Miele WT 2679 WPM User manual

Operating instructions
Washer-dryer
WT 2679 WPM
To avoid the risk of accidents
or damage to the machine
it is essential to read
these instructions before it is
installed and used for the first time. M.-Nr. 06 533 690
en-GB

Disposal of the packing material
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Ensure that any plastic wrappings, bags
etc. are disposed safely and kept out of
the reach of babies and young children.
Danger of suffocation!
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if handled
or disposed of incorrectly, could be
potentially hazardous to human health
and to the environment. They are,
however, essential for the correct
functioning of your appliance or
machine. Please do not therefore
dispose of it with your household waste.
Please dispose of it at your local
community waste collection / recycling
centre or contact your Dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
It should be unplugged or disconnected
from the mains electricity supply by a
competent person.
Caring for the environment
2

Caring for the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warning and safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Guide to the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Control panel .....................................................11
Display ..........................................................12
Use.............................................................12
Before using for the first time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Calibrating the load size sensor to zero ..............................14
Washing and drying environmentally . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
WASHING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Brief instructions ..................................................16
Separate washing..................................................16
Extra options .....................................................21
Pre-wash......................................................21
Soak .........................................................21
Short .........................................................21
Water plus .....................................................21
Buzzer........................................................21
Adding or removing laundry after a programme has started.................22
Spinning.........................................................23
Rinse and interim spin ...........................................23
To omit the final spin (Rinse hold)...................................23
To omit rinse and interim spin and the final spin .......................23
Programme chart ..................................................24
Programme sequence ..............................................28
Garment care label symbols .........................................30
Detergent ........................................................30
Water softeners .................................................31
Washing with several components ..................................31
Fabric conditioners or liquid starch .................................32
Automatic dispensing of fabric conditioner or liquid starch to laundry
at the end of a programme ........................................32
Adding fabric conditioner separately ................................32
Adding starch separately .........................................32
Colour run and dye removers / dyes.................................32
DRYING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Separate drying ...................................................33
Contents
3

Extra option ......................................................36
Low temperature ................................................36
Thermospin ....................................................36
Adding or removing laundry after a programme has started.................36
Programme chart ..................................................37
WASHING AND DRYING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Washing and drying in a continuous sequence ..........................41
After each washing or drying programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Rinse out fluff programme.........................................43
Changing the programme sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Cancelling a programme .........................................44
Interrupting a programme.........................................44
Altering a programme ............................................44
Electronic programme locking .....................................45
Delay start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Cleaning the machine ..............................................47
Cleaning the filter in the water inlet ....................................49
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Whattodo,if... ..................................................50
The programme does not start. .......................................50
Fault messages in the display ........................................51
Problems with the load size indicator ..................................52
General problems .................................................53
An unsatisfactory wash result ........................................54
An unsatisfactory drying result .......................................55
The drum door cannot be opened by pressing the Door button..............56
Opening the drum door in the event of a blocked drain outlet and/or
power failure......................................................57
Drain the machine...............................................57
Opening the drum door ..........................................57
Cleaning the drain filter...........................................58
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Future updates (PC) .............................................60
Appliance guarantee ............................................60
Optional accessories ............................................60
Contents
4

Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Frontview........................................................61
Rearview........................................................62
Installation surface .................................................63
Installing the washer-dryer...........................................63
Removing the transit fittings ..........................................63
Levelling the machine ..............................................66
Building under a continous worktop / in a kitchen run ...................67
Fitting a decor panel ...............................................68
Shortening the door panel ...........................................69
Fitting a plinth facing ...............................................70
The Miele water protection system.....................................71
Connection to the water supply .......................................72
Connection to the drainage system ....................................73
Electrical connection U.K. ...........................................74
Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Note for test institutes: ...........................................75
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Settings menu J. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Language J......................................................77
Timeofday ......................................................78
Water plus .......................................................78
Gentle action .....................................................79
Suds cooling .....................................................79
Door release......................................................79
Distribution controller ...............................................80
Alter time ........................................................80
Lock............................................................81
Temperature ......................................................82
Buzzer ..........................................................82
Keypad tones.....................................................82
Display contrast ...................................................82
Display brightness .................................................82
Standby .........................................................83
Memory .........................................................83
Set extended cool-down ............................................83
Contents
5

