MicroNet SP5591A User manual

Micronet SP5591A
HD1080p IR Bullet IP Camera
User Manual
Ver 1.0

1
Table of Contents
1. Introduction............................................................................................................................. 3
1.1 Features ........................................................................................................................3
1.2 Package Contents ......................................................................................................... 4
2. Introduction of the Bullet IP Camera..................................................................................... 5
2.1 Camera Dimensions...................................................................................................... 5
2.2 Camera’s Connectors.................................................................................................... 6
3. Installation............................................................................................................................... 9
3.1 Power and Ethernet Cable Connection ......................................................................... 9
3.2 Ceiling/Wall Mount Installation .................................................................................... 10
3.3 Lens Adjustment.......................................................................................................... 11
4. System Requirements .......................................................................................................... 12
5. Deleting the Existing DC Viewer.......................................................................................... 13
6. Accessing Camera................................................................................................................16
7. Configuration & Operation................................................................................................... 22
7.1 Browser-based Viewer Introduction ............................................................................ 22
7.2 Home Page ................................................................................................................. 24
7.3 System Related Settings ............................................................................................. 26
7.3.1 Host Name and System Time Setting.......................................................... 27
7.3.2 Security........................................................................................................ 29
7.3.2.1 User ............................................................................................. 30
7.3.2.2 HTTPS ......................................................................................... 33
7.3.2.3 IP Filter......................................................................................... 38
7.3.2.4 IEEE 802.1X ................................................................................ 39
7.3.3 Network........................................................................................................ 41
7.3.3.1 Basic ............................................................................................ 42
7.3.3.2 QoS (Quality of Service) .............................................................. 45
7.3.3.3 SNMP (Simple Network Management Protocol).......................... 47
7.3.3.4 UPnP............................................................................................ 49
7.3.4 DDNS........................................................................................................... 52
7.3.5 Mail .............................................................................................................. 53
7.3.6 FTP.............................................................................................................. 54
7.3.7 HTTP ........................................................................................................... 55
7.3.8 Application ................................................................................................... 56
7.3.9 Motion Detection.......................................................................................... 61
7.3.10 Tampering.................................................................................................... 66
7.3.11 Storage Management .................................................................................. 69
7.3.12 Recording .................................................................................................... 72
7.3.13 File Location ................................................................................................ 73

2
7.3.14 Iris Adjustment............................................................................................. 74
7.3.15 View Log File ............................................................................................... 75
7.3.16 View User Information ................................................................................. 76
7.3.17 View Parameters ......................................................................................... 78
7.3.18 Factory Default ............................................................................................ 79
7.3.19 Software Version ......................................................................................... 80
7.3.20 Software Upgrade........................................................................................ 81
7.3.21 Maintenance ................................................................................................ 84
7.4 Video and Audio Streaming Settings........................................................................... 86
7.4.1 Video Resolution and Rotate Type.............................................................. 86
7.4.2 Video Compression ..................................................................................... 92
7.4.3 Video OCX Protocol..................................................................................... 94
7.4.4 Video Frame Skip ........................................................................................ 95
7.4.5 Video Mask.................................................................................................. 96
7.4.6 Audio Mode and Bit Rate Settings............................................................... 97
7.5 Camera Settings.......................................................................................................... 99
7.5.1 Exposure Setting ......................................................................................... 99
7.5.2 White Balance Setting ............................................................................... 101
7.5.3 Picture Adjustment..................................................................................... 102
7.5.4 Backlight .................................................................................................... 102
7.5.5 Digital Zoom............................................................................................... 103
7.5.6 IR Function ................................................................................................ 103
7.5.7 WDR Function ........................................................................................... 104
7.5.8 Noise Reduction ........................................................................................ 104
7.5.9 TV System Setting..................................................................................... 104
7.6 Logout ....................................................................................................................... 105
Appendix A: Technical Specifications...................................................................................... 106
Appendix B: Internet Security Settings .................................................................................... 108
Appendix C: DC Viewer Download Procedure......................................................................... 112
Appendix D: Install UPnP Components.................................................................................... 114

