Mi-Light fullwat TRIAC CONTROL User manual

Owners manual
by
TRIAC CONTROL
Smart LED control system
Dimming Controller for LED systems and conventional lighting systems
by means of an end-of-phase triac system (ELV) with push button.
Compatible with Alexa and Google Home through LENNY-WIFOX1 gateway.

TRIAC CONTROL
Smart LED control system
by
2
TRIAC controller
Modelo LENNY-TRIAC1
Input voltage AC 100-240V 50/60Hz
Output voltage AC 100-240V
Output current MAX 1.36A
Output power 150W@100VAC;
300W@240VAC
Regulation method Wireless RF, push button, APP
RF range 30m
Working temperature -10-40ºC
WiFi gateway
Model LENNY-WIFOX1
Working voltage DC5V/500mA (Micro USB)
Working temperature -20~60°C
Communication WiFi-IEEE 802.11b/g/n 2.4GHz
Working frequency 2.4GHz
Transmission power 6dBm
* Suggested AC/DC adaptors (not included): MWMU10GS
FU-ADPY10-5-USB
Control rotativo
Modelo LENNY-PAN-K1
Tensión de trabajo 3V (batería CR2032)
Potencia de transmisión 6dBm
Consumo en espera <6uA
Frecuencia de funcionamiento 2.4GHz
Distancia de control 30m
Temperatura de trabajo -10~40ºC
49
25 49
Technical specifications
90,5 15
66
2.4GHz Gateway Model No.: LENNY-WIFOX1
INPUT
DC5V / 500mASET
Input Voltage: DC5V/500mA (Micro USB)
Working Temperature: -20~60°C
Communication Mode: WiFi-IEEE 802.11b/g/n 2.4GHz
RF: 2.4GHz
2.4GHz RF Transmitting Power 6dBm
2.4GHz RF Control Distance: 30m
Link
SYS
Support amazon alexa and
google assistant control
Scan to Install APP
Made in PRC
by
2786
86
• There is no need to modify the previous installation or install new wiring.
• Low cost
• 2.4RF Remote control regulation with 30 m length performances.
• Push button regulation available.
• Trailing Edge technology (ELV)
• No gap soft regulation stepping from 10% to 100%
• Fast minimum level remote control regulation.
• Overheating and overload automatic detection to turn OFF
• Supports auto transmission and synchronization so that remote control distance to be unlimited.
• Simple connection handling with input/output terminal blocks.
• Polycarbonate fire resistant housing.

TRIAC CONTROL
Smart LED control system
by
3
Installation diagram
Functioning
Short press: Switches the connected device ON/OFF.
Long press (press and hold): increases or decreases the intensity of the light.
Connection
The maximum number of TRIACs is 25 pieces and maximum wiring distance from the push button is 20m.
To control everything with a single push button, LENNY-TRIACs must be connected in cascade according to the
connection diagram.
Connection drawing
Push button controlr
Installation
Push button
Input: AC100~240V
L
N
NC NLL1
NL
INPUT
OUTPUT
Input: AC100~240V
L
N
NC NLL1
NL
INPUT
OUTPUT
Input: AC100~240V
L
N
NC NLL1
NL
INPUT
OUTPUT
Push
button
Input: AC100~240V
L
N
NC NLL1
NL
INPUT
OUTPUT
Triac dimmable LED lighting.
Traditional filament lamp.
Halogen lamp
or AC led strip (ACCX sieres)
Triac dimmable LED lighting.
Traditional filament lamp.
Halogen lamp
or AC led strip (ACCX sieres)
Triac dimmable LED lighting.
Traditional filament lamp.
Halogen lamp
or AC led strip (ACCX sieres)
Triac dimmable LED lighting.
Traditional filament lamp.
Halogen lamp
or AC led strip (ACCX sieres)

