Mi-Light LS3 Installation instructions

User Instruction
Model No.: LS3
Dual White Panel Light Control System

Dual White Panel Light Controller is a newly
developed high-end controller, controlled by wireless
remote controller, also with smart phone control and
4G long distance control(need WiFi box).
The controller has auto-transmitting function and with
CCT and Brightness output mode. This controller
adopt the widely used 2.4GHz wireless technology
with the features of low power consumption, long
signal transmitting and strong anti-interference,etc.
One compatible remote control many controllers at the
same time. Widely used on the controlling of hotel
lighting and home lighting.
Introduction
Auto-transmitting Diagram
Product Parameters
Model No.: LS3
Working Temperature: -20~60℃
Connection: Common anode
Control Distance: 30m
Input Voltage: DC42V~45V
Output Voltage: DC30V~40V
Output Current: 900mA
Weight: 60g
Indicator light
Auto adjust
(LED VF)
One strip controller can transmit the signals from the remote
control to another controller within 30m, as long as there is a
strip controller within 30m, the remote control distance can
be limitless.
Controller Controller Controller Controller
Auto-transmitting Auto-transmitting Auto-transmitting
Input 1 Input 2
124mm
38mm
23mm

Dual White Light Connect Diagram
After turn on the power, press “Auto adjust” button once to
correct LED VF, the indicating lamp will blink 6 times after
10 seconds;It can work normally after correcting
successfully.
Single Color Light Connect Diagram
Instructions
AC
Single Color Panel Light
V+
LED-
AC TO DC
+
AC
Dual White Panel Light
V+
WW
CW
DC42V~45V
DC30V~40V
DC30V~40V
DC42V~45V
AC TO DC
+
Step 1:
Step 2: Voltage Calibration
Connect controller to the light and power,
Suggest to buy “MEAN WELL”42V AC TO DC power supply
(See right picture).

Compatible with FUT007 / FUT091 / B2 / T2 remote controls
(Purchased separately)
Step 3: Link / Unlink
Master OFF
Master OFF
Master ON Master ON
Cooler white
Brightness+
Warmer white
Brightness-
Color
Tem p er a tu r e L in e
Indicator
Indicator
Brightness
Dimming
“ ” Zone OFF “ ” Zone OFF
“ ” Zone ON
(Link/Unlink) “ ” Zone ON
(Link/Unlink)
FUT007 Remote Link / Unlink
Link: Switch off the power, then switch on again after 5
seconds, press " " 1 time within 3 seconds;the light will blink
3 times slowly when it is done.
Unlink: Switch off the power, then switch on again after 5
seconds, press corresonding " " or master ON button 5 times
within 3 seconds;the light will blink 10 times quickly when it is
done.
FUT091 / B2 / T2 Remote Link / Unlink
Link: Switch off the power, then switch on again after 5
seconds, press " " 3 times within 3 seconds;the light will
blink 3 times slowly when it is done.
Unlink: Switch off the power, then switch on again after 5
seconds, press corresonding " " or master ON button 5 times
within 3 seconds;the light will blink 10 times quickly when it is
done.
FUT007 FUT091

Made in China
Attention
1. Please check whether the input voltage of the constant voltage power
supply is in accordance with the controller, and please check the
connection of both the cathode and anode, otherwise the controller will
be broken.
2. Please don’t connect wires with power on.
Please turn on again only when it is in right connection and no short
circuit.
3. Please do not use the controller in the place with widely range metal
area or strong electromagnetic wave nearby, otherwise, the remote
distance will be seriously affected .
Master OFFMaster ON
Brightness
Dimming
“ ” Zone OFF
“ ” Zone ON
(Link/Unlink)
B2 / T2
Color
Tem p er a tu r e
Line