Midea MPM3-10CR-BB6 User manual

idea
OI w I.IA
N
ENGLISH & ESPANOL
Model: MPM3-10CR-BB6

CONTENTS
SAFETY PRECAUTIONS
Always do this ..................................................................................................................................... 2
Never do this ........................................................................................................................................ 2
Electrical information .......................................................................................................................... 2
iDENTiFiCATiON OF PARTS
Accessories ........................................................................................................................................ 3
Names of parts .................................................................................................................................... 4
AiR CONDiTiONER FEATURES
Electronic control operating instructions ............................................................................................. 5
OPERATING iNSTRUCTiONS
Operating instructions ......................................................................................................................... 9
Operating condition ........................................................................................................................ 11
iNSTALLATiON iNSTRUCTiONS
Location ............................................................................................................................................. 11
Window kit installation ....................................................................................................................... 11
Exhaust hose installation .................................................................................................................. 14
CARE AND MAINTENANCE
Care and maintenance ..................................................................................................................... 15
TROUBLESHOOTING TiPS
Troubleshooting ................................................................................................................................ 16
NOTE
The rating data indicated on the rating label is based
on the testing condition of installing the un-extended
air exhaust duct without adaptor (The duct and the
adaptor are listed in the accessories chart of the
Instruction Manual).

SAFETY PRECAUTIONS
To prevent injury to the user or other people and property damage, the following instructions must be
followed, Incorrect operation due to ignoring of instructions may cause harm or damage.
IO Always do this 1
Your air conditioner should be used in such a way
that it is protected from moisture, e.g. condensatior
splashed water, etc. Do not place or store your air
conditioner where it can fall or be pulled into water
or any other liquid. Unplug immediately.
• Always transport your air conditioner in a vertical
position and stand on a stable, level surface during
use.
• Turn off the product when not in use.
• Always contact a qualified person to carry out
repairs. If the supply cord is damaged it must be
repaired by a qualified repairer.
• Keep an air path of at least 30cm all around the
unit from walls, furniture and curtains.
• If the air conditioner is knocked over during use,
turn off the unit and unplug from the mains supply
immediately.
I(_ Neverdothis
r
• Do not operate your air conditioner in a wet room
such as a bathroom or laundry room.
o Do not touch the unit with wet or damp hands or
when barefoot.
e Do not press the buttons on the control panel with
anything other than your fingers.
• Do not remove any fixed covers. Never use this
appliance if it is not working properly, or if it has
been dropped or damaged.
• Never use the plug to start and stop the unit.
• Always use the switch on the control panel.
• Do not cover or obsturct the inlet or outlet grilles.
• Do not use hazardous chemicals to clean or come
into contact with the unit. Do not use the unit in the
presence of inflammable substances or vapour such
as alcohol, insecticides, petrol,etc.
• Do not allow children to operate the unit
unsupervised.
• Do not use this product for functions other than
those described in this instruction manual.
\ 1
I Energy Save t
• Use the unit in the recommended room size.
• Locate the unit where furniture cannot obstruct the air flow.
•Keep blinds/curtains closed during the sunniest part pf the day.
• Keep the filters clean.
• Keep doors and windows closed to keep cool air in and warm air out.
For your safety
•Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
® Avoid fire hazard or electric shock. Do not use an extension cord or an adaptor plug.
Do not remove any prong from the power cord.
Electrical information
• Be sure the electrical service is adequate for the model you have chosen. This information can be found
on the serial plate, which is located on the side of the cabinet and behind the grille.
• Be sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is
important. The power cord is equipped with a three-prong grounding plug for protection against shock
hazards.
® Your air conditioner must be used in a properly grounded wall receptacle. If the wall receptacle you intend
to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified
electrician install the proper receptacle.
® Ensure the receptacle is accessible after the unit installation.

