MicroNet SP5008A User manual

5
Quick Installation Guide
IP Telephony Gateway
Model No.: SP5008A / SP5018A / SP5058A
6
Network Configuration
Step 1:
Go to [ Network Configuration > WAN Setting ], and select
the right connection type (static IP, DHCP, or PPPoE) according
to your ISP or actual network.
Step 2: Press the Apply button after you finish configuration.
Step 3: [ ], Go to Reboot option and press the Reboot button.
Service Registration
Step 1: (SP5018A only)
Go to [ General Configuration > PABX Connection ] for PABX
connection mode. Select "Enable" for ISP/ITSP scenario that
forbids SIP calls to/from PSTN via the gateway. By default,
PABX mode is "Disable" for normal operation.
Step 2:
Go to [ General Configuration > SIP Setting ] and set the
server information here, if this VoIP gateway wants to use SIP
Proxy service to transfer the VoIP call.
Primary and Seconary proxy / P2P IP: Specify the data of
Enable/Disable, IP address, Port number, Domain Name,
Expire time, and MWI TTL.
Primary and Secondary Outbound proxy: Fill out the
Representative Number: The representative number is
working as a SIP trunk for the selected FXS line (for all FXS
or FXO/FXS combination model) or FXO line (for all FXO
model).
Enable: Enable or disable the line to register or unregister to
SIP Proxy. By default, the setting is "Enable".
Account: Input the SIP Proxy registration account ID
Number: Input the phone number.
Password: Input the password of IP Proxy registration
account ID.
Display name: Specify the Display name of the phone
number
Step 3: Press the Apply button after you finish configuration.
Step 4: [ ]
Note: Please refer to user's manual for more details about
SIP setting, Line setting, PSTN prefix routing, Dial
plan, DM, etc..
Note:
Note:
Go to Reboot , option and press the Reboot button.
P/N: 2300-0559
7
WEEE Directive & Product Disposal
At the end its serviceable life ,this product should not be treated
as household or general waste. It should be handed over to the
applicable collection point for the recycling of electrical and
electronic equipment, or returned to the supplier for disposal.
Note:
You can retrieve the IP address of the WAN port by
keying #126# on the phone set that is connected to the
FXS port of the gateway. You will hear an IVR
announcing the current IPaddress of the WAN port.
When you select PPPoE mode, then fill out the fields of
PPPoE userID and PPPoE password for PPPoE
authentication.
When the gateway cannot get IP by DHCP or PPPoE,
original static IP address is accessible via the LAN port.
Web: www.micronet.com.tw

Introduction
Micronet SP5008A / SP5018A / SP5058Aare high-capacity SIP
Gateway Series that provides 8 FXS / 4 FXS + 4 FXO / 8 FXO
ports, and suit to build an IP-based communication platform
with other VoIP devices. They meet enterprise's requirement for
functionality (VoIP) upgrade and larger scale implementation by
interoperating with legacy PABX and IP PBX/Soft-switch.
To connect with legacy PABX, SP5018A supports PABX Mode
for PSTN backup. When network or power fails, PSTN lines
(FXO) bypass to FXS ports and users still can make/receive
calls via PSTN lines.
In addition, SP5008A includes some wonderful PABX features
for small business. They help operate users on various VoIP
applications, such as extension calling among 8 FXS ports,
inbound/outbound calls via SIP trunk, DID (direct line), DOD,
prefix routing, operator attendant, etc. Users can easily benefit
from the ease-to-use device.
Package Contents
Before you start installing the device, verify the following items
are in the package:
IP Telephony Gateway
SP5008A / SP5018A / SP5058A
Quick Installation Guide
Manual CD
Power Adapter
4
1 2
3
Key Features
IETF SIP standards compliant
Support 1 RJ-45 WAN port and 4 RJ-45 LAN ports
Support POTS interfaces: 8 FXS / 4 FXS + 4 FXO / 8 FXO
ports
Support single-account registration on FXS ports for
representative number
Support extension calling among FXS ports
Support rich call features: call hold, call transfer, call forward,
hotline, warm line, speed dial, anonymous call, P2P call, etc
Support PSTN prefix routing (SP5018A only)
Support PABX mode for legacy PABX upgrade
(SP5018A only)
Support PSTN lifeline PSTN bypass in case of power or
registration failure (SP5018A only)
Support detection of disconnect tone, polarity reversal, and
loop current drop (zero voltage) on FXO ports
Well interoperability with industry-leading IP-PBX/Soft-Switch,
such as Alcatel, Lucent, Siemens, etc.
function
LED Status Indication
The Power is on
Booting up for self test
Gateway reg. fails
Gateway reg. successes
Transmitting or receiving data /
Network connection established
Transmitting or receiving data /
Network connection established
Busy / Off-hook
Available / On-hook
Busy
Available
Physical Description
SP5008A
SP5018A
SP5058A
LED Indicators
POWER
READY
PROXY
WAN
LAN(1-4)
T(1*)
L(1*)
On / Green
Blink / Green
Blink / Green
Constant / Green
Blink / Green
Blink / Green
On / Orange
Off
On / Orange
Off
1*. SP5008A: FXS = T1 - T8
SP5018A: FXS = T1 - T4, FXO = L1 - L4
SP5058A: FXO = L1 - L8
1*.
1*.
Installation
Micronet gateway that you have purchased determines the
interfaces that you see on the rear of your unit. Just connect
your device using its telephony, power and LAN connections.
LAN
WAN
L1-L8
T1-T8
T1/L1- T4/L4
RESET
DC 12V
Connect to your PC
Connect to the internal LAN network, router,
or modem
FXS(T) / FXO(L) RJ-11 ports. FXS ports are used
to connect to telephones or PABX's trunks. FXO
ports are used to connect to PSTN line or
PABX's extensions.
Factory and hold over 5 seconds Reset button
Power adapter connection
Login the System
Set your PC with static IP address (192.168.123.x) and mask
(255.255.255.0), or DHCP mode to get IP address automatically.
Launch web browser with http://192.168.123.123/. Then, login
with username (root) and password (root).