Microsemi PDS-104GO User manual

Copyright © 2016 Microsemi Page 1 of 48
Rev. A00 CPG –PoE BU
One Enterprise Aliso Viejo, CA 92656 USA
English
Deutsch
Microsemi Outdoor PoE
Switch
4 PoE Ports + 1 SFP Uplink Port
Microsemi PDS-104GO
Hardware Specification and Installation
Guide

Copyright © 2016 Microsemi Page 2 of 48
Rev. A00 CPG –PoE BU
One Enterprise Aliso Viejo, CA 92656 USA
Technical Support
If you encounter problems when installing or using this
product, please consult the Microsemi website at:
www.microsemi.com/products/poe-systems/poe-systems.
For technical support, call: [phone]
In the USA: 1-877-480-2323
Email: [e-mail]
Disclaimer
The information contained in the document is PROPRIETARY AND CONFIDENTIAL
information of Microsemi and cannot be copied, published, uploaded, posted, transmitted,
distributed or disclosed or used without the express duly signed written consent of Microsemi If
the recipient of this document has entered into a disclosure agreement with Microsemi, then the
terms of such Agreement will also apply . This document and the information contained herein
may not be modified, by any person other than authorized personnel of Microsemi. No license
under any patent, copyright, trade secret or other intellectual property right is granted to or
conferred upon you by disclosure or delivery of the information, either expressly, by implication,
inducement, estoppels or otherwise. Any license under such intellectual property rights must
be approved by Microsemi in writing signed by an officer of Microsemi.
Microsemi reserves the right to change the configuration, functionality and performance of its
products at any time without any notice. This product has been subject to limited testing and
should not be used in conjunction with life-support or other mission-critical equipment or
applications. Microsemi assumes no liability whatsoever, and Microsemi disclaims any express
or implied warranty, relating to sale and/or use of Microsemi products including liability or
warranties relating to fitness for a particular purpose, merchantability, or infringement of any
patent, copyright or other intellectual property right. The product is subject to other terms and
conditions which can be located on the web at http://www.microsemi.com/company/terms-and-
conditions.
2016 Microsemi Corp.
Microsemi name and logo are registered trademarks of Microsemi
Corp.
802.3at is a trademark of IEEE

Copyright © 2016 Microsemi Page 3 of 48
Rev. A00 CPG –PoE BU
One Enterprise Aliso Viejo, CA 92656 USA
English
1. Preface............................................................................4
1.1 Related Documents.................................................4
1.2 Audience.................................................................4
2. Introduction....................................................................5
3. Hardware Description....................................................5
4. Mechanical View ............................................................6
5. Installation......................................................................7
5.1 Installation Options for the PDS-104GO..................7
6. Connecting Network Cables........................................10
6.1 Connecting Gigabit Ethernet Cable.......................10
6.2 Connecting Fiber Optic Cable ...............................15
6.3 Getting Started with Switch Configuration .............16
Appendix A. Safety and Warnings.................................17
Appendix B. Troubleshooting........................................18
Appendix C. Specifications...........................................19
Appendix D. Standards ..................................................20
Appendix E. Recycling and Disposal............................21

Copyright © 2016 Microsemi Page 4 of 48
Rev. A00 CPG –PoE BU
One Enterprise Aliso Viejo, CA 92656 USA
1. Preface
This section describes the audience and organization of this
document.
1.1 Related Documents
For additional information, refer to the following documents:
Microsemi PDS-104 Software (NMS) Guide
1.2 Audience
This guide is designed for personnel who install and maintain
the switch. These persons should be familiar with electronic
circuitry and wiring practices and be experienced electronic or
electromechanical technicians.

Copyright © 2016 Microsemi Page 5 of 48
Rev. A00 CPG –PoE BU
One Enterprise Aliso Viejo, CA 92656 USA
English
2. Introduction
The Microsemi Switch 104GO/AC/M (PDS-104GO) is a 4 + 1
ports outdoor PoE Switch.It can provide power and data
connectivity for four powered devices and connect them to
the network via its data uplink port. The PDS-104GO/AC/M
can be remotely managed via web or via SNMP allowing
monitoring and control of the device and its ports. The PDS-
104GO/AC/M supports 10/100/1000Mbps data rates and it is
powered via wide-range AC input (100-240VAC). The PDS-
104GO is IP66 rated and has an extended temperature range
so it can be installed in an outdoor environment.
In a typical installation the PDS-104GO will provide power to
four outdoor devices such as WLAN AP, WLAN Mesh, IP
Camera, etc.
3. Hardware Description
The PDS-104 Switch provides fixed port configurations. This
Switch provides one GE optical port for uplink and up to four
GE copper PoE ports for downstream connectivity.
The PDS-104 switch can be either wall or pole mounted.
The PDS-104 switch provides the following hardware features:
One optical GE ports
Four copper PoE 10/100/1000BASE-T ports
Two 60W PoE copper Ports
Two 30W PoE copper Ports
Management Ethernet port (Any of the ports can be used as
Management)
Fan-less passively-cooled design
AC input
IP-66 enclosure

Copyright © 2016 Microsemi Page 6 of 48
Rev. A00 CPG –PoE BU
One Enterprise Aliso Viejo, CA 92656 USA
Four Copper cable glands
One Fiber cable gland + cable gland extender
Five ports cable gland caps
Mechanical mounting KIT option to enable pole mounting
(Optional, sold separately)
4. Mechanical View

Copyright © 2016 Microsemi Page 7 of 48
Rev. A00 CPG –PoE BU
One Enterprise Aliso Viejo, CA 92656 USA
English
5. Installation
Note Before mounting the PDS-104GO to a fixed location:
To insure weather-proof connection and in order to
meet IEC60529 level IP66, PDS-104GO AC power
plug needs to be connected to a weather-proof AC
power source box.
There is no “On-Off” switch; simply plug the PDS-
104GO into an AC main power source.
PDS-104GO AC power lines shall be connected to the
socket-outlet that shall be installed near the equipment
and shall be easily accessible.
Warning Earth ground screw must be connected to Earth ground
in all types of installations
5.1 Installation Options for the PDS-104GO
The following two sections describe installation options.
5.1.1 Wall Installation
PDS-104GO unit can be mounted on a wall/bench (all kind
of flat surfaces: wood, brick, concrete etc.) using the
mounting holes.
Fasten the PDS-104GO using four screws, see Figure 5-1.

Copyright © 2016 Microsemi Page 8 of 48
Rev. A00 CPG –PoE BU
One Enterprise Aliso Viejo, CA 92656 USA
166mm
239mm
FIGURE 5-1: WALL MOUNTING
5.1.2 Poll Installation
By using optional mount kit (sold separately).
Pole installation using optional mount kit (sold separately)
Step 1

Copyright © 2016 Microsemi Page 9 of 48
Rev. A00 CPG –PoE BU
One Enterprise Aliso Viejo, CA 92656 USA
English
Step 2
Caution! Mounting bracket must be connected to earth ground!
Step 3 For pole diameter of 1” (25.4mm) < ø < 3” (76.2mm)

Copyright © 2016 Microsemi Page 10 of 48
Rev. A00 CPG –PoE BU
One Enterprise Aliso Viejo, CA 92656 USA
Step 4 For pole diameter of 3” (76.2mm) < ø < 8” (203.2mm)
6. Connecting Network Cables
This section describes how to connect the following PDS-104GO
interfaces:
6.1 Connecting Gigabit Ethernet Cable
Note The PDS-104 is not shipped with Ethernet cable and RJ45
male connectors.