Metra Electronics 99-8213 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-8213
Socket Wrench • Flat Blade Screwdriver • Phillips Screwdriver • Utility Knife • Tape or Heat Shrink Tubing
1-800-221-0932 www.metraonline.com
KIT FEATURES
©COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION
•ISO DIN Head Unit Provisions with Pocket
A) Radio Housing w/ Pocket • B) Pocket • C) (2) Phillips Screws
KIT COMPONENTS
99-8213
A
APPLICATIONS
Toyota Prius 2004-2005
BC
TOOLS REQUIRED:

99-8213
DashDisassembly.....................................1-2
Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Climate Control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
TABLE OF CONTENTS

99-8213
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unsnap panel with vent on driver’s
side and remove.
(Figure A)
2
TOYOTAPRIUS 2004-2005
Remove (2) Phillips screws on panel
below steering column with hood
release on it and remove panel.
(Figure A)
3
Unclip and remove panel surrounding
under side of steering column..
(Figure B)
4
Unclip and remove panel above
steering column.
(Figure C)
5
DASH DISASSEMBLY
A
B
C
Unclip and remove vent panel sur-
rounding the shifter.
(Figure D)
6
D
Open glove box and remove vent
panel next to the radio. (Figure D)
7

99-8213
2
DASH DISASSEMBLY
TOYOTAPRIUS 2004-2005 (CON’T)
Remove (2) Phillips screws from flip
open panel below radio, unclip and
remove.
(Figure E)
8
Remove (2) 10mm bolts from info
center display above radio, unclip and
remove.
(Figure F)
9
Remove (2) 10mm bolts from top of
radio assembly.
(Figure G)
10
Remove (2) 10mm bolts from bottom
of radio assembly, unclip radio and
remove.
(Figure G)
11
Remove (4) Phillips screws to remove
factory radio from bracket assembly.
Note position of factory radio in
bracket assembly for reference in
step 1 of Kit Assembly. (Figure H)
12
E
F
G
H

99-8213
3
KIT ASSEMBLY
Position aftermarket head unit into
factory audio bracket assembly and
secureusing the top (2) screw
positions and the hardware supplied
with the new head unit.
(Figure C)
4
C
ISO DIN HEAD UNIT PROVISIONS
For the pocket to fit properly inside
the dash the sides of the pocket
need to be trimmed.
(Figure A)
1
Using a utility knife carefully cut off
the 4 round pieces on each side of
the pocket.
(Figure A)
2
Attach the pocket to the back of the
trim plate using the Phillips Screws
supplied with the kit.
(Figure B)
3
A
B

99-8213
4
CLIMATE CONTROL WIRING
When completed be sure to tape up
the wires including the resistor to
protect them from coming into
contact with any metal, and push
the 20 way connector back into
the dash. (see diagram)
4
CLIMATE CONTROL WIRING
Locate the 20 way white connector
that has 5 wires in it that was
plugged into the factory radio.
(see diagram)
1
You will need the small gauge white
wirein pin 10 and the small gauge
pink wire in pin 9. The 3 remaining
larger gauge wires are not needed
at this time. (see diagram)
2
Strip back the white and pink wires,
connect one side of the 68 OHM
resistor to the white wire and
connect the other side of the resistor
to the pink wire(see diagram).
3
For the climate controls to operate properly, the following steps
need to be followed:

99-8213
5
FINAL ASSEMBLY
1
Locate the factorywiring harness in the
dash. Metra recommends using the proper
mating adapter and making the connections
as shown. (Isolate and individually tape off
the ends of any unused wires to prevent
electrical short circuit)
2
Re-connect the negative battery terminal
and test the unit for proper operation.
3
Reassemble radio and dash assemblies in
reverse order of disassembly using the
99-8213 in place of the factorypanel.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D

INST998213
1-800-221-0932 www.metraonline.com
Rev. 04/12/07 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST99-8213