Microsens MS400920 User manual

Power over Ethernet Injector
User Guide
MS400920

Content
OVERVIEW ..............................................................................................................1
FEATURES ...............................................................................................................3
HARDWARE DESCRIPTION.......................................................................................4
PACKAGE CONTENTS ..............................................................................................4
INSTALLATION ........................................................................................................5

1
Overview
The Power over Ethernet Injector provides data and AC power through the
Ethernet cable to PoE-equipped device, such as AP, PoE splitter or other
equipment support IEEE 802.3af standard. The injector supports IEEE
802.3af standard that can detect the connected device, which supports
the IEEE 802.3af and then provide the power to the device. If the injector
detects that the connected device does not support the IEEE 802.3af,
then the injector will not provide the power to the connected device. The
injector is typically installed near the Ethernet hub. The following figures
show the example applications of the Power over Ethernet Injector.
Power over Ethernet Injection Application for non-PoE device

2
Power over Ethernet Injection Application for PoE device

3
Features
The following table provides the technical specification of the Power over
Ethernet Injector.
Standard
IEEE802.3 10BASE-T
IEEE802.3u 100BASE-TX
IEEE802.3af
Connector
RJ-45 Data in/out: Data/signal pairs pin 1,2,3,6
RJ-45 Power out: power over spare wire pairs
pin: 4,5(V+) , 7,8(V-)
Network Cable
10BASE-T: UTP/STP Cat.3,4,5 cable
EIA/TIA-568 100-ohm(100m)
100BASE-TX: UTP/STP Cat.5 cable
EIA/TIA-568 100-ohm(100m)
LED
System: power (green)
Power Consumption
19W
Power Supply
AC 100 ~ 240V, 50~60Hz, 0.3A
Power Output
DC [email protected]
Operating Temperature
0oC ~ 45oC
Operating Humidity
10% ~ 90% Humidity (non-condensing)
Storage Temperature
-40oC ~ 70oC
Dimension
117mm x 60mm x 35mm (W x D x H)
EMI
CE

4
Safety
CE/EN60950-1
Hardware Description
The Power over Ethernet Injector has three connection ports and one LED
indicator. We will describe each in following.
Data In port: It is an RJ-45 Ethernet interface port for data
transmitting into the PoE Injector. It is for connecting with the switch.
Power In port: The Power In port is for supplying the power into the
Injector.
The Data In and Power in port figure
Data Out port: It is an RJ-45 Ethernet port to connect with PoE
Splitter, or PD.
Data Out port figure
Package Contents
One Power over Ethernet Injector
User Manual
Four Rubber Feet
Power cord x 1, 1830mm

5
Compare the contents of your Power over Ethernet Injector package with
the standard checklist above. IF any item is missing or damaged, please
contact your local dealer for service.
Installation
To install the Power over Ethernet Injector, please follow the steps below.
1. Use RJ-45 cable to connect the Data in port of the Power over
Ethernet Injector to Switch/HUB.
2. Use RJ-45 cable to connect the Data out port of the Power over
Ethernet Injector to PoE Splitter, PD (Such as Router, Access
Point…etc.) or PoE Hub.
3. Plug in the power cord of the Power over Ethernet Injector to the wall
power plug.
4. Before starting, make sure all connections are correct.
The Power over Ethernet Injector connects to the Splitter, POE
Hub or PD via Data Out port.
The Power over Ethernet Injector connects to the switch/hub via
Data In port.
The Power In port is to get the power supply for Power over
Ethernet Injector from wall power plug.