Metra Electronics 95-7504 User manual

METRA. The World’s best kits.™© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
REV. 3/17/2016 INST95-7504
Installation instructions for part 95-7504
metraonline.com
CAUTION! All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
• ISO DDIN radio provision
• Display replacement pocket
• A) Radio housing • B) ISO DDIN brackets • C) ISO DDIN trim plate • D) Display replacement pocket
• E) Display retention brackets • F) (2) 3/8” #10 bolts • G) (2) #10 nuts • H) (2) Plastic panel clips
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7903
Antenna Adapter: • Not required
Mazda 3 2004-2009
95-7504
G H
Dash Disassembly ..................................................2
Kit Preparation........................................................2
Kit Assembly
–ISO DDIN radio provision ...................................... 3
Table of Contents
F
• Panel removal tool • Phillips screwdriver
TOOLS REQUIRED
A EDCB

95-7504
2
Dash Disassembly Kit Preparation
1. Unclip and remove display trim
panel above radio. (Figure A)
Note: Open glove box and start in
middle of panel working towards
drivers side first, because last
connection on far passenger side
is a hook.
2.
Remove (2) Phillips screws exposed
at the top of radio, then unclip and
remove radio. (Figure B)
Note: The display is attached to
radio brackets and will be removed
at same time as radio.
3. Remove (2) Phillips screws on the
back of the display trim panel,
securing the display trim. Unclip
and remove. (Figure C)
Continue to kit preparation
Display Brackets/Pocket Assembly
Automatic Climate Control Vehicles
(2006-2009)
1. Using the (2) 3/8” #10 bolts, and (2)
#10 nuts, attach the display retention
brackets to the display unit.
2. Remove the (2) Phillips screws in the
sub dash. (Figure A)
3. Mount the display into the sub-dash
using the screws removed in step 2
.
Continue to kit assembly
Manual Climate Control Vehicles
(2004-2009)
Automatic Climate Control Vehicles
(2004-2005)
1.
Using the (2) Phillips screws removed in
step 3 of Dash Disassembly secure the
display replacement pocket to the back
of the display trim panel. (Figure B)
Continue to kit assembly
CLOCK
SET
LOAD
FM1/2
AM CD
TAPE/MD
(Figure B)
(Figure C)
HOOK
(Figure A)
REAR VIEW - DISPLAY REPLACEMENT PA NEL
DISPLAY REPLACEMENT POCKET
MOUNTED IN DISPLAY TRIM PA NEL
(Figure A)
REAR VIEW - DISPLAY REPLACEMENT PA NEL
DISPLAY REPLACEMENT POCKET
MOUNTED IN DISPLAY TRIM PA NEL
(Figure B)

95-7504
3
Kit Assembly
ISO DDIN radio provision
1. Snap the ISO DDIN brackets to the
inside edge of the radio housing.
(Figure A)
2.
Slide the radio into the bracket/radio
housing assembly, and secure using
the screws supplied with the radio.
3. Snap the trim plate onto the front of
the radio housing. (Figure B)
4. Attach the (2) plastic panel clips to
the rear of the radio housing.
(Figure C)
5. Locate the factory wiring harness
and antenna connector in the
dash, and complete all necessary
connections to the radio. Metra
recommends using the proper
mating adapter from Metra and/or
AXXESS. Test the radio for proper
operation.
6. Reassemble the dash in reverse
order of disassembly.
(Figure A)
(Figure B)
(Figure C)

METRA. The World’s best kits.™© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
REV. 3/17/2016 INST95-7504
Installation instructions for part 95-7504
metraonline.com
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
IMPORTANT
If you are having difficulties with the
installation of this product, please call our
Tech Support line at 1-800-253-TECH.
Before doing so, look over the instructions a
second time, and make sure the installation
was performed exactly as the instructions
are stated. Please have the vehicle apart
and ready to perform troubleshooting steps
before calling.

METRA. The World’s best kits.™© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
REV. 3/17/2016 INST95-7504
Instrucciones de instalación para la pieza 95-7504
metraonline.com
¡PRECAUCIÓN! Todos los accesorios, interruptores, paneles de con-
troles de clima y especialmente las luces del indicador de las bolsas
de aire deben estar conectados antes ciclar la ignición. Además, no
quite el radio de fábrica con la llave en la posición o de encendido ni
con el vehículo funcionando.
• Provisión de radio ISO DDIN
• Bolsillo de reemplazo de pantalla
• A) Carcasa del radio • B) Soportes ISO DDIN • C) Placa de moldura ISO DDIN • D) Cavidad de reemplazo de pantalla
• E) Soportes de retención de pantalla • F) (2) 3/8” x #10 pernos • G) (2) #10 nueces • H) (2) Ganchos para panel
CARACTERÍSTICAS DEL KIT
COMPONENTES DEL KIT
CABLEADO Y CONEXIONES DE ANTENA (se venden por separado)
Arnés de cableado: • 70-7903
Adaptador de antena: • No se requiere
Mazda 3 2004-2009
95-7504
G H
Desmontaje tablero ................................................2
Preparación del kit .................................................2
Ensamble del kit
–Provisión de radio ISO DDIN ................................. 3
Indice
F
• Herramienta para quitar paneles
• Destornillador Phillips
HERRAMIENTAS REQUERIDAS
A EDCB