Microsemi SmartFusion A2F500-DEV-KIT-2 User manual

© 2015 Microsemi Corporation. All rights reserved.
SmartFusion Development Kit
QSG0204 Quickstart Guide
Kit Contents – A2F500-DEV-KIT-2 (RoHS-compliant)
Overview
The SmartFusion Development Kit offers a full-featured development board for SmartFusion
customizable system-on-chip (cSoC) devices. These are the only devices that integrate an FPGA,
ARM® Cortex™-M3 microcontroller, and programmable analog, offering full customization, IP
protection, and ease-of-use.
The device contains on-chip flash and SRAM memory, as well as additional off-chip memory on the
board. The board also contains LEDs, switches, and various features for extensive analog
experimentation, including voltage rail monitoring, current POT, temperature diodes, and voltage
sweeping using active bipolar prescalers (ABPS). Networking interfaces include Ethernet PHY,
EtherCAT, CAN, UART, and RS485.
Jumpers and Switch Settings
Jumpers and switches are set during the manufacturing and test of the development board. To
confirm settings, review the “Running the Manufacturing Test”. Any jumper connectors not noted
are open.
Quantity Description
1SmartFusion
®Development board with A2F500M3G-FGG484ES
1 Low-cost programming stick (LCPS)
2 USB 2.0 A to mini-B Cable
1 5 V power supply with international adapters

2
SmartFusion Development Kit Quickstart Card
SW9 must be off (JTAGSEL = H) in order to program the SmartFusion device. SW9 remains in the
off position for Libero®software and SoftConsole programming.
For a full description and location of all jumpers, refer to the SmartFusion Development Kit User’s
Guide.
Running the Manufacturing Test
You can run the manufacturing test to verify the device and board connections. The manufacturing
test files are available from the SmartFusion Development Kit page. Instructions on how to run the
test are available in the SmartFusion Development Kit User’s Guide.
Connecting the Board
Follow the steps below to connect the board:
1. Connect one of the USB cables from the PC to the USB connector on the board.
2. Connect the LCPS to the PC via a USB cable.
3. Connect the LCPS to the programming header on the board.
4. Connect the 5 V power supply to the board.
Factory Default Factory Default Factory Default
JP1: 1–2 JP12: 1–2 JP21: 1–2
JP2: 1–2 JP13: 1–2 JP22: 2–3
JP4: 1–3; 7–9 JP14: 1–2 JP23: 1–2
JP5: 1–2; 3–4 JP15: 1–2 JP24: 1–2
JP6: 2–3 JP16: 2–3 JP27: 1–2
J7: 2–3; 6–7; 10–11; 14–15 JP17: 2–3 JP28: 1-2
JP7: 1–2 JP18: 1–2 J32: 1–2; 3–4; 5–6
JP8: 3-4; 7-8; 11-12; 15-16 JP19: 2–3 –
JP11: 1-2 JP20: 1–2 –

3
SmartFusion Development Kit Quickstart Card
SmartFusion Device JP16 JP24 A2F500
Connector
JTAG Chain
Configuration Header
(JP5)
DB9 Connector
for CAN0
DB9 Connector
for CAN1
DIP Switch
RealView® Header
JTAG_SEL Switch
JP11, JP12
JP7
LCPS
Connector
DB9 Connector
for RS485 (UART1)
PUB Switch
1.5 V Header (JP6)
I2C Headers (J7)
USB Connector for UART0
JP22, JP23
JP18
Push-button Switches
SPI Headers
(JP8)
J32
DAC0 and DAC1
Callibration POTS
for ± 15 V Bipolar Outputs
JP13
Mixed Signal
Header
DACOUT/ADC
Headers (JP4)
POT for
Current Monitor
JP14, JP15, JP21,JP27
DirectC
Header (J13)
RJ45 Connectors
for EthernetCAT
Ports
JP30
RJ45 Connectors
for 10/100 Ethernet
10/100 Ethernet
Board Reset Switch
JP31
JP20
JP1, JP2
Power Jack
Power Switch
Memory Device
Configuration Headers
(JP17, JP19)
IGLOO PLUS
Header
JP28
AGLP DIP
Switch
PHY

50200204-4/04.15
SmartFusion Development Kit Quickstart Card
Software and Licensing
The SmartFusion Development Kit is supported by Libero®System-on-Chip (SoC) v10.0 or later,
which includes a web install option. SoftConsole Software IDE and FlashPro are enabled by default
in the web install; these software tools can be used for software design and debug. SmartFusion is
also supported by Keil and IAR Systems, which can be installed separately. Refer to the
SmartFusion Development Kit User’s Guide for more information.
Software releases: www.microsemi.com/products/fpga-soc/design-resources/design-software/
libero-soc
Keil and IAR information: www.microsemi.com/soc/products/smartfusion/ecosystem.aspx
Libero SoC v10.0 requires a valid Gold, Platinum, or Standalone Libero license.
If you need a new license, select FREE Libero SoC Gold license and request a new one from your
Microsemi Customer Portal account. This license supports all tools for designing with the
SmartFusion family and associated development kits.
License updates:www.microsemi.com/products/fpga-soc/design-resources/licensing
Documentation Resources
For further kit information, including user's guide, tutorial, and full design examples, refer to the
SmartFusion Evaluation Kit page:
www.microsemi.com/products/fpga-soc/design-resources/dev-kits/smartfusion/smartfusion-
development-kit
Technical Support and Contacts
Technical support is available online at www.microsemi.com/soc/support and by email at
[email protected].
Microsemi SoC Sales offices, including Representatives and Distributors, are located worldwide. To
find your local representative visit www.microsemi.com/soc/company/contact.