Miele PT 8507 D User manual

Installation Plan
Tumble dryer
PT 8507 D (Steam Heated)
en - US
05.15 M.-Nr. 10 027 130/00

2
It isessential to read the operating and installation instructions before installing,
commissioning or using the machine.
This avoids the risk ofaccidents or damage.
All rights reserved.
U.S.A.
Miele, Inc.
National Headquarters
9 Independence Way
Princeton, NJ 08540
Phone:
Fax:
www.mieleusa.com
Technical Service & Support
Nationwide
Phone: [phone]
Fax: [phone]
[email protected]
800-991-9380
609-419-4241

>3/4
>3/4
47 1/2
47 1/4
30 1/8 20 1/2
64 5/8
64 5/8
63
28
1 1/2
24 3/4
PT 8507 D - measurements in inches
3

<
40 1/8
47 1/4
47 1/2
36
63
2
5 7/8
6 1/4
6 3/8
PT 8507 D - measurements in inches
4

34 1/2 12 3/4
66 7/8
2 1/8
27 3/4
17 5/8
7
4 7/8
12
7 7/8
66 7/8
27 3/4
17 5/8
1/2
2 5/8
4 7/8
PT 8507 D - measurements in inches
5

64 5/8
3/4
2 1/8 2 1/8
26 3/4
36 1/4
47 1/4
42 7/8
21 1/2
63
36
~2
~2
3/8
PT 8507 D - measurements in inches
6

64 5/8
3/4
>2
>2 1/8 >2 1/8 42 7/8
21 1/2
26 3/4
36 1/4
63
> 47 1/4
> 47 1/4
3/8
>2
1 7/8
~2
PT 8507 D - measurements in inches
7

PT 8507 D - measurements in millimeters
8

<
PT 8507 D - measurements in millimeters
9

PT 8507 D - measurements in millimeters
10

PT 8507 D - measurements in millimeters
11

PT 8507 D - measurements in millimeters
12

Technical datasheet
Tumble dryer:
Heating:
PT 8507
Steam
Legend: Abbreviations in bold type:
Connection required en - US
Abbreviations in circle with dashes:
Connection optional or required depending on model version
Optional extras:
BS Concrete base Quality and density of concrete must comply with load.
Concrete base must be firmly secured to floor!
Recommended height
4''
100 mm
Minimum height
2''
50 mm
Width min.
48''
1200 mm
Depth min.
44''
1100 mm
DAV Steam
connection
valve
The steam connection valve to regulate the steam supply
must be provided on site.
The following valve can be ordered separately:
Pneumatic Steam Valve (PND)
0– 145 psi 0 – 1000 kPaRegulatable steam pressure
Connection gauge 1/2''
Machine connections:
Electrical
connection
(convertible)
Standard voltage
V
3 AC 208
Frequency
Hz
60
Rated load
kW
1.3
Fuse rating
A
3 × 10
Cable screw connector
M 25
Connection cable
Supplied without
power cord
Convertible to
V
3 AC 220-240V
Frequency
Hz
60
Rated load
kW
1.3
Fuse rating
A
3 × 10
Cable screw connector
M 25
Connection cable
Supplied without
power cord
Installation plan: PT8507 D (Steam Heated)
Date: 2015-06-01 Page: 13