TRIAC CONTROL
Smart LED control system
by
4
Remote and panel controls
Compatible Remote and panel controls
K1: Linking, unlinking and working.
Unlinking
Linking
LENNY-PAN-B1 LENNY-PAN-B2 LENNY-PAN-K1
LENNY-MD-087LENNY-MD-006 LENNY-MD-007
1. Learning model enter.
Procedure 1: Soft push on “SET” button from LENNY-
TRIAC1 device. Indicator led will flash very fast.
Procedure 2: Switch off, main AC source for 10 sec,
then re-connect again.
Procedure 3: Soft push on external push button while
lighting up dimming.
Procedure 1:
LENNY-TRIAC1
Push button SET continuously for 3 sec. until indicator
led flashes quickly.
Procedure 2:
1. Enter learning mode
Procedure 1: Short Push on “SET” button from LENNY-
TRIAC1. Indicator led will flash quickly.
Procedure 2: Disconnect main AC source for 10 sec
and connect again.
Procedure 3: Soft push on external push button while
lighting up dimming.
2. Push “SET BUTTON” on panel device LENNY-
PAN-K1 5 times during the first 3 seconds
since previous step implemented.
Indicator led light from device flashes 10
times very fast as unlinking confirmation is
reached.
2. Push “SET BUTTON” on panel device LENNY-PAN-K1
3 times during the first 3 seconds since previous
step implemented.
Indicator led light from device flashes 3 times as
linking confirmation is reached.
Indicator light
SET SET
Minimum brightness setting
This device must be paired to a remote control before this setting can be accessed.
1. Press and hold SET button for 3 seconds until indicator LED on the panel flashes once and indicator LED on
LENNY-TRIAC1 starts flashing.
2. Short press on panel to set between 10 brightness levels: 3%, 5%, 7%, 9%, 12%, 17%, 22%, 28%, 34%, 40%.
3. Short press on panel wheel to confirm settings set or wait 10 seconds for automatic confirmation and exit
configuration mode.

TRIAC CONTROL
Smart LED control system
by
5
FUT006, FUT007, B1/T1, B2/T2, FIT087: Linking, unlinking and working.
Linking
Unlinking
1. Enter learning mode
Procedure 1: Short Push on “SET” button. Indicator
led will flash quickly.
Procedure 2: Disconnect main voltage source for
10 sec and connect again.
Procedure 3: Soft push on external push button
while lighting up dimming.
1. Enter learning mode
Procedure 1: Short Push on “SET” button. Indicator
led will flash quickly.
Procedure 2: Disconnect main voltage source
for 10 sec and connect again.
Procedure 3: Soft push on external push button
while lighting up dimming.
2. Push ON button from selected zone on
panel or remote control, during first 3
seconds since previous step implemented
Indicator led light from device flashes 3
times as linking confirmation is reached.
2. Push ON button 5 times from selected zone
on panel or remote control, during first 3
seconds since previous step implemented.
Indicator led light from device flashes 10
times as linking confirmation is reached.
led indicador
SET
Link /Unlink button
Minimum brightness setting
This device must be paired to a remote before this setting can be accessed.
1. Press and hold OFF button on the remote until LED indicator flashes once and LED indicator on the remote
starts flashing.
2. Press OFF button to set between 10 brightness levels: 3%, 5%, 7%, 9%, 12%, 17%, 22%, 28%, 34%, 40%.
3. Press any button except OFF to confirm setting.

TRIAC CONTROL
Smart LED control system
by
6
Device auto-sync
This device can transmit the signal to another device within 30m range.
The control distance is unlimited if a device is placed every 30m.
Caution: all dimmers must be linked to a remote control device.
Important facts
1.- Main source must be switched off while installing or handling.
2.- Before anything check main AC voltage.
3.- These devices should be handled by technical staff only.
4.- Do not use devices close to metal or magnetic surfaces as they may interfere with the control signal.
Triac dimmer Triac dimmer
Auto-transmitting

TRIAC CONTROL
Smart LED control system
by
7
Mobile phone pairing (LENNY-WIFOX1)
Download and install the application on your mobile phone:
a. Via QRl code
b. Searching the Play Store for “MiBoxer”.
Register in MiBoxer:
We will receive an e-mail with a registration verification code, which we will have to enter in the application to finish
registering account.
Once on the main screen and our session started, we must add the LENNY-WIFOX1 device. To do this:
Insert your email
adress
Insert your country Choose password Accept conditions
and terms
Push “+” to
add device
Push
“add sharing”.
Select device model:
In this case, click on “2.4GHz
Gateway WL-Box1”.
It is necessary a 5Vdc/500mA power
adaptor with micro-USB to supply
LENNY-WIFOX1.
If “SYS” indicator is not flashing, press
for 3 sec on “SET” button.
Enter network name and
password.
Attention: only 2.4GHz network is
supported (no 5G) and click on
“Start configuration”.
If you wish to link your LENNY system
with our smartphone app, LENNY-
WIFOX1 gateway is necessary.

