Miele KM 2355 User manual

Installation Instructions
IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE
Information is subject to change. Please refer to our website to obtain the most
current product specification, technical & warranty information.
To prevent accidents
and appliance damage
read these instructions
before
installation or use.
Technical Service
25

Installation
The minimum distances given in
these Installation instructions are to
combustible surfaces, and must be
observed to ensure safe operation.
Failure to do so increases the risk of
fire.
The cabinetry and venting hood
should be installed first to prevent
damage to the cooktop.
~Gas appliances should only be
installed in a well ventilated area.
~The countertop must be bonded
with heat resistant (212°F/100°C)
adhesive to prevent distortion or
dissolving.
Any wall coverings must be heat
resistant as well.
~This appliance must not be used in
a non-stationary location (e.g. on a
ship).
~Deep fat fryers must not be installed
directly next to gas cooktops. Gas
flames can ignite splattering oil. A
distance of at least 11 3/4" (300 mm)
should be maintained between these
two appliances.
~The cooktop must not be installed
over a dishwasher, washer, dryer,
refrigerator or freezer. Heat radiated by
the cooktop may damage the
appliances.
~Install the appliance so that the
power cord or gas piping does not
come into contact with any portion of
the cooktop which may become hot
during use.
~The power cord and a flexible gas
connection line must be attached in
such a way that they are not in contact
with moving parts of kitchen elements
(e.g. a drawer) and are not subject to
mechanical stress.
~The safety distances listed on the
following pages must be carefully
maintained.
~Never use a sealant unless
expressly stipulated. The sealing tape
of the appliance ensures adequate
sealing to the countertop.
This appliance must be installed
with its own shut off valve and the
included gas pressure regulator.
Both the valve and the regulator
must be easily accessible to the
consumer after the appliance is
installed.
This appliance must be
disconnected from the gas supply
during any pressure testing of the
system performed in excess of ½
psi (3.5 kPa). This appliance must
be isolated at test pressures equal
to or less than ½ psi (3.5 kPa).
Any pipe connections must be
made using a thread sealant
approved for gas connections.
Failure to correctly install these
items could lead to a gas leak and
subsequent explosion.
In Massachusetts installation must
be performed by a licensed
plumber/gas fitter.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS
26

Safety distances above the
appliance
The minimum safety distance given by
the hood manufacturer must be
maintained between the cooktop and
the hood above it. See the installation
instructions of the hood for these safety
measurements.
If the hood manufacturers instructions
are not available or if flammable objects
are installed over the cooktop (e.g.
cabinets, utensil rail, etc.), a minimum
safety distance of 30" (760 mm) must
be maintained.
If there are several appliances
beneath a hood, and they have
different minimum safety distances
always observe the greatest
distance.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS
27

Safety distances
When installing a gas cooktop, there
may be cupboard or room walls of any
size on the rear side and on one side
(right or left) (see illustrations).
The following minimum safety distances
must be maintained:
a2" (50 mm) minimum distance at the
rear of the countertop cutout to the
rear edge of the countertop.
b5 7/8" (150 mm) minimum distance to
the right of the countertop cutout to
an adjacent piece of furniture (e. g.
tall cabinet) or room wall.
c5 7/8" (150 mm) minimum distance to
the left of the countertop cutout to an
adjacent piece of furniture (e. g. tall
cabinet) or room wall.
Not allowed
Recommended
Not recommended
Not recommended
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS
28

aAppliance front
bInstallation height
cGas connection
dPower supply box with connection
cable,L=4ft(1.2 m)
eStepped cut-out for granite or marble
worktops
Please take careful note of the
detailed diagrams for the cut-out
dimensions in granite and marble
countertops.
Installation dimensions
29

Flush mounted gas cooktops are
only suitable for installation in
granite, marble, tiled or solid wood
countertops.
If installing into a countertop made
from any other material, please
check first with the countertop
manufacturer that it is suitable for
installing a flush mounted cooktop.
This appliance requires a 36 7/16"
(900 mm) wide base unit for
installation.
The cooktop must be accessible
from below for servicing purposes
and to ensure that the seal around it
is not dislodged.
The cooktop may be installed:
–in a suitable cut-out in a granite or
marble countertop.
–in a suitable cut-out in a tiled or solid
wood countertop with a wooden
support frame. The frame must be
provided on site, and is not supplied
with the appliance.
Installation
30

