Microtek JTX V7s User manual

i
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interfer-
ence that may cause undesired operation.
FCC WARNING
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a par-
ticular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet different from that to which
the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution:
To comply with the limits for an FCC Class B computing device, always
use the shielded signal cord supplied with this unit.
The Federal Communications Commission warns that changes or modifi-
cations of the unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

ii
CE mark for Class B ITE (Following European standard EN55022/1998;
EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998,
EN60950/1992+A1+A2+A3+A4+A11)
Radio Frequency Interference Statement
Warning:
This is a Class B product. In a domestic environment, this product may
cause radio interference in which case the user may be required to take
adequate measures.
Canadian Doc Notice
For Class B Computing Devices
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulation of the Canadian Department of Communications.
“Le présent appareil numérique n’èmet pas de bruits radioélectriques dé-
passant les limites applicables aux appareils numériques de la class B
prescrites dans le Règlement sur le brouillage radioélectrique édicté par
le ministère des Communications du Canada.”

iii
TABLE OF CONTENTS
TABLE OF CONTENTS ..........................................................................................III
Your New LCD Monitor 1
Unpacking 1
Identifying Components 3
Adjusting the Viewing Angle 5
Connecting AC Power, Video and Audio Cable 6
Power Management System 6
The LCD Monitor’s Control Panel 7
Adjusting the Monitor’s Display 9
LCD Monitor Specifications 13
Supported Timing 15
LCD Monitor Wall Mounting 15
Troubleshooting 18

1
The LCD Monitor
Your New LCD Monitor
Your LCD Monitor has been designed to be versatile, ergonomic
and user-friendly. The LCD Monitor is capable of displaying most
standards, from 640x400 VGA to 1280x1024 SXGA. The digital
controls located on the front panel allow the user to easily adjust the
Monitor’s display parameters, and the LCD Monitor’s small footprint
gives you more room in your workspace for other peripherals.
Lightweight and compact, the LCD Monitor is the perfect solution for
users on the go. You can use the LCD Monitor for everything from
making business presentations to playing computer games. The
two stereo speakers allow you to further expand your computer’s
multimedia capabilities by connecting your computer’s Audio out
port to the LCD Monitor’s Audio in port. The Monitor also has a
wall-mountable stand for added convenience.
The architecture of the LCD Monitor incorporates an LCD panel that
produces a clear display with low radiation emission. And with its
low power consumption, the LCD Monitor helps you reduce your
power bill.
Unpacking
Before unpacking your LCD Monitor, prepare a suitable workspace
for your LCD Monitor and computer. Look for a stable, level and
clean surface near a wall outlet. Even though the LCD Monitor uses
very little power, you should put it in a location which allows suffi-
cient airflow to ensure that the LCD Monitor and your computer do
not overheat. Set up your LCD Monitor so that the panel is not fac-
ing a window where sunlight often comes in. The glare caused by
sunlight reflecting off of the LCD Monitor’s screen will make it difficult
to use the Monitor for viewing.

2
Note: Using a computer for an extended period of time with a poor workstation set-
up and incorrect working habits can cause health problems. The science of ergo-
nomics studies the relationship between health and a suitable working
environment. There is a section on ergonomics at the end of this chapter. For
more information on ergonomics, contact your nearest computer bookstore, or
local library. The Internet also has information on this and other subjects.
After unpacking your LCD Monitor; make sure the following items are in-
cluded in the box and are in good condition:
•LCD Monitor
•Monitor-to-PC Analog signal cable (15-pin)
•Stereo Jack Audio Cable
•AC Adapter
•Power cord
•User’s manual
If you find any item to be missing or appear to be damaged, contact your
dealer immediately. Do not throw away the packing material or shipping
carton in case you need to ship or store the LCD Monitor in the future.

3
Identifying Components
A. The LCD Monitor — Front View
Figure 1-1: The LCD Monitor Front View
1. Power-On Indicator
This LED indicator stays lit when the power is on and blinks
when the LCD monitor is in power-saving mode.
2. Monitor Stand
3. LCD Screen
The LCD monitor screen is a 17-inch TFT 1280 x 1024 screen.
4. LCD Monitor Control Panel
Refer to Chapter 2 for more details.

4
B. "Hot Keys" for Quick Adjustment of Monitor Settings
Figure 1-2: "Hot Keys"
1. Auto-adjust "hot key":
Press button 2 to apply the monitor setting
automatically. A small “AUTO ADJUST”
OSD is also displayed.
2. Adjust-volume "hot key":
Press button 3 to allow you to adjust the
audio volume directly.
3. Contrast-adjust "hot key":
Press button 4 to allow you to adjust the
contrast of the display directly.
** To close the small OSD windows, press the power button (button 5).