iDENTiFiCATiON OF PARTS
Accessories
PARTS "
N
©
PARTS NAME :
Air Outlet Tie-in
Air Outlet Pipe
Air Outlet Pipe Tie-in
Adaptor (for temporary duct mounting)
Band (For bundling the power cord)
Drain Hose(Continuous drainage)
Window Slider Kit II
Window Slider Kit I
Foam
Foam
Remote Controller
Battery
PARTSNUMBER:
201125080107
201125000013
201125090064
201125090063
201125080113
201125190006
201125090002
201125090001
202125090082
202125090090
203355090205
202319900034
QUANTITY:
1
1
1
1
1
1
1
1
2
1
2
o Check all the accessories are included in the package and please refer to the installation instructions for
their usage.
|qested tools for wi.dow kit i.stallatio.
1. Screwdriver(medium size Phillips)
2. Tape measure or ruler
3. Knife or scissors
4. Saw(In the event that the window kit needs to be cut down in size because
the window is too narrow for direct installation)

iDENTiFiCATiON OF PARTS
NAMES OF PARTS
Before Using This Air Conditioner, Be Sure To Check The Back Of The
Unit To Make Sure That The Bottom Drain Plug Is Security In Place,
See Fig,2 _)
FRONT VIEW
O
0
0
O Display Panel
Horizontal Louver Blades
Signal Receptor
Air Intake (Air filter inside)
O Carrying Handle
(both sides)
REAR VIEW
Fig.1
Q
@
O Air intake
O Power Cord Outlet
Drain Outlet (Used on
dehumidifying operation)
O Air Outlet
_:_ Air Intake(Air filter inside)
Bottom Drain Plug

AiR CONDiTiONER FEATURES
ELECTRONIC CONTROL OPERATING iNSTRUCTiONS
Before you begin, thoroughly familiarize yourself with the control panel and remote controller
and all functions, then follow the symbol for the functions you desire.The unit can be controlled
by the unit control panel alone or with the remote controller.
o
FAU
o
DRY
LED DISPLAY PANEL
o
OAUTO O
COOL 0 0 o LOw O
MED O
Hi O
TEMP
SENSING
\
O
Fig.3
_) POWER button
o o L_2o
_) FAN button
O O
NOTE:
Press this button to turn unit on.
NOTE:
Used to select the Fan Speed in sequence
of LOW, MED and HIGH. Each time the button
is pressed, the fan speed mode is shifted.

AiR CONDiTiONER FEATURES
_) TEMP SENSING Feature
0 o
RE. O
HI TEC)p
SENT
NOTE:
The remote control serves as a remote
thermostat allowing for the precise
temperature control at its location.
To activate the Temp Sensing feature, point the remote
control towards the unit and press the TEMP SENSING
button. The remote display is actual temperature at its
location.
The remote control will send signal to the air conditioner
every 3 minutes interval. If the unit does not receive the
Temp Sensing signal during any 7 minutes interval, the
TEMP SENSING indicator light turns off to indicate the
TempSensing mode has ended.
The actual temperature can be displayed at the
unit by pressing the Fan Only mode. When in the
Cool mode, the unit display indicates the set
temperature.
0 SWING button
9
0 0
_E. O
HI O
TeMe
SEN_INe
NOTE:
Use the SWING button to initiate the airflow
direction setting operation(This button is available
only when the unit is on ).
1. Press the SWING button, the swing feature is
activated.
2. Each press will change the swing angle for 6°.
Keep pressing the button to move the horizontal
louver to the desired position.
If keep pressing the SWING button without
releasing for 2 more seconds, the horizontal
louver would swing up/down automatically.
3. Press the SWING button again to stop the
movement.

AiR CONDITIONER FEATURES
(_UP{A) and DOWN(Y) button
Press to decrease Press to increase
o o o
LOW 0
HU 0
TEHP
SE_SINe
NOTE:
Press or hold either UP or DOWN button
until the desired temperature is seen on the
display. This temperature will be automatically
maintained anywhere between 62°F(17°C) and
88°F(30°C). If you want the display to read the
actual room temperature, see" To Operate on
Fan Only" section.
The control is capable of displaying temperature
in degrees Fahrenheit or degrees Celsius. To
convert from one to the other, press and hold the
UP and DOWN buttons at the same time for 3
seconds.
{_ TIMER button
0
0Au'ro 0
0 cool
0_r_v
FA_
0 0
TI_ER O_ TIMER OFF
%
NOTE:
• When the unit is on, first press the Timer button,
the indicator light above word TIMER OFF illu-
minates. It indicates theAuto Stop program is
initiated.
• When the unit is off, first press the Timer button,
the indicator light above word TIMER ON illu-
minates. It indicates theAuto Start program is
initiated.
• Press or hold the UP arrow or DOWN arrow to
change the Auto time by 0.5 hour increments,
up to 10 hours, then at 1 hour increments up to
24 hours. The control will count down the time
remaining until start.
• The selected time will register in 5 seconds and
the system will automatically revert back to
display the previous temperature setting.
o Turning the unit ON or OFF at any time or
adjusting the timer setting to 0.0 will cancel
the Auto Start/Stop function.
• When LED display window displays code of El,
E2, P1 or theAuto Start/Stop function will also
be cancelled.
TURBO button
0
FAN
O O
OTIMER 0_ TIMER ¢_FF
0 AUTO 0
NOTE:
Used to set the strong fan speed, the set
temperature will reach in the shortest time.
This function is only available in COOL mode.