Granite and marble countertops
aCountertop
bCooktop
cGap
As the ceramic glass and the
countertop cut-out have a certain
dimensional tolerances, the size of
gap ccan vary.
^Make the countertop cut-out as
shown in "Installation dimensions".
Remember to maintain the minimum
safety distances (see "IMPORTANT
INSTALLATION SAFETY
INSTRUCTIONS").
^Feed the power cord down through
the cut-out.
^Center the cooktop bin the cut-out.
^Connect the cooktop to the mains
(see "Electrical connection").
^Connect the appliance to the gas
supply (see "Gas connection").
^Secure the appliance at the back and
front using the brackets supplied.
See "Securing the appliance".
^Check that the cooktop works.
^Seal the remaining gap cwith a
silicone sealant that is heat-resistant
to at least 320 °F (160 °C).
For granite and marble countertops,
only use silicone sealant that is
especially formulated for granite and
marble, and observe the sealant
manufacturer's instructions.
Installation
31

Solid wood and tiled worktops
aCountertop
bCooktop
cGap
dWooden frame 1/4" (7 mm)
(to be provided on site)
As the ceramic glass and the
countertop cut-out have a certain
dimensional tolerance, the size of
gap ccan vary.
^Make the countertop cut-out as
shown in "Building-in dimensions".
Remember to maintain the minimum
safety distances (see "IMPORTANT
INSTALLATION SAFETY
INSTRUCTIONS").
^Fix the wooden frame d1/16"
(2 mm) below the top edge of the
countertop (see diagram).
^Feed the power cord down through
the cut-out.
^Center the cooktop bin the cut-out.
^Connect the cooktop to the mains
(see "Electrical connection").
^Connect the appliance to the gas
supply (see "Gas connection").
^Secure the appliance at the back and
front using the brackets supplied.
See "Securing the appliance".
^Check that the cooktop works.
^Seal the remaining gap cwith a
silicone sealant that is heat-resistant
to at least 320 °F (160 °C).
Please follow the manufacturer's
instructions.
For granite and marble tiles only
use a silicone sealant that is
specifically formulated for granite
and marble, and observe the
sealant manufacturer's instructions.
Installation
32

Secure the appliance as shown, using
the fixing brackets supplied.
3/4" (20 mm) countertop
1 1/4" (30 mm) countertop
1 1/2" (40 mm) countertop
After installation
Check that all the burners are operating
correctly.
The flame must not go out on the lowest
setting, or when the control is turned
quickly from a high to a low setting.
On the highest setting, the flame must
have a distinctive and visible core.
Securing the appliance
33

This appliance must be grounded
according to local or national codes.
All electrical work should be
performed by a qualified electrician
in accordance with local codes and
with the:
- National Electrical Code
ANSI / NFPA No. 70
for the USA
or
- Canadian Electrical Code Part I
for Canada
(CSA Standard C 22.1).
,WARNING
Disconnect the appliance from the
main power supply before
installation or service. To reduce the
risk of electric shock, make sure that
the appliance is properly grounded
after installation.
Power supply
The automatic ignition requires that the
appliance be connected to a 120 VAC,
60 Hz power supply. The supply line
should be protected by a 15 A fuse.
Actual power consumption (during
ignition only) is 25 W.
This appliance is equipped witha4ft
(1.2 m) long power cord that is ready
for connection to the appropriate outlet.
Place the power outlet so that it is
accessible after the appliance has
been installed in the countertop.
This appliance is equipped with a
three-prong grounding plug to
prevent shock hazards. It should be
plugged directly into a properly
grounded outlet. Do not cut or
remove the grounding prong from
the plug. If the plug does not fit the
outlet, have the proper outlet
installed by a licensed electrician.
To guarantee the electrical safety of
this appliance, continuity must exist
between the appliance and an
effective grounding system. It is
imperative that this basic safety
requirement be met. If there is any
doubt, have the electrical system of
the house checked by a qualified
electrician.
Note to the installer
Please leave these instructions with the
consumer or the appliance.
Electrical connection
34