~It is essential to read these
instructions.
This washer-dryer conforms to
current safety requirements.
Inappropriate use can, however, lead
to personal injury and damage to
property.
To avoid the risk of accidents and
damage to the washer-dryer, please
read these instructions carefully
before using it for the first time. They
contain important information on its
installation, safety, use and
maintenance.
Keep these instructions in a safe
place and ensure that new users are
familiar with the content. Pass them
on to any future owner.
Correct application
~This washer-dryer must only be
used:
–to wash items which are specified by
the manufacturer to be washable on
the care label.
–to dry textiles which have been
washed in a water solution, marked
on the manufacturer's wash care
label as being suitable for tumble
drying. "Dry cleaning kits" for
freshening up garments in a tumble
dryer are increasingly available on
the market. If using, do so at your
own risk, and follow the instructions
provided on the packaging.
Any other applications may be
dangerous. Miele cannot be held liable
for damage resulting from incorrect or
improper use or operation.
~This washer-dryer is not intended for
use by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they are supervised
whilst using it or have been shown how
to use it correctly by a person
responsible for their safety.
Safety with children
~Keep children away from the washer
dryer at all times. It is not a toy! To avoid
the risk of injury do not allow children to
play on or near it or to play with its
controls. Supervise children whilst you
are using it.
~Older children may only use the
washer dryer if its operation has been
clearly explained to them and they are
able to use it safely, recognising the
dangers or misuse.
Warning and safety instructions
6

Technical safety
~Before setting up the washer-dryer,
check it for any externally visible
damage.
Do not install or use a damaged
machine.
~Before connecting the washer-dryer,
ensure that the connection data on the
data plate (voltage and connected
load) match the mains electricity
supply. If in any doubt, consult a
qualified electrician.
~The electrical safety of this
washer-dryer can only be guaranteed
when continuity is complete between it
and an effective earthing system which
complies with current local and national
safety regulations. It is most important
that this basic safety requirement is
present and regularly tested, and where
there is any doubt the household wiring
system should be inspected by a
qualified electrician. The manufacturer
cannot be held liable for the
consequences of an inadequate
earthing system (e.g. electric shock).
~Do not connect the machine to the
mains electricity supply by an extension
lead. Extension leads do not guarantee
the required safety of the washer-dryer
(e.g. danger of overheating).
~Unauthorised repairs could result in
unforeseen dangers for the user, for
which the Miele cannot accept liability.
Repairs should only be undertaken by a
Miele approved service technician.
Ensure current is not supplied to the
machine until after maintenance or
repair work has been carried out.
~In the event of a fault or for cleaning
purposes, the washer-dryer is only
completely isolated from the electricity
supply when:
–it is switched off at the wall socket
and the plug is withdrawn, or
–it is switched off at the mains, or
–the mains fuse is disconnected, or
the screw-out fuse is removed (in
countries where this is applicable).
~The Miele “Water protection system”
protects from water damage provided
the following conditions have been met:
– the machine is correctly plumbed in
and connected to the electricity
supply.
– if a fault has been identified, the
machine must be examined by a
competent person before further use,
and repaired if necessary.
~Faulty components must only be
replaced by genuine Miele original
spare parts. Only when these parts are
fitted can the safety standards of the
machine be guaranteed.
~If the connection cable is faulty it
must only be replaced by a Miele
approved service technician to protect
the user from danger.
Warning and safety instructions
7

