Microh Asteroid RGB User manual

1

1. INTRODUCTION AND UNPACKING
Thank you for purchasing the MICROH ASTEROID RGB laser fixture. For your own safety and
knowledge, please read this manual before installing or operating the device. This manual covers
the important information on installation and applications. Please install and operate the fixture
according to instructions. Meanwhile, please keep this manual for future reference.
The MICROH ASTEROID RGB laser fixture is manufactured following CSA standards, complying
with international standard DMX512 protocol. This fixture is applicable but not limited to large-
scale live performances, theater, studio, nightclubs and discos.
The MICROH ASTEROID RGB laser features a RGB laser effect. Please carefully unpack it
when you receive the fixture and check if it was damaged during the transportation. Please check
whether the following items are included inside the box:
Fixture – One Power Cord – One User Manual – One
2. SAFTEY INSTRUCTIONS
This device has been delivered in safe working condition. In order to maintain this condition and
to ensure safe operation, it is absolutely necessary for the user to follow the safety instructions
and warning notes written in this user manual.
If the device has been exposed to temperature changes, do not switch it on immediately. The
arising condensation could damage the device. Leave the device switched off until it has reached
room temperature, and is dry.
This device falls under protection-class I, therefore it is essential that the device be grounded.
The electrical connection must be carried out by a qualified technician.
The device should only be used with rated voltage and frequency. Make sure that the available
voltage is not higher than 120V as stated at the end of this manual.
Make sure the power cord is never crimped or damaged in any way, as this could cause shock
and damage. If your power cord is damaged in any way, please purchase a new cable from your
local MICROH dealer. Always disconnect power, when the device is not in use or before cleaning
it. Never pull out the plug by tugging the power cord.
During initial start-up, some smoke or smell may arise. This is a normal process, and does not
necessarily mean that the device is defective. It should decrease gradually. Please do not project
the beam onto combustible substances.
2

Fixtures cannot be installed on or near combustible substances. Keep more than 50cm distance
from wall for proper ventilation and air flow. If your fixture is or has become damaged in any way,
it shall be exclusively replaced or repaired by the manufacturer to avoid any hazard.
3. MOUNTING AND INSTALLATION
Caution: For added protection, mount the fixtures in areas outside walking paths, seating areas,
or in areas were the fixture might be reached by unauthorized personnel. Before mounting the
fixture to any surface, make sure that the installation area can hold a minimum point load of 10
times the device’s weight. Fixture installation must always be secured with a secondary safety
attachment, such as an appropriate safety cable. Never stand directly below the device when
mounting, removing, or servicing the fixture.
Whether installing inverted on a truss / ceiling or set on a flat level surface (see illustration
below). Be sure this fixture is kept at least 0.5m (1.5 ft.) away from any flammable materials
(decoration etc.). Always use and install the supplied safety cable as a safety measure to prevent
accidental damage and/or injury in the event the clamp fails.
Mounting Points: Overhead mounting requires extensive experience, including calculating
working load limits. A knowledge of the installation material being used and periodic safety
inspection of all installation material and the fixture are all imperative and should only be
performed by a qualified technician. Improper installation can result in bodily injury and damage.
Be sure to complete all rigging and installation procedures before connecting the main power
cord to the appropriate wall outlet.
3

Clamp Mounting: The MICROH ASTEROID RGB provides mounting bracket assembly that is to
be used to mount on a truss or the floor. When mounting this fixture to truss, be sure to secure
an appropriately rated clamp to the included bracket fitted through the center hole. As an added
safety measure, be sure to attach at least one properly rated safety cable to the fixture.
Regardless of the rigging option you choose for your MICROH ASTEROID RGB, always be sure
to secure your fixture with a safety cable. The fixture provides a built-in rigging point for a safety
cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging
point for the safety cable and never secure a safety cable to a carrying handle.
Proper Usage:This product is for overhead mounting only. For safety purposes, MICROHDJ
recommends mounting lighting effect products on steady elevated platforms or sturdy overhead
supports using suitable hanging clamps. In all cases, use safety cables. Obtain appropriate
mounting hardware from your lighting vendor.
International laser safety regulations require that laser products must be operated in the
fashion illustrated below, with a minimum of 3 meters (9.8 ft) of vertical separation
between the floor and the lowest laser light. Additionally, 3 meters of horizontal separation
is required between laser light and audience or other public spaces.
CAUTION! USE OF CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER
THAN THOSE SPECIFIED IN THIS USER MANUAL MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
4