AiR CONDITIONER FEATURES
_) MODE select button
O
0 AUTO 0
0COOL
FAN
0 0
11MER ON TIMER OFF
NOTE:
oTo choose operating mode, press the MODE
button. Each time you press the button, a mode
is selected in a sequence that goes from Auto,
Cool, Dry, Fan The indicator light beside will be
illuminated and remained on once the mode is
selected.
To operate on Auto feature:
• In this mode, the fan speed can not be adjusted,
it starts automatically at a speed according to
the room temperature. If the room does not
get too warm, it will stay at Low speed.
To operate on Fan Only:
• Use this function only when cooling is not
desired, such as for room air circulation.
You can choose any fan speed you prefer.
• During this function, the display will show the
actual room temperature, not the set temper-
ature as in the cooling mode.
QSLEEP button
O O
% % ,O..oo
.,ooo
NOTE:
In this mode, the selected temperature will
increase(cooling) by 1°C/2°F 30 minutes.
The temperature will then increase(cooling)
by another 1°C/2°F after an additional 30
minutes.
This new temperature will maintain for
7 hours before it returns to the originally
selected temperature.
The Sleep mode program can be cancelled
at any time during operation by again pressing
the SLEEP button,or turning off the unit, or
pressing the MODE or FAN button.This feature
is unavailabe under FAN or DRY mode.
_) LED Display
O O
% % ,O..oo
.,ooo
NOTE:
Shows the set temperature in "_C" or "°F"
and the Auto-timer settings.
Error codes:
El- Room temperature sensor error-
Unplug the unit and plug it back in. If
error repeats, call for service.
E2- Evaporator temperature sensor error-
Unplug the unit and plug it back in. If
error repeats, call for service.
E3= Conenser temperature sensor error-
Unplug the unit and plug it back in. If
error repeats, call for service.
PI= Bottom tray is full- Remove the bottom
drain plug and drain off the water.

OPERATING iNSTRUCTiONS
OPERATING iNSTRUCTiONS
2
COOLING OPERATION
- Press the "MODE" button several times until the "COOL" indicator light comes on.
- Press the UP and DOWN buttons "A" or "y" to select your desired room temperature.
The temperature can be set within a range of 17°C-30°C/62°F-88°F.
- Press the "FAN " or "TURBO "button to choose the fan speed.
DRY OPERATION (DEHUMIDIFY)
Press the "MODE" button until the "DRY" indicator light comes on.
Under this mode, you cannot select a fan speed or adjust the temperature. The fan motor
operates at LOW speed.
Keep windows and doors closed for the best dehumidifying effect.
The duct can be removed when in DRY mode.
FAN OPERATION
Press the "MODE" button until the "FAN " indicator light comes on.
Press the "FAN " button to choose the fan speed. The temperature can not be adjusted.
The duct can be removed when in FAN mode.
AUTO OPERATION
Press the "MODE" button until the "AUTO " indicator light comes on.
Under this mode, you can not select a fan speed. The fan motor operates atAuto fan
speed. The temperature can be set within a range of 17°C-30°C/62°F-88°F.
TIMER OPERATION
The AUTO-TIMER feature offers a unique option to pre-set the on and off times of the unit via a 0.5 hr to 24hr
timer.
Note: The Mode, Fan Speed and Temperature settings must be selected prior to using the Auto-Rmer function.
1) Timer-Off setting.
Please be aware that in order for the Timer=Off function to work properly, the unit must be powered on.
Example: If at 8:00 pm the Timer-Off is set at 2.0, then the unit will automatically power off and stop cooling
at 10:00 p.m. or after 2 hours have elapsed.
a) Push the Timer-Off button: - The display will indicate the number of hours until the unit shuts off.
b) Press or hold the Timer-Off button until the display window indicates the number of hours that is desired
for the unit to continue running,
c)After a 5 second delay, the display will switch back from the time increment to the desired temperature
setting