3
1. Introduction
Micronet SP5591A HD1080p IR Bullet IP Camera is capable of serving real-time
streaming and makes image quality more smoothly. In addition to MJPEG real
time streaming, this camera develops H.264 codec to apply for high resolution
digital broadcast.
With sophisticated mechanical design plus cable management, the HD1080p IR
Bullet IP Camera is easy installed and aesthetic.
1.1 Features
Progressive Scan CMOS Sensor
Dual Streams, HD1080p + 720p real-time
H.264 and MJPEG compression
Motion Detection
Privacy Masks
WDR
Smart Picture Quality/3DNR
Tampering Alarm
Day/Night (ICR)
Micro SD Support
IR LED
Weatherproof (IP66 International)
Sunshield
ONVIF Support

4
1.2 Package Contents
Please check the package contains the following items listed below.
IR Bullet IP Camera (Cable included)
Power Terminal Block (x1)
M4 Inner Hex Wrench (x1)
M4 Self Tapping Screws (×5)
Plastic Screw Anchors (×5)
Desiccant
CD
(bundled software and documentation)
Quick Guide
Desiccant User Guide

5
2. Introduction of the Bullet IP Camera
This chapter will provide the camera dimensions and overview of the supplied
all-in-one cable for reference before installation.
2.1 Camera Dimensions
The Bullet IP Camera’s dimensions are shown below.

6
2.2 Camera’s Connectors
The Bullet IP Camera is equipped with an all-in-one cable for quick wiring.
Definition for each connector will be given as follows.
All-in-one Cable
Cable Pin No. Definition Remarks
Network
(with POE) - RJ-45 connector with LED
1 AC 24V-1 DC (-)
2 GND Reserved
Power
(3-pin Terminal Block) 3 AC 24V-2 DC (+)
Power connection
1 ALM_IN－
2 ALM_IN＋
3 ALM_OUT－
Alarm
4 ALM_OUT＋
Alarm connection
Pink Line In/ Mic In
Audio I/O Green Line Out Two-way audio transmission

7
SD Card Slot/ Reset Button
Follow the steps below to reach the SD Card Slot, Reboot Button and Factory
Default Button on IP Camera:
Step 1:
Unscrew the two screws on the Sun-
shield to remove it.
NOTE: Please note that the
Sunshield is optional.
Step 2:
Unscrew the screw on the Camera
Housing and remove the Front
Cover.
SD Card Slot

8
Factory Default Button
Reboot Button
NOTE: Before installing, please refer to Desiccant User Guide in the
package to place the Desiccant in the Camera to prevent moisture from
condensing on IP Camera’s Glass Cover.

9
3. Installation
Please read the instructions provided in this chapter thoroughly before installing
the Bullet IP Camera.
3.1 Power and Ethernet Cable Connection
Power Connection
Make sure the camera’s power cable is correctly and firmly connected; refer to
the pin definition table in section 2.2 Camera’s Connectors. If using Power over
Ethernet (PoE), make sure Power Sourcing Equipment (PSE) is in use in the
network.
Ethernet Cable Connection
Use of Category 5 Ethernet cable is recommended for network connection; to
have best transmission quality, cable length shall not exceed 100 meters.
Connect one end of the Ethernet cable to the RJ-45 connector of the IP Camera,
and the other end of the cable to the network switch or PC.
NOTE: In some cases, you may need use an Ethernet crossover cable
when connecting the IP Camera directly to the PC.
Check the status of the link indicator and activity indicator LEDs; if the LEDs are
unlit, please check LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.

10
3.2 Ceiling/Wall Mount Installation
The Bullet IP Camera can be installed directly on a wall or ceiling with the
integrated 2-axis adjustable Bracket Mount. Please note that the wall or ceiling
must have enough strength to support the IP Camera.
Follow the steps below to install the IP Camera:
Step 1:
Unpack the Bullet IP Camera package and take out the IP Camera.
Step 2:
Connect the power/Ethernet/alarm/audio wires from ceiling or wall to the
corresponding connectors of the camera’s All-in-one Cable.
Step 3:
Fix the IP Camera’s Bracket on the
ceiling/wall with three supplied self
tapping screws
Step 4:
Use the supplied Inner Hex Wrench
and cross screwdriver to loosen the
hex bolt/screw on the side of the
Bracket Mount and the Camera
Housing to adjust the position of the
IP Camera.

