Miele WT 2780 User manual

Operating instructions
Washer-dryer
WT 2780
To avoid the risk of accidents
or damage to the machine
it is essential to read
these instructions before it is
installed and used for the first time. M.-Nr. 07 661 240
en-GB

Disposal of the packing material
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Ensure that any plastic wrappings,
bags etc. are disposed safely and kept
out of the reach of babies and young
children. Danger of suffocation!
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
Please dispose of it at your local
community waste collection / recycling
centre or contact your Dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
It should be unplugged or disconnected
from the mains electricity supply by a
competent person.
Caring for the environment
2

Caring for the environment..........................................2
Warning and safety instructions .....................................6
Guide to the machine .............................................11
Control panel .....................................................11
Display ..........................................................12
Use.............................................................12
Before using for the first time.......................................13
Calibrating the load size sensor to zero ..............................14
Washing and drying environmentally and economically.................15
WASHING .......................................................16
Short instructions ..................................................16
Separate washing .................................................16
Extra options .....................................................21
Short .........................................................21
Water plus.....................................................21
Stains ........................................................21
Further extras.....................................................21
Extra quiet.....................................................21
Extra rinse .....................................................22
Pre-wash ......................................................22
Soak .........................................................22
Rinse hold .....................................................22
Adding or removing laundry after a programme has started ................22
Final spin speed ..................................................23
Rinse and interim spin ...........................................23
To omit the final spin (Rinse hold) ..................................23
To omit the spin between rinses and the final spin .....................23
Programme chart ..................................................24
Programme sequence ..............................................28
Garment care label symbols .........................................30
Detergent ........................................................31
Water softeners.................................................32
Washing with several components ..................................32
Fabric conditioner and liquid starch.................................33
Colour run and dye removers/dyes .................................33
DRYING .........................................................34
Separate drying ...................................................34
Contents
3

Extras ...........................................................37
Low temperature................................................37
Thermospin ....................................................37
Adding or removing laundry after a programme has started ................37
Programme chart ..................................................38
WASHING AND DRYING ...........................................43
Washing and drying in a continuous sequence ..........................43
After each washing or drying programme...............................44
Rinse out fluff programme .........................................45
Changing the programme sequence .................................46
To cancel a programme ..........................................46
Interrupting a programme.........................................46
Changing a programme ..........................................46
Safety lock ....................................................47
Delay start.......................................................48
Cleaning and care ................................................49
Cleaning the machine ..............................................49
Cleaning the filter in the water inlet ....................................51
Problem solving guide ............................................52
The programme does not start. .......................................52
A fault message appears in the display ................................53
Problems with the load size indicator ..................................54
General problems .................................................55
An unsatisfactory wash result ........................................56
An unsatisfactory drying result .......................................57
The drum door cannot be opened by pressing the Door button..............58
Opening the drum door in the event of a blocked drain outlet and/or
power failure .....................................................59
After sales service ................................................61
Future updates (PC) .............................................61
Appliance guarantee ............................................61
Optional accessories ............................................61
Installation and connection ........................................62
Front view........................................................62
Rear view ........................................................63
Contents
4

Installation surface.................................................64
Installing the washer-dryer ..........................................64
Removing the transit fittings .........................................64
Levelling the machine ..............................................66
Screwing out and adjusting the feet .................................67
Building under a continous worktop / in a kitchen run ...................67
The Miele water protection system ....................................68
Connection to the water supply .......................................69
Connection to the drainage system....................................70
Electrical connection U.K. ...........................................71
Consumption data ................................................72
Notes for test institutes: ..........................................72
Technical data ...................................................73
Settings menu ...................................................74
Language J......................................................74
Buzzer ..........................................................74
Time ............................................................75
Temperature unit ..................................................75
Brightness / Contrast ...............................................75
Standby display ...................................................75
Keypad tone .....................................................75
Lock code .......................................................76
Memory .........................................................76
Longer pre-wash Cottons ...........................................77
Gentle action .....................................................77
Suds cooling .....................................................77
Distribution controller...............................................77
Drying levels .....................................................78
Extended cool down ...............................................78
Door lock ........................................................78
Anti-crease.......................................................78
Optional accessories..............................................79
CareCollection ....................................................79
Contents
5

~It is essential to read these
instructions.
This washer-dryer conforms to
current safety requirements.
Inappropriate use can, however,
lead to personal injury and damage
to property.
To avoid the risk of accidents and
damage to the washer-dryer, please
read these instructions carefully
before using it for the first time. They
contain important information on its
installation, safety, use and
maintenance.
Keep these instructions in a safe
place and ensure that new users are
familiar with the content. Pass them
on to any future owner.
Correct application
~This washer-dryer is not designed
for commercial use. It is intended for
use in domestic households and in
similar working and residential
environments such as:
–Shops
–Offices and showrooms
and by residents in establishments
such as
–Hostels and guest houses
~It must only be used as a domestic
appliance to
–wash items which are specified by
the manufacturer as being washable
on the care label.
–dry items which have been washed
in a water solution and which are
marked on the manufacturer's care
label as being suitable for tumble
drying. "Dry cleaning kits" for
freshening up garments in a tumble
dryer are increasingly available on
the market. If using, do so at your
own risk, and follow the instructions
provided on the packaging.
Any other usage is not supported by
the manufacturer and could be
dangerous. Miele cannot be held liable
for damage resulting from incorrect or
improper use or operation of the
washer-dryer.
~This washer-dryer is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience and knowledge, unless they
are supervised whilst using it or have
been shown how to use it correctly by a
person responsible for their safety.
Safety with children
~Keep children away from the
washer-dryer at all times. It is not a toy!
To avoid the risk of injury do not allow
children to play on or near it or to play
with its controls. Supervise children
whilst you are using it.
~Older children may only use the
washer-dryer if its operation has been
clearly explained to them and they are
able to use it safely, recognising the
dangers or misuse.
Warning and safety instructions
6