~This washer-dryer may only be used
in mobile installations such as ships if a
risk assessment of the installation has
been carried out by a suitably qualified
engineer.
~In countries where there are areas
which may be subject to infestation by
cockroaches or other vermin, pay
particular attention to keeping the
machine and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not be
covered by the guarantee.
~Do not make any alterations to the
washer-dryer, unless authorised to do
so by Miele.
Correct use
~Do not install your washer-dryer in
rooms where temperatures below
freezing may occur. Frozen hoses may
burst or split. The reliability of the
electronic control unit may be impaired
at temperatures below freezing point.
~Before using the washer-dryer for
the first time, check that the transit bars
at the rear of the machine have been
removed (see section on "Installation").
During spinning, a transit fitting which is
still in place may result in damage to
both the machine and adjacent
furniture or appliances.
~Turn off the stopcock if the machine
is to be left for any length of time (e.g.
holiday), especially if there is no floor
drain (gully) in the immediate vicinity.
~Flooding danger.
If hooking the drain hose into a wash
basin, check that the water can drain off
quickly enough to prevent the sink from
overflowing. Make sure the drain hose is
secure, so that the force of the water
flowing out of the hose does not
dislodge it.
~Take care to ensure that foreign
objects (e.g. nails, pins, coins, paper
clips) do not find their way into the
machine with the laundry. These may
damage components of the machine
(e.g. suds container, drum), which in
turn can result in damage to the
laundry.
~If the correct amount of detergent is
dispensed, the machine should not
need to be descaled. If, however, you
do wish to descale the machine only
use proprietary non-corrosive descaling
agents and strictly observe the
instructions on the packaging. A Miele
descaling agent is available to order
(see "Cleaning and care").
Warning and safety instructions
8

~To prevent the risk of fire, the
following must not be dried in this
washer-dryer:
–items which have not been washed.
–items, such as workwear, which have
not been thoroughly cleaned and
which are still soiled with grease, oil
or other desposits (such as
cosmetics, lotions etc).
If items have not been thoroughly
cleaned there is a danger that these
might ignite when heated, even after
they have been removed from the
washer-dryer at the end of the
programme.
– items which have been treated with
inflamable cleaning agents or
contain residues of acetone, alcohol,
benzine, petrol, stain remover,
turpentine, wax, wax remover or other
chemicals (e.g. mops and floor
cloths).
– items which have been splashed with
hair lacquer, hair spray, nail varnish
remover or similar substances.
When washing such heavily soiled
items, ensure that you use sufficient
detergent and select a high
temperature. If in doubt, wash the
items several times.
~To prevent the risk of fire, the
following must not be dried in this
washer-dryer:
–fabrics which contain a large
proportion of rubber, foam rubber or
rubber-like materials. For example,
products made from latex foam
rubber, shower caps, waterproof
textiles, rubberised articles and items
of clothing and pillows with foam
rubber filling.
–items which contain padding or
fillings (e.g. pillows, jackets). If these
were damaged the filling could get
out with the risk of igniting in the
washer-dryer.
~In many programmes, the heating
phase is followed by a cooling down
phase to ensure that the items are not
too hot to handle when you remove
them (this also avoids the danger of the
laundry self-igniting). The programme is
not finished until the cooling down
phase has been completed.
Ensure that you always wait until the
end of the programme before removing
the laundry.
~Warning: Do not switch the
washer-dryer off before the end of a
drying programme. If this was done and
the laundry was then removed immedi-
ately it could give off a great amount of
heat.
~Fabric conditioner and similar
products must be used according to
the instructions on the manufacturer's
packaging.
Warning and safety instructions
9

~Only use dyes specified by the
manufacturer as being suitable for use
in a domestic washing machine. Always
observe the manufacturer's instructions
carefully.
~Colour run and dye removers
contain sulphur compounds which can
cause damage such as corrosion. Do
not use these products in this machine.
~Make sure that any dispensing balls
etc. are removed from laundry before
the drying programme. These
dispensers can melt during the drying
programme and cause damage to the
machine and the laundry. Do not use
liquid dispenser balls or similar if you
are planning to wash and then dry in
one continuous sequence.
~Textiles which have been pre-treated
in solvent based cleaning agents must
be thoroughly rinsed in clean water
before being washed in the
washer-dryer.
~Never use solvent based cleaning
agents, e.g. those containing benzene,
in this machine, as this may result in
damage to component parts and create
toxic fumes. Such agents also pose a
fire and explosion hazard.
~Take care, the metal cap is hot
after drying.
Open the door wide after the drying
cycle. Do not touch the metal cap
located on the inside of the door glass.
It will still be hot and could cause a
burn.
Accessories
~Accessory parts may only be fitted
when expressly approved by Miele. If
other parts are used, guarantee,
performance and product liability
claims will be invalidated.
Miele cannot be held liable for
damage caused by non-compliance
with these Warning and Safety
instructions.
Warning and safety instructions
10