Electrical connection must comply with national regulations.
Connection using multi-pole lockable wall socket in
compliance with IEC/EN 60309 and IEC/EN 60947 is
recommended in order to simplify electrical tests. If
machines are hard-wired, a multi-pole mains switch must be
provided on site. Switches with a contact gap of more than
3 mm can be used. These include switches, fuses and
contactors (IEC/EN 60947). A wall socket or mains isolator
must be easily accessible after installation.
Reinstallation of the supply point, changes to the equipment
or checks on the protective conductor, including
determination of correct fuse rating, should only be
performed by a properly trained electrician.
If necessary, equipotential bonding with good galvanic
contact must be provided in accordance with all appropriate
national and local regulations.
Equipotential
bonding 3/8'' x1 3/8'' 10 mm ×35 mm
Connection with male thread
Connection with washers and nut
M 10
Accessories to be ordered separately
If necessary, equipotential bonding with good galvanic
contact must be provided in accordance with all appropriate
national and local regulations.
Steam
connection
Steam pressure
87 – 145 psi
600 - 1.000 kPa
Boiling point
329 - 363 °F
Steam supply capacity
132 lb/h
Connection thread (on site)
165 – 184 °C
60 kg/h
1/2"internal
thread (NPT)
Steam valve, steam filter and steam stopcock must be
provided on site.
Supply lead steam valve (length). The supply lead for the
electric steam valve is included.
19 11/16'' 500 mm
The steam valve should be installed close to the steam
connection.
Note installation instructions for steam-heated Miele tumble
dryers.
Condensate
connection
Connection thread (on site)
1/2"internal thread
(NPT)
Stopcock and condensate separator to be provided on site.
The condensate drain should be installed such that the
heater banks self-drains when the machine is not in
operation. Consequently, there should be no build-up of
condensate in the heater bank. The installation of bell-
shaped condensate drains is recommended.
Vented
Max. nominal air flow in vented mode
588 cfm
1000 m³/h
Max. permissible pressure loss
0.04 psi
300 Pa
Connection on machine side (ext. diameter)
515/16''
150 mm
Connection pipe provided on site (int. diameter)
515/16''
150 mm
Max. temperature
176 °F 80 °C
As relative humidity inside the vent ducting can be as high
as 100 %, suitable measures must be taken toprevent a
backflow of condensate into the machine.
Air intake
Standard connection: Air intake from installation site
Unobstructed air intake into room recommended
(corresponding to 3 times the vent cross-section of
machine)
83 in² 531 cm²
A sufficient supply of fresh air should be ensured to
replace the air extracted.
Alternative connection: Ducted air intake (from outside
building)
Connector on machine (int. diameter)
65/16''
161 mm
Connection pipe provided on site (ext. diameter)
65/16''
160 mm
Lid removal exposes live components! For safety reasons,
the pipe connected for central air intake should be at least
35 ½” [900 mm] long and secured using two screws.
Installation plan: PT8507 D (Steam Heated)
Date: 2015-06-01 Page: 14

Fittings
(supplied)
Without base
2 × clamps
2 × screws DIN 571 (Ø × length)
1/4'' x 1 9/16'' 6 mm x40 mm
2 × rawl plugs (Ø × length)
3/8'' x2'' 10 mm x50 mm
Machine must be bolted to the floor!
Fixing materials for a floating screed floor are to be provided
on site.
On concrete base
2 × clamps
2 × screws DIN 571 (Ø × length)
1/4'' x 1 9/16'' 6 mm × 40 mm
2 × rawl plugs (Ø × length)
3/8'' x2'' 10 mm × 50 mm
Fixing materials for a floating screed floor are to be provided
on site.
Machine data
Unit width
47 1/2''
1206 mm
Machine depth
40 1/16''
1018 mm
Unit height
64 9/16''
1640 mm
Casing width
47 1/4''
1200 mm
Casing depth
35 15/16''
913 mm
Minimum width of delivery access to installation site
40 9/16''
1030 mm
Recommended rear wall gap (measured to front of machine) 63''
1600 mm
Min. wall gap (to rear edge of lid)
19 11/16''
500 mm
584lb
265 kg
2968 N
2968 N
3071 BTU/h
0.9kW
72.2 dB (A)
72.2 dB (A)
Net weight
Dynamic floor load, max.
Average heat dissipation
(dependent on ambient room temperature and program
selected)
Noise level
Sound pressure level
(measured at a distance of 39 3/8'' [1 m]from the
machine and at aheight of 63'' [1.6 m])
60 dB (A)
60 dB (A)
Installation should onlybe carried out by authorized technicians in accordance with national regulations! Follow installation
instructions when installing machine! All rights reserved!
Installation plan: PT 8507 D (Steam Heated)
Date: 2015-06-02 Page: 15