5
C. The LCD Monitor — Rear View
Figure 1-3: LCD Monitor’s Rear Ports
1. DC Power Jack for AC adapter
2. Audio Line-in
3. VGA Cable Connector
Adjusting the Viewing Angle
The LCD Monitor’s vertical angle setting range is from -5°to 20°.
Figure 1-4: Angle Settings

6
Connecting AC Power, Video and Audio Cable
Figure 1-5: Connecting the LCD Monitor to the PC
Power Management System
The LCD Monitor complies with the VESA DPMS (version 1.0p) power
management proposal. The VESA DPMS proposal provides four phases
of power saving modes by detecting the horizontal or vertical sync signal.
When the LCD Monitor is in power-saving mode or detects an incorrect
timing, the Monitor screen will go blank and the power LED indicator will
start to blink.

7
The Display Controls
The LCD Monitor’s Control Panel
Figure 2-1: The Control Panel
1. OSD Menu button
Press this button to display the OSD (On-Screen Display)
menu.
2. Function button
This button lets you go through the various controls available
in the OSD (ex. Monitor Control, OSD Control, etc.)
3. Adjustment button 1
This button lets you go through the suboptions within a par-
ticular OSD control (ex. Auto Adjust, H-Position, etc. under
"Monitor Control" in the OSD). Once you are within a subop-
tion (ex. in H-Position), you can also use this button to
increase values.
4. Adjustment button 2
This button lets you adjust the values for a particular suboption
(ex. Brightness or Contrast settings under "Graphic Control" in
the OSD). Once you are within a suboption (ex. in Brightness),
you can also use this button to decrease values.

8
5. Power Switch
This button lets you turn power for the LCD monitor ON or
OFF. This is also a "hot key" to close the OSD menu while it is
on display.

9
Adjusting the Monitor’s Display
OSD Main Menu
To access the OSD main menu, press the OSD Menu button. Use the
Function Select buttons to scroll through the various OSD controls. The
highlighted OSD control is the one that is currently selected.
Analog mode
Each main menu and submenu item is covered below.
Pressing the OSD Menu button causes the following screen to appear
(an example):
Figure 2-2: The OSD Main Menu
Monitor-Control Option
The Monitor-Control option allows you to adjust the LCD
monitor’s display characteristics.
AUTO-ADJUST : Applies automatic monitor settings for
optimal viewing.
H-POSITION: Moves the LCD monitor’s display left or
right on a horizontal plane.

10
V- POSITION: Moves the LCD monitor’s display up or
down on a vertical plane.
PHASE: Adjusts the focus and clarity of the display.
CLOCK: Adjusts the display's pixel alignment.
RESET: Resets the H- Position, V-Position, Phase and
Clock parameters.
GRAPH./TEXT: Switches between the text and graphic
options.
EXIT: Exits the Monitor-Control submenu.
OSD-Control Option
The OSD-Control option lets you adjust the position of the
OSD on the screen.
OSD-H-POSITION: Changes the position of the OSD on a
horizontal plane.
OSD-V- POSITION: Changes the position of the OSD on
a vertical plane.
OSD-TIMER : Changes the OSD display time.
EXIT: Exits the OSD-Control submenu.
Graphic-Control Option
The Graphic-Control option lets you adjust the contrast,
brightness, and color of the LCD monitor’s display.

11
CONTRAST: Adjusts the difference between the lightest
and darkest areas of the LCD monitor’s display screen.
BRIGHTNESS: Adjusts the level of light or brightness on
the LCD monitor’s display screen. Brightness should be
adjusted together with Contrast.
COLOR: Selects the LCD monitor’s color display. The
available options are 9300, 6500 and User. The 9300 and
6500 options let you set the Color Temperature to CIE
coordinates 9300° or 6500° respectively. Selecting the
"User"option lets you make individual adjustments to the
R, G, and B items.
R, G and B: Makes individual adjustments to the Red
Blue Green (RGB) gain for the color temperature
Before adjusting these fields, you must select the "User"
option in the Color submenu.
AUTO-LEVEL: Adjusts automatically to perfect the white
balance display.
RESET: Resets the Contrast, Brightness and Color pa-
rameters.
EXIT: Exits the Graphic-Control submenu.
Misc-Control Option
The Misc-Control option lets you select the OSD display
language, adjust the volume setting and view system
information.
LANGUAGE: Shows the supported OSD display lan-
guages, including German, English, French, Spanish, and
Italian.
AUDIO-VOLUME: Increases or decreases the volume of
the LCD monitor’s sound system.
INFORMATION: Indicates the display mode and firmware
version of the LCD Monitor.

