Metra Electronics 95-1005 User manual

INSTALLATION INSTRUCTIONS FOR PART 95-1005
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION
KIT FEATURES
• Double DIN head unit provision
• Stacked ISO DIN head unit provision
A) DDIN Trim Plate | B) DDIN BRACKETS
KIT COMPONENTS
TOOLS REQUIRED:
95-1005
A B
APPLICATIONS
2003-2006 Kia Sorrento LX
(excluding sport models)
2002-2005 Kia Sedona
2002-2005 Kia Rio
2002-2006 Kia Spectra
Phillips Screwdriver I Small Flat Blade Screwdriver
Wiring Harness (Sold Separately)
• 70-1003 Kia harness 1995-2002
• 70-7301 Hyundai Kia harness 1999-2008

TABLE OF CONTENTS
95-1005
Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-8
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-10

95-1005
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Open ashtray and unclip and remove
side panels.
(Figure A)
2
2003-2006 KIA SORRENTO
(EXCLUDING SPORT MODELS)
Remove (8) Phillips screws from the
radio trim panel the remove the
panel.
(Figure B)
3
Remove (4) Phillips screws securing
radio.
(Figure C)
4
DASH DISASSEMBLY
A
B
C

95-1005
2
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Remove the ashtray and (1) Phillips
screw exposed in the ashtray cavity.
(Figure A)
2
2002-2005 KIA SEDONA
Unclip and remove the small trim
panel from around radio, climate
controls and shifter.
(Figure A)
3
Remove (4) Phillips screws from the
radio trim panel then unclip and
remove the panel.
(Figure B)
4
Remove (4) Phillips screws securing
radio.
(Figure C)
5
DASH DISASSEMBLY
A
B
C

95-1005
3
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Remove the ashtray and (1) Phillips
screw exposed in the ashtray cavity.
(1 Phillips screw exists in 2002 model
only).
(Figure A)
2
2002-2005 KIA RIO
Unclip and remove entire panel sur-
rounding radio and climate controls.
(On 2002 models remove knob from
fresh air/recirculate control).
(Figure B)
3
Remove (4) Phillips screws securing
radio.
(Figure C)
4
DASH DISASSEMBLY
A
B
C

4
95-1005
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Remove (2) Phillips facing up above
gauge cluster.
(Figure A)
2
2002-2003 KIA SPECTRA
Unsnap and remove top portion of
steering wheel column cover.
(Figure B)
3
Unsnap and remove entire panel
from left side of steering wheel to
right side surrounding radio.
(Figure C)
4
Remove (4) Phillips screws securing
radio.
(Figure D)
5
DASH DISASSEMBLY
A
B
C
D

5
95-1005 DASH DISASSEMBLY
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip and remove entire panel sur-
rounding radio and climate controls.
(Figure A)
2
2004-2006 KIA SPECTRA
Remove (4) Phillips screws securing
radio.
(Figure B)
3
A
B

95-1005
KIT ASSEMBLY
6
You will need to cut and remove the tabs according to the chart and refer-
ring to the diagram below:
The 2002-2005 Kia Sedona and the 2001-2003 Kia Spectra will use the tabs
marked by the number 2 on the brackets. Note: For the 2001-2003 Kia
Spectra proceed to page 9 for Final Assembly.
The 2002-2005 Kia Rio will use the tabs marked by the number 3 on the
brackets.
The 2003-2006 Sorrento LX and the 2004-2006 Kia Spectra will use the tabs
marked by the number 1 on the brackets.
1231
2
3
LR
TAB REMOVAL INSTRUCTIONS

95-1005
KIT ASSEMBLY
7
2
A
Slide the DDIN radio unit into the
trim plate bracket assembly and
secure the unit to the kit using the
screws supplied with the head unit.
(
Figure B)
Slide the appropriate bracket into
the trim plate aligning the holes in
the trim plate to the clips on the
bracket. (
Figure A)
1
B
DOUBLE DIN HEAD UNIT PROVISION

95-1005
KIT ASSEMBLY
8
2
A
Slide the stacked ISO DIN units into
the trim plate bracket assembly and
secure the units to the kit using the
screws supplied with the head units.
(
Figure B)
Slide the appropriate bracket into
the trim plate aligning the holes in
the trim plate to the clips on the
bracket. (
Figure A)
1
B
STACKED ISO DIN HEAD UNIT PROVISION