Control panel
aStart/Stop button
For starting the programme selected
and cancelling a programme once it
has started.
bDisplay with–,OK,+and
Load/Detergent buttons
See the following page for more
details.
cmbutton
For selecting delay start and
setting the time of day.
dPC / Optical interface
This is used by service technicians to
run diagnostic checks on your
machine and can also be used to
update programming data in the
future.
eExtra option buttons
with indicator lights
Various extra options can be added
to the programmes.
fProgramme selector
For selecting washing and drying
programmes. The programme
selector can be turned clockwise or
anti-clockwise.
gWashing/Drying button
for selecting:
– Washing
– Drying
– Washing and Drying.
hI-On/0-Off button
For switching the washer-dryer on
and off.
iDoor button
Opens the machine door.
Guide to the machine
11

Display
When a programme is selected the
display can be used to select and
change programme parameters.
- / + buttons
For altering the parameters highlighted
in the display:
-decreases the parameter or moves
the highlighting upwards
+increases the parameter or moves
the highlighting downwards.
OK button
For confirming the parameter selected
and choosing the next parameter.
Load/Detergent button
For calling up the load size and the
detergent amount.
With the programme selector at the
Further programmes position, you can
select the following programmes via the
display: Dark garments,Shirts,Denim,
Sportswear,Outerwear,Proofing,
Curtains,Separate rinse and Starch.
Delay start and the soak time are
selected via the display.
The display shows the duration of the
programmes and the current time of
day.
The Settings Jmenu is also operated
via the display.
Use
This washer-dryer can be used:
–to wash separately
max. load 5 kg (depending on
programme);
–to dry separately
max. load 2.5 kg (depending on
programme);
or
–to wash and dry in a continuous
sequence
max. load 2.5 kg (depending on
programme).
Guide to the machine
12

Before using the machine for the first
time ensure that it is correctly
installed and connected. See
"Installation and connection". Also
check that the drain filter is securely
tightened to prevent the risk of water
leaks during use.
The washer-dryer has a sensor which
measures the amount of laundry in the
drum. This determines the amount of
detergent required. To allow the load
size indicator to function correctly, you
must first run a wash programme
without any laundry and without
detergent.
^Open the stopcock.
^Press the I-On/0-Off button in.
If the washer-dryer is being switched on
for the first time, the welcome screen
will appear.
M
Willkommen
The welcome screen will not appear
again once a programme lasting
longer than 1 hour has been
completed.
After a few seconds the display will
change to show the screen for selecting
your language.
Setting the language
Cèeština
Fdansk
deutsch H
^Use the –and +buttons to select the
language you want and confirm your
selection by pressing the OK button.
Setting the time of day
The display for setting the time will
appear.
12:00
Set the time
^Set the hour with the –and +buttons
and confirm your setting by pressing
the OK button. Now set the minutes.
After you have confirmed the minute
setting, the display will change to
show the reminder to remove the
transport struts.
Before using for the first time
13

Reminder to remove transport struts
To avoid the risk of damage, the
transport struts must be removed
before the washer-dryer is used for
the first time. See "Installation and
connection" for instructions on how
to do this.
iRemove transport
struts
OK
^After removing the transport struts (if
this has not already been done by
your fitter) press the OK button.
Running your first programme
Your washer-dryer is now ready for the
first programme to be run.
15:00
Select programme
^Turn the programme selector to the
Cottons position.
^Press the Start/Stop button.
^When the programme has finished,
turn the programme selector to Stop
and switch off the washer-dryer.
The load sensor must then be
calibrated to zero as you would with
bathroom scales.
Calibrating the load size sensor to
zero
^Switch the machine on.
^Open the drum door.
^Turn the programme selector to the
Cottons position.
^Press and hold the Load/Detergent
button pressed in until the following
message appears in the display:
iZero setting
OK
^Turn the programme selector to Stop
and switch off the washer-dryer.
The machine is now ready for use.
Before using for the first time
14