12
EXIT: Exits the Misc-Control submenu.
OSD Exit Option
The OSD Exit option lets you close or exit the OSD menu.
Take note that the OSD menu will close automatically if
left inactive for a few seconds.
Note:
1.No video
When the monitor is ON and there
is no Video signal received, the “NO
VIDEO” message will be displayed.
2.Signal out of monitor’s supported range
When the frequency range is out of
the monitor’s specifications, or the
incoming resolution is higher than
1280x1024, the video data will be
turned off and a warning message
“OVER RANGE” will be displayed.

13
Appendix A
LCD Monitor Specifications
LCD Panel 17-inchTFT
Control Functions
Power
Software switch with LED indicator (toggle ON/OFF)
Main Menu Submenu
Monitor Con-
trol
Auto Adjust / Horizontal Position / Verti-
cal Position / Phase / Clock / Reset /
Graph./Text / Exit
OSD Control OSD Horizontal Position / OSD Vertical
Position / OSD Timer / Exit
Graphic Con-
trol
Contrast / Brightness / Color / R / G / B /
Auto Level / Reset / Exit
Misc. Control Language / Audio Volume / Information /
Exit
On-Screen Dis-
play (OSD)
OSD Exit
Display Area 337.920 mm x 270.336 mm (17.0-inch diagonal)
Display Colors 16M
Video Interface Analog port: VGA Compatible Analog RGB (15-pin D-Sub)
Separate Sync. /Composite /Sync On Green

14
Scanning Fre-
quency (Analog
mode)
24-80K
50-75
Power Man-
agement
Meets VESA DPMS
Power Con-
sumption
ON: 40W max.
OFF/Power Saving Mode: Less than 5W
(Measured from AC inlet)
Dimensions
WxHxD
15.9 x 15.8 x 9.2 in.
(404 x 401 x 234mm)
Net Weight
Approx.
11 Lbs+2
(5kg+1)
Power Supply 100-240VAC,
50/60Hz single-phase Stand-alone AC Adapter (External)
Options Desktop and wall-mount (VESA type)
Environment Operating/Storage
Temperature:
32˚/-4˚F to
104˚/140˚F
(0˚/-20˚C to 40˚/60°C)
Relative Humidity:
10% to 85%
Altitude:
0-12,192m
(0-40,000ft)
Audio 1.0W speaker x 2 with built-in amplifier
Regulatory FCC B DoC,UL/cUL,Energy star

15
Appendix B
Supported Timing
Item Standards Resolution
Dot
Clock
(MHz)
Vertical
Scanning
Frequency
(Hz)
Horizontal
Scanning
Frequency
(kHz)
Sync Polarity
or composite
sync (H/V)
Operat-
ing Mode
1 NEC
PC98
640x400 25.20 70.15 31.50 -/- A/G
2 NEC
PC98
640x400 21.05 56.42 24.83 -/- A/G
3 MAC 13”
mode
640x480 30.24 66.67 35.00 -/- A/G
4 MAC 16”
mode
832x624 57.28 74.55 49.73 -/- A/G
5 MAC 17”
mode
1024x768 80.00 75.02 60.24 -/- A/G
6 VGA 640x350 25.18 70.09 31.47 +/- A/G
7 VGA 640x400 25.18 70.09 31.47 -/+ A/G
8 VGA 640x480 25.18 59.94 31.47 -/- A/G
9 VESA 640x480 31.50 72.81 37.86 -/- A/G
10 VESA 640x480 31.50 75.00 37.50 -/- A/G
11 VESA 800x600 36.00 56.25 35.16 +/+ A/G
12 SVGA 800x600 40.00 60.32 37.88 +/+ A/G
13 VESA 800x600 50.00 72.19 48.08 +/+ A/G
14 VESA 800x600 49.50 75.00 46.88 +/+ A/G
15 VGA 720x400 28.32 70.09 31.47 -/+ A/G
16 XGA 1024x768 65.00 60.00 48.36 -/- A/G
17 VESA 1024x768 75.00 70.07 56.48 -/- A/G
18 VESA 1024x768 78.75 75.03 60.02 +/+ A/G
19 1024x768 71.64 66.13 53.96 +/+ A/G
20 VESA 1152x864 108.00 75.00 67.50 +/+ A/G
21 1152x870 100 75.06 68.68 -/- A/G
22 VESA 1280x960 108.0 60.0 60.0 +/+ A/G
23 VESA 1280x1024 108.0 60.02 63.98 +/+ A/G
24 VESA 1280x1024 127.0 69.85 74.88 +/+ A/G
25 VESA 1280x1024 135.0 75.03 79.98 +/+ A/G
26 SUN 1024x768 64.13 59.98 48.29 H+V A
27 SUN 1024x768 74.25 70.04 56.59 H+V A
*A=Analog Mode; G=Sync On Green Mode