TRIAC CONTROL
Smart LED control system
by
8
A countdown will appear and once paired, it will
indicate that pairing has been successful.
Our device will appear in the list of paired devices.
Linking your smartphone.
Once you get LENNY-WIFOX1 linking, we must get
driver linking with our smartphone app.
Click on suitable device.
First we must choose whether we are going to
configure one or more zones. In this case, as it is
a zone, we enter the “change” section and select
FUT006/FUT007.
On the screen of our mobile phone we will see image as follows:
ON / OFF
Zone
If you want to change the remote
control / remote panel, click on
“change” and select the one you
have chosen from the list.
Change temperature color if our
connected device allows it.
Brightness control
Link / Unlink
Timer

TRIAC CONTROL
Smart LED control system
by
9
Now we must link our receiver with smartphone application.
In the application we can control up to 4 zones (minimum one LENNY-TRIAC1 per zone).
To do this, we must select the zone to which we are going to link our LENNY-TRIAC1.
Once the zone has been selected, we can link / unlink the device:
In the case of unlink LENNY-TRIAC1:
• Click on “Link/Unlink”.
• Click on “unlink”.
• Remove the power supply to controller for 10 seconds.
• After 10 seconds, power the controller and in the first 3 seconds, click on the mobile screen on “unlink”.
• The light will flash three 10 times and confirm correct unlinking.
Multizone with the smartphone:
If we want to control several zones only with our smartphone we will need:
• WIFI gateway (LENNY-WIFOX1). It allows us to control up to 4 zones.
• One LENNY-TRIAC1 for each zone.
Click on “Link/Unlink”.
Click on “Link”.
Remove the power supply to controller for 10
seconds.
After 10 seconds, power the controller and in
the first 3 seconds, click on the mobile screen
on “link”.
The light will flash three times and confirm
correct linking.

TRIAC CONTROL
Smart LED control system
by
10
ALEXA linking
To control our system with Alexa, we need WIFI gateway: LENNY-WIFOX1 and link it to the smartphone (see section
“Linking with smartphone”, page 7).
Multizone with Alexa: If we want to control several zones with Alexa:
• One LENNY-WIFOX1 gateway for each zone.
• One LENNY-TRIAC1 for each zone.
Install Alexa app and log in using your account.
We need to install Mi-Light Smart skill. To do so:
Once we have reached this point, we must search for devices we want to link.
Click on “more”
and select “Skill and
games”.
In the search engine
type “Mi-Light Smart”
and click on this
option.
We allow
application using.
Log in with your
MiBoxer data.
If everything is
correctly done,
we will see a message
of successful linking
We have to “detect devices”. There will
be a countdown and when device is
detected, we will get a message.
Configure device we have just detected.
Select the group to which we want to link it
in Alexa.
(with intention of saying: Alexa, turn off
“bedroom” and then turn it off). So it will
tell us that it has been configured correctly.

TRIAC CONTROL
Smart LED control system
by
11
Now you can work with standard ALEXA managing.
We can rename device to be able to
control that device only instead the whole
group, command Alexa to turn off/on the
device, etc.

TRIAC CONTROL
Smart LED control system
by
12
GOOGLE HOME linking
To control our system with Google Home, we need the WIFI gateway: LENNY-WIFOX1 and linking with smartphone (see
section “Linking with smartphone”, page 7).
Multizone with Google Home: If we want to control several zones with Google Home, we will need:
• One LENNY-WIFOX1 gateway for each zone.
• One LENNY-TRIAC1 for each zone.
We install Google Home app and log in with our Google account. If we do not have our home oage configured, we
can do it now or later.
To pair the LENNY-WIFOX1 device, follow the steps below:
Once we have reached this point, the linking is done.
Click en “más”
You may get a link
warning message.
Click on “Link” to accept.
On the main Google Home screen,
our home will appear with our
device.
Look for the “Mi-Light Smart” application
in the list of applications.
If we do it correctly, a successful
linking message will appear.
Clicking on the device icon, you are
reaching another page where you can
control the lights too.
Select
“Configure device”.
Log in with your MiBoxer data.
We can rename device to
make “name it” easier.

TRIAC CONTROL
Smart LED control system
by
13
GOOGLE ASSISTANT linking
Multizone with Google Assistant: If we want to control several zones with Google Assistant:
• One LENNY-WIFOX1 gateway for each zone.
• One LENNY-TRIAC1 for each zone.
And Install Google Assistant application via PlayStore on your phone:
We must configure it to recognize your voice. Then enter “settings” in the application and click on “Voice Match”.
The application will ask you to repeat two phrases several times.
Once this is done, we will be able to “call” our device using “Ok Google”. For example, “Ok Google turn on Fullwat” and
LED strips connected to Fullwat receiver will light up properly.