Energy and water consumption
–Water consumption and energy
usage are determined by the size of
the load.
To make the most out of your
machine, load the maximum dry load
for the programme you are using.
–Use the Automatic and Express
programmes for small loads.
–When smaller amounts of laundry are
washed using the Cottons
programmes, the automatic load
recognition system will reduce the
amount of water, time and energy
used. This may mean that the
programme duration is adjusted
during the course of the wash
programme.
– Using the Cottons 60°C programme
instead of the Cottons 95°C
programme will give energy savings
of between 35% and 45%. This is
sufficient for most levels of soiling.
For stubborn or old stains, use the
Soak extra option.
Detergent
–Do not exceed the amounts of
detergent recommended by the
manufacturer on the packaging.
–Reduce the amount of detergent for
smaller loads. Use the Load/
Detergent button.
Choosing the correct extra option
(Pre-wash, Soak, Short)
Select:
A wash programme together with the
Short extra option for light to normal
soiling where there are no obvious
marks.
A wash programme without any extra
options for normal to heavy soiling.
A wash programme together with the
Soak option for heavily soiled
laundry.
– Use the extra option Soak instead of
Pre-wash. If Soak is followed immedi-
ately by a main wash, the same suds
are used.
When drying straight afterwards
–Select a high spin speed for the
wash programme, as well as for the
Thermospin, if tumble drying this
laundry afterwards. This saves time
and energy.
Washing and drying environmentally
15

Brief instructions
The headings numbered A,B,C,...
show the operating sequence and can
be used as brief instructions.
Separate washing
ASort the laundry
^Empty all pockets.
,Foreign objects (e.g. nails, coins,
paper clips, etc.) can cause damage
to garments and components in the
machine.
^Badly soiled areas, stains etc. should
be cleaned as soon as possible,
preferably whilst still fresh. Spillages
should be carefully dabbed off using
a soft colourfast cloth. Do not rub!
Badly soiled areas can be pre-treated
with liquid detergent, stain removers
etc. first, following the manufacturer's
instructions. With particularly stubborn
stains ask your dry cleaner for advice.
,Do not use solvent-based
cleaning agents in this machine.
^Sort the laundry by colour and by
care label. Most garments have a
textile care label in the collar or side
seam.
Dark textiles often contain excess dye
and should be washed separately
several times before being included in a
mixed load. Always wash whites and
coloureds separately.
–Curtains: Remove lead weights first
or place in a laundry bag.
–Underwiring and collar stiffeners: Any
loose wiring in bras, shirt collar
stiffeners, etc. should be removed or
sewn in.
– Knitted garments, trousers and jeans,
T-shirts and sweat shirts: Turn inside
out, if recommended by the
manufacturer.
– Close any zips, fasten hooks and
eyes etc before washing.
– Fasten duvet covers and pillow cases
to prevent small items from being
trapped inside them.
Do not wash any items in this machine
which are specified by the
manufacturer as non-machine
washable on the care label. (h
symbol)
WASHING
16

BSwitch the machine on
The interior drum lighting will come on.
CSelect a programme
^Select the programme you want.
The programme selected will appear in
the display.
Minimum iron
Further programmes:
When you turn the programme selector
to Further programmes, a list of these
programmes will appear in the display.
EDark garments
Denim
Shirts H
^Use the -or +button to highlight the
programme you wish to select and
confirm your selection by pressing
the OK button.
Wait until the display switches to show
the menu for the programme selected.
40°C 900 rpm
Duration: 1:00 h
or
Denim
40°C 900 rpm
Duration: 1:00 h
^Press the Washing/Drying button
repeatedly until only the Washing
indicator light is lit up.
The Drying indicator light must not
be lit up as well as this would mean
that the washing programme would
be followed immediately by the
drying programme.
^You can alter the highlighted
temperature with the -or +buttons.
Press the OK button to confirm the
temperature you want and move on to
the spin speed.
30°C 900 rpm
Duration 0:57 h
^You can then alter the highlighted
spin speed, select rinse hold or
without spin with the -or +buttons.
WASHING
17