4. DMX-512 CONTROL CONNECTIONS
This fixture complies with international USITT DMX standards and can be used with either a 3 pin
or 5 pin DMX connector. Plug in the provided 3 pin XLR cable to the female 3-pin XLR output of
your controller and the other side to the male 3-pin XLR input of the MICROH ASTEROID RGB.
To connect the units to DMX, you must daisy chain the fixtures together as referred in the
diagram below. Always end your DMX-512 connection with a DMX terminator.
For installations where the DMX cable has to run a long distance, or is in an electrically noisy
environment, it is recommended to use a DMX terminator. This helps in preventing corruption of
the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120
Ω resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of
the last fixture in the chain. Please see illustrations below.
1
23
PIN 3
PIN 2
120Ω
5

5. SETUP MENU
6. DMX CHANNEL MODES
D001 DMX
AUDI SOUND MODE
AUTO MACRO
DISPLAY
CHANNEL MODE VALUE DESCRIPTION
0-69 LASER OFF
70-139 SOUND MODE
140-209 AUTO
210-255 DMX CONTROL
0-127 COUNTER CLOCKWISE
128-255 CLOCKWISE
CH3
ROTATION SPEED
0-255 SLOW - FAST
0-29 RED
30-59 GREEN
60-89 BLUE
90-119 RED+GREEN
120-149 RED+BLUE
150-179 GREEN+BLUE
180-209 RGB
211-255 MACROS
0-20 NO FUNCTION
21-255 SLOW - FAST
CONTROL
CH5
CH4
CH2
STROBE
COLOUR
SELECTION
ROTATION
DIRECTION
CH1
6

7. TECHNICAL SPECIFICATIONS
8. MAINTENANCE AND CLEANING
The following points have to be considered during the inspection:
1) All screws for installing the device or parts of the device must be tightly connected, and must
not be corroded.
2) There must not be any deformations on the housing, colour lenses, fixations or installation
spots (ceiling, suspension, trussing).
3) Mechanically moved parts must not show any traces of wearing and must not rotate with
unbalances.
4）The electric power supply cables must not show any damage, material fatigue or sediments.
Further instructions depending on the installation spot and usage must be handled by a skilled
installer or technician. Any safety issues must be resolved.
Dimension
Net Weight
Gross Weight
Power input
Range
Rated Power
Fuse
Red
Green
Blue
Modes
DMX channels
293mm X 172mm X 103mm
DIMENSIONS, WEIGHT and POWER
5
Sound - Auto - DMX - MASTER/SLAVE
CONTROL
450nm - 300mw
532nm - 150 mw
650nm - 50mw
LASER DIODE
3A
33W
120V 6Hz
Switched
2.7Kgs
2.2Kgs
7

In order to keep the fixture in good condition and extend the life, we suggest regular cleaning to
the fixture.
1) Clean the inside and outside lens each week to avoid the light output from darkening due to
accumulation of dust, dirt, etc.
2) Clean the fan each week.
3) A detailed electrical check by approved technician every three months is advised. Ensure the
circuit contacts are in good condition.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never use
alcohol or solvents.
There are no serviceable parts inside the device. Please refer to the instructions under
“Installation instructions”.
Should you need any spare parts, please order genuine MICROH parts from your local dealer.
IF YOU SHOULD EXPERIENCE ANY PROBLEMS OR ISSUES PLEASE CONTACT MICROH
PROFESSIONAL PRODUCTS BY EMAIL AT [email protected]
In the event that your unit is defective in any way, please contact your local dealer to
obtain an RA number for service repair.
DISCLAIMER – MICROH believes that the information contained within this user manual is
accurate. However, Microh is not responsible for any error or addendums to this manual.
If you have any comments or general suggestions on how this manual can be improved
please contact [email protected]. Thank you.
8

Notes:
9

Notes:
10