Metra Electronics 99-7516B User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7516B
99-7516B
APPLICATIONS
Mazda CX9
2007-2009
KIT FEATURES
•DIN Head Unit Provision with Pocket
•ISO DIN Head Unit Provision with Pocket
• Double DIN Head Unit Provision
•ISO Stacked Head Unit Provision
•Painted matte black to match factory
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
•E) Double DIN Trim Plate • F) Pocket
KIT COMPONENTS
A
1-800-221-0932
©COPYRIGHT 2007-2009 METRA ELECTRONICS CORPORATION
www.metraonline.com
E
TOOLS REQUIRED:
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
•MZTO-01 - Mazda Amp Integration Harness 2007-Up
•70-7903T - Mazda service harness 2007-up
F
CD
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver

Dash Disassembly
- Mazda CX9 2007-2009 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Assembly
-DIN Head Unit Provisions with Pocket . . ......................2
-ISO DIN Head Unit Provisions with Pocket ......................3
-Double DIN Head Unit Provision/Stacked ISO DIN Head Unit Provision. . 4
TABLE OF CONTENTS
99-7516B
*Note:
Refer also to the instructions included with the aftermarket radio.
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skillsby
enrolling in the most recognizedandrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.comor call
800-354-6782 for more informationandtake steps
toward abetter tomorrow.

99-7516B DASH DISASSEMBLY
MAZDACX9 2007-2009
A
B
7373
883
0FM1ch1
VOL
PUSHPOWER
TUNE
PUSHAUDIO
LOAD/
SOURCE
SCAN
INFO
RETURN
MENU
DISP
MAP
VOICE
SEEK
TRACK
PUSH
AUTOON PUSH
OFF
PUSH
DUAL
PASS
A/CA/C
LOHI
FRONT
REAR
MODE
OUTSIDE
TEMP
PP
RR
NN
D
D
M
M
73 73
883
0FM1ch1
VOL
PUSH POWER
TUNE
PUSH AUDIO
LOAD/
SOURCE
SCAN
INFO
RETURN
MENU
DISP
MAP
VOICE
SEEK
TRACK
PUSH
AUTO ON PUSH
OFF
PUSH
DUAL
PASS
A/CA/C
LO HI
FRONT
REAR
MODE OUTSIDE
TEMP
P
P
RR
N
N
D
D
M
M
C
73 73
883
0FM1ch1
VOL
PUSH POWER
TUNE
PUSH AUDIO
LOAD/
SOURCE
SCAN
INFO
RETURN
MENU
DISP
MAP
VOICE
SEEK
TRACK
PUSH
AUTO ON PUSH
OFF
PUSH
DUAL
PASS
A/CA/C
LO HI
FRONT
REAR
MODE
OUTSIDE
TEMP
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
2
Unclip and remove both side panels
from center radio trim panel.
(Figure A)
Unclip and remove the shifter trim
panel. (Figure B)
3
Remove (1) Phillips screw from the
accessory socket trim panel then
unclip and remove the panel. (Figure C)
4
Remove (2) Phillips screws from the
radio trim panel. (Figure D)
5
Unclip and remove the entire radio
trim panel including the a/c controls.
(Figure D)
6
Remove (4) Phillips screws securing
the radio.
7
Continue to kit assembly.
E
VOL
PUSH POWER
TUNE
PUSH AUDIO
LOAD/ INFO
RETURN
MAP
VOICE
SEEK
TRACK
73 73
883
0FM1ch1
PUSH
AUTO ON PUSH
OFF
PUSH
DUAL
PASS
A/CA/C
LO HI
FRONT
REAR
MODE
OUTSIDE
TEMP

99-7516B KIT ASSEMBLY
2
DIN HEAD UNIT PROVISION WITH POCKET
2
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure A)
3
Snap the pocket into the bottom
opening of the radio housing.
(Figure B)
4 Slide the aftermarket head unit into
the cage and secure. (Figure C)
5
Reassemble dash in reverse order of
disassembly.
* Note: Refer also to the instructions included with the aftermarket radio.
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
batteryterminal and test the unit for
proper operation.
1
B
C
A

99-7516B KIT ASSEMBLY
3
ISO DIN HEAD UNIT PROVISION WITH POCKET
2
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure A)
3
Snap the pocket into the bottom
opening of the radio housing. (Figure B)
4 Slide the head unit into the radio
opening until the side clips engage.
(Figure C)
5
Snap the Trim plate into the Radio
Housing.
(Figure C)
6
Reassemble dash in reverse order of
disassembly.
* Note: Refer also to the instructions included with the aftermarket radio.
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
1
B
C
A

99-7516B KIT ASSEMBLY
4
DOUBLE DIN HEAD UNIT PROVISION/
STACKED ISO DIN HEAD UNIT PROVISION
2
Cut and remove the center bar from
the radio housing. (Figure A)
5
Snap the double DIN trim plate into
the radio housing. (Figure C)
4
Slide the Double DIN head unit or
stacked ISO head units into the
bracket/radio housing assembly and
secure the Double DIN head unit or
stacked ISO head units to the
assembly using the screws supplied
with the radio.
(Figure C)
6
Reassemble dash in reverse order of
disassembly.
3 Snap the Double DIN brackets to the
inside edge of the Double DIN trim
plate.
(Figure B)
* Note: Refer also to the instructions included with the aftermarket radio.
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
1
B
C
A

99-7516B
NOTES
5

99-7516B INSTRUCTIONS
1-800-221-0932
REV. 08/24/09 © COPYRIGHT 2007-2009 METRA ELECTRONICS CORPORATION INST99-7516B
www.metraonline.com