^You can select any extras options
with the extra option buttons.
^Each press of the top right hand
button selects the extra option in the
following order: Pre-wash or Soak or
no option is selected.
Not all the extra options are suitable for
use with every wash programme.
You can only select extra options which
are compatible with the basic
programme being used.
The Low temperature extra only
applies to drying.
^Select Delay start, if required.
DLoad the drum
^Press the Door button to open the
drum door.
The load size indicator display will
appear.
Load <25%
B
The display shows the amount of
laundry loaded in the drum asa%(in
25% steps) of the maximum load
permissible for the programme
selected.
^Unfold the laundry and load loosely
in the drum. Mixing both large and
small items gives better wash results
and also helps distribute the load
evenly during spinning.
The most efficient use of energy and
water is achieved when a full load is
washed. However, do not overload as
this causes creases and reduces
cleaning efficiency.
Make sure that no garments are
caught between the drum door and
seal.
^Shut the door with a gentle swing.
WASHING
18

EAdd detergent
The load size indicator display will be
replaced with the detergent percentage
display.
Detergent 75%
A
40% Add slightly less than half the
amount recommended . . .
50% Add half the amount
recommended . . .
60% Add slightly more than half the
amount recommended . . .
75% Add three quarters of the
amount recommended . . .
100% Add the full amount
You also need to take the level of soiling
and water hardness into account.
too little detergent results in:
–Laundry not getting properly clean
and with time it may become grey
and hard to the touch.
–Greasy particles clinging to the
laundry.
–Limescale deposits on the heater
elements.
too much detergent results in:
–Excessive foam which causes a low
level of agitation and poor wash,
rinse and spin results.
–High water consumption (an
additional rinse cycle will
automatically switch in).
–A burden to the environment.
^Pull out the detergent drawer and add
detergent to the compartments as
follows:
i= Detergent for the pre-wash
(1/4of the total amount
recommended). This
compartment is also used for
starch formulations when
starching separately.
j= Detergent for the main wash
including Soak
§= Fabric conditioner or liquid
starch
^Close the detergent drawer.
See "Detergent" for further information.
WASHING
19

FStart the programme
^Press the flashing Start/Stop button.
The estimated programme duration will
count down in the display in one minute
steps. During the first 10 minutes the
machine measures how much water is
being absorbed by the laundry. The
programme duration may be longer or
shorter depending on this absorbency
rate.
The programme sequence is also
shown in the display. The washer-dryer
shows you when each section of the
programme is reached.
The drum lighting switches off once the
programme has started.
GRemove the laundry when the
programme has finished
In the anti-crease phase after the
programme has finished, the following
will appear alternately in the display:
Anti-crease
and
iProgramme finished.
Remove laundry, then
switch the machine off.
^Turn the programme selector to the
Stop position. Press the Door button
to open the drum door.
^Remove the laundry.
Only remove laundry from the
machine once the drum has stopped
turning. Reaching into a moving
drum is extremely dangerous and
could result in injury.
Check that all items have been
removed from the drum. Items left in
the drum could discolour other items
in the next wash or become
discoloured themselves.
Important! Always remove the
laundry before switching the machine
off. This is important to ensure that
the load size indicator works
correctly.
^Switch the machine off with the I-On/
0-Off button.
See "After each washing or drying
programme" for further information.
After washing a full load
If you have washed a full load of
laundry and you wish to dry the
laundry in the washer-dryer
afterwards you will have to remove
half the load. Carry out the drying
procedure in two batches.
WASHING
20