11
3.3 Lens Adjustment
Step 1:
Unscrew the screw on the Camera
Housing and remove the Front
Housing.
Step 2:
Connect the power/Audio/alarm I/O wires to the mating connectors. Please
refer to 3.1 Cable Connection for more cabling installing details.
Step 3:
Access the Camera Browser-viewer for viewing images. Please refer to 6.
Accessing Camera for further details.
Step 4:
Adjust the Zoom/ Focus Ring Screw on the lens to set the desired zoom/
focal length.

12
4. System Requirements
To perform the IP Camera via web browser, please ensure your PC is in good
network connection, and meet system requirements as described below.
Items System Requirement
Personal Computer
1. Intel®Pentium®M, 2.16 GHz or Intel®CoreTM2 Duo,
2.0 GHz
2. 2 GB RAM or more
Operating System Windows VISTA/ Windows XP / Windows 7
Web Browser Microsoft Internet Explorer 6.0 or later
Firefox
Chrome
Safari
Network Card 10Base-T (10 Mbps) or 100Base-TX (100 Mbps) operation
Viewer ActiveX control plug-in for Microsoft IE

13
5. Deleting the Existing DC Viewer
For users who have installed the DC Viewer in the PC previously, please first
delete the existing DC Viewer from the PC before accessing to the IP Camera.
Deleting the DC Viewer
Click “Control Panel”, and then double click “Add or Remove Programs.” In the
“Currently installed programs” list, select “DCViewer” and click the button
“Remove” to uninstall the existing DC Viewer as shown in the figure below.
Deleting Temporary Internet Files
To improve browser performance, it is suggested to clean up the all the files in
the Temporary Internet Files. The procedure is as follows:

14
STEP 1: Click the “Tools” tab and select the option “Internet Options.”
STEP 2: Click on “Delete”, then tap the “Delete Files” in the “Temporary Internet
files” section.

15
The popup window for confirmation will come out as shown below. Click “Yes” to
start deleting the files.

16
6. Accessing Camera
For initial access to the IP Camera, users can search the camera through the
installer program: IPScanUtility.exe, which can be found in “Utility” folder in the
supplied CD.
IPScanUtility Software Setup
Step 1: Double click on the program IPScanUtility.exe (see the icon below);
its window will appear as shown below. Then click the “Device Search”
button.
Step 2: The security alert window will pop up. Click “Unblock” to continue.

17
Device Search
Step 3: Click “Device Search” again, and all the finding IP devices will be listed
in the page, as shown in the figure below. The IP Camera’s default IP
address is: 192.168.1.2.
Step 4: Double click or right click and select “Browse” to access the camera
directly via web browser.
Step 5: Then the prompt window of request for entering default username
and password (as shown below) will appear for logging in to the IP
Camera.
The default login ID and password for the Administrator are:

18
Login ID Password
root pass
NOTE: ID and password are case sensitive.
NOTE: It is strongly advised that administrator’s password be
altered for the security concerns. Refer to 7.3.2 Security
for further details.
Additionally, users can change the IP Camera’s network property, either DHCP
or Static IP, directly in the device finding list. Refer to the following section for
changing the IP Camera’s network property.
Example of Changing IP Camera’s Network Property
Users can directly change an IP Camera’s network property, ex. from static IP to
DHCP, in the finding device list. The way to change the IP Camera’s network
property is specified below:
Step 1: In the finding device list, click on the IP Camera that you would like to
change its network property. On the selected item, right click and
select “Network Setup.” Meanwhile, record the IP Camera’s MAC
address, for future identification.

19
Step 2: The “Network Setup” page will come out. Select “DHCP,” and press
“Apply” button down the page.
Step 3: Click “OK” on the Note of setting change. Wait for one minute to
re-search the IP Camera.
Step 4: Click the “Device Search” button to search all the devices. Then select
the IP Camera with the correct MAC address. Double click on the IP
Camera, and the login window will come out.
Step 5: Enter User name and Password to access the IP Camera.