. Remove (2) 10 mm bolts from the
top radio mounts. (Figure J)
9. Remove and unplug the radio
from the dash.
10. Unscrew the radio brackets and
remove the factory climate controls
from the radio trim. (Figure K)

99-8907HG
Kit Assembly
(Figure B)
(Figure C)(Figure A)
ISO DIN radio provision with pocket
1. Attach the factory climate controls
to the new radio trim panel using
the factory hardware.
2. Slide the (2) provided speed clips
onto the lower factory mounting
brackets. (Figure A)
3. Attach the pocket to the brackets
using the (4) supplied #8 x 3/8”
Phillips screws. (Figure B)
4. Remove the metal “DIN” sleeve
and trim ring from the
aftermarket radio.
5. Slide the radio into the
pocket/bracket assembly and
secure using screws supplied
with the radio. (Figure C)
6. Locate the factory wiring harness
and antenna connector in the
dash, and complete all necessary
connections to the radio. Metra
recommends using the proper
mating adapter from Metra and/or
AXXESS. Re-connect the negative
battery terminal and test the radio
for proper operation.
7. Mount the radio into the dash
cavity using the factory 10 mm
bolts on the top mounts and
(2) supplied #10 x 3/4” Phillips
screws on the lower mounting
points where the speed clips were
previously attached.
8. Snap the radio trim panel over the
radio and reassemble the dash in
reverse order of disassembly.