Metra Electronics 108-FD9B User manual

Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 3/10/20 INST108-FD9B
INSTALLATION INSTRUCTIONS
108-FD9B
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
Patent Pending
KIT FEATURES
• Designed specifically for the Pioneer DMH-C5500NEX 8-inch radio
• Painted scratch-resistant matte black
KIT COMPONENTS
• A) Radio bezel • B) Radio brackets • C) Back panel TOOLS REQUIRED
• 9/32” socket wrench • Panel removal tool
• Phillips screwdriver
• T-6 & T-8 Torx screwdriver
TABLE OF CONTENTS
Dash Disassembly ...............................................2-3
Kit Preparation ...................................................4-5
Kit Assembly ..........................................................6
WIRING & ANTENNA CONNECTIONS (sold separately)
Wire harness: • AXTC-FD2
Antenna adapter: • 40-EU10
A B C
Ford Ranger † 2019-Up
Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle
specific applications
† With 4.2-inch display screen

386.257.1187
|
MetraOnline.com
2
(Figure B) (Figure D)
(Figure A) (Figure C)
DASH DISASSEMBLY
Note: Figures A-F show the 8” display model
radio for illustration purposes only.
1. Unclip and remove the passenger side
a/c vent & dash panel assembly.
(Figure A)
2. Unclip and remove the a/c vent to the
left of the radio. (Figure B)
3. Unclip and remove the lower trim panels
to the left and right of the climate
controls. (Figure C)
4. Unclip and remove the lower dash panel.
(Figure D)
Continued on the next page

REV. 3/10/2020 INST108-FD9B 3
DASH DISASSEMBLY (CONT.)
(Figure H)(Figure F)
(Figure G)(Figure E)
5. Remove (2) 9/32” screws securing the
power port panel, then unclip, unplug,
and remove the panel. (Figure E)
6. Remove (6) 9/32” screws securing the
radio & climate control panel, then
unplug and remove. (Figure F)
7. Remove (4) 9/32” screws securing the
radio display, then unplug and remove.
(Figure G)
8. Remove (4) 9/32” screws securing the
radio chassis. Slide the chassis out, then
unplug and remove. (Figure H)
Continue to Kit Preparation

386.257.1187
|
MetraOnline.com
4
KIT PREPARATION
From the factory radio & climate
control panel:
1. Remove (2) T-8 Torx screws securing the
connector insert, then remove.
(Figure A)
2. Remove (16) T-8 Torx screws securing
the back panel, then remove, exposing
the circuit board inside. (Figure B)
3. Unplug the orange connector which
connects the two circuit boards together.
Remove (4) T-6 Torx screws securing the
lower and upper panels together, then
separate them. The upper panel will not
be reused. (Figure C)
Continued on the next page
(Figure B) (Figure C)
(Figure A)

REV. 3/10/2020 INST108-FD9B 5
KIT PREPARATION (CONT.)
4. Secure the radio bezel to the lower
panel using (4) factory T-6 Torx screws.
(Figure D)
5. Secure the back panel to the lower
panel using (10) factory T-8 Torx screws.
(Figure E)
6. Secure the factory connector insert into
the back panel using (2) factory T-8 Torx
screws. (Figure F)
Continue to Kit Assembly
(Figure E)(Figure D)
(Figure F)

386.257.1187
|
MetraOnline.com
6
KIT ASSEMBLY
Note: For steps 1 and 2, reference the
installation manual provided with the radio
for which hardware to use. The display
screen and radio chassis use two different
types of screws.
1. Secure the display screen to the radio
brackets using (6) screws supplied with
the radio. (Figure A)
2. Secure the radio chassis to the radio
brackets using (4) screws supplied with
the radio. (Figure B)
3. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using
the proper mating adapter from Metra
and/or Axxess. Test the radio for proper
operation.
4. Slide the radio assembly into the upper
dash, then secure using the factory
screws.
5. Reassemble the dash in reverse order of
disassembly to complete the installation
(Figure A) (Figure B)

REV. 3/10/2020 INST108-FD9B 7
(Figure C)

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 3/10/20 INST108-FD9B
INSTALLATION INSTRUCTIONS
108-FD9B
If you are having difficulties with the installation
of this product, contact our Tech Support line
either by phone at 386-257-1187, or email at
[e-mail]. Before
doing so, look over the instruction booklet a
second time and ensure that the installation was
performed exactly as the instruction booklet
is stated. Have the vehicle apart and ready to
perform troubleshooting steps before contacting
Metra/Axxess Tech Support.