Technical safety
~Before setting up the washer-dryer,
check it for any externally visible
damage.
Do not install or use a damaged
machine.
~Before connecting the washer-dryer,
ensure that the connection data on the
data plate (voltage and connected
load) match the mains electricity
supply. If in any doubt, consult a
qualified electrician.
~The electrical safety of this
washer-dryer can only be guaranteed
when continuity is complete between it
and an effective earthing system which
complies with current local and national
safety regulations. It is most important
that this basic safety requirement is
present and regularly tested, and
where there is any doubt the household
wiring system should be inspected by a
qualified electrician. The manufacturer
cannot be held liable for the
consequences of an inadequate
earthing system (e.g. electric shock).
~Do not connect the machine to the
mains electricity supply by an extension
lead. Extension leads do not guarantee
the required safety of the washer-dryer
(e.g. danger of overheating).
~Unauthorised repairs could result in
unforeseen dangers for the user, for
which the Miele cannot accept liability.
Repairs should only be undertaken by a
Miele approved service technician.
Ensure current is not supplied to the
machine until after maintenance or
repair work has been carried out.
~In the event of a fault or for cleaning
purposes, the washer-dryer is only
completely isolated from the electricity
supply when:
–it is switched off at the wall socket
and the plug is withdrawn, or
–it is switched off at the mains, or
–the mains fuse is disconnected, or
the screw-out fuse is removed (in
countries where this is applicable).
~This washer-dryer must only be
connected to the on-site water supply
using a new hose kit. Old hoses must
not be re-used.
~Faulty components must only be
replaced by genuine Miele original
spare parts. Only when these parts are
fitted can the safety standards of the
machine be guaranteed.
~If the connection cable is faulty it
must only be replaced by a Miele
approved service technician to protect
the user from danger.
Warning and safety instructions
7

~This washer-dryer may only be used
in mobile installations such as ships if a
risk assessment of the installation has
been carried out by a suitably qualified
engineer.
~In countries where there are areas
which may be subject to infestation by
cockroaches or other vermin, pay
particular attention to keeping the
machine and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not be
covered by the guarantee.
~Do not make any alterations to the
washer-dryer, unless authorised to do
so by Miele.
Correct use
~Do not install your washer-dryer in
rooms where temperatures below
freezing may occur. Frozen hoses may
burst or split. The reliability of the
electronic control unit may be impaired
at temperatures below freezing point.
~Before using the washer-dryer for
the first time, check that the transit bars
at the rear of the machine have been
removed (see section on "Installation
and connection"). During spinning, a
transit fitting which is still in place may
result in damage to both the machine
and adjacent furniture or appliances.
~Turn off the stopcock if the machine
is to be left for any length of time (e.g.
holiday), especially if there is no floor
drain (gully) in the immediate vicinity.
~Flooding danger.
If hooking the drain hose into a wash
basin, check that the water can drain
off quickly enough to prevent the sink
from overflowing. Make sure the drain
hose is secure, so that the force of the
water flowing out of the hose does not
dislodge it.
~Take care to ensure that foreign
objects (e.g. nails, pins, coins, paper
clips) do not find their way into the
machine with the laundry. These may
damage components of the machine
(e.g. suds container, drum), which in
turn can result in damage to the
laundry.
~If the correct amount of detergent is
dispensed, the machine should not
need to be descaled. If, however, you
do wish to descale the machine only
use proprietary non-corrosive descaling
agents and strictly observe the
instructions on the packaging. A
special descaling agent is available to
order from the Miele Spare Parts
Department or via the internet at
www.miele-shop.com.
Warning and safety instructions
8

~To prevent the risk of fire, the
following must not be dried in this
washer-dryer:
–items which have not been washed.
–items, such as workwear, which have
not been thoroughly cleaned and
which are still soiled with grease, oil
or other deposits (such as
cosmetics, lotions etc).
If items have not been thoroughly
cleaned there is a danger that these
might ignite when heated, even after
they have been removed from the
washer-dryer at the end of the
programme.
– items which have been treated with
inflammable cleaning agents or
which contain residues of acetone,
alcohol, benzine, petrol, stain
remover, turpentine, wax and wax
remover or other chemicals (e.g.
mops and floor cloths).
– items which have been splashed with
hair lacquer, hair spray, nail varnish
remover or similar substances.
When washing such heavily soiled
items, ensure that you use sufficient
detergent and select a high
temperature. If in doubt, wash the
items several times.
~To prevent the risk of fire, the
following must not be dried in this
washer-dryer:
–items which have been cleaned
using chemicals (e.g. professional
dry-cleaning agents).
–fabrics which contain a large
proportion of rubber, foam rubber or
rubber-like materials. For example,
products made from latex foam
rubber, shower caps, waterproof
textiles, rubberised articles and items
of clothing and pillows with foam
rubber filling.
– damaged items which contain
padding or fillings (e.g. pillows,
jackets). When damaged, the filling
can get out with the risk of igniting in
the washer-dryer.
~In many programmes, the heating
phase is followed by a cooling down
phase to ensure that the items are not
too hot to handle when you remove
them (this also avoids the danger of the
laundry self-igniting). The programme is
not finished until the cooling down
phase has been completed.
Ensure that you always wait until the
end of the programme before removing
the laundry.
~Warning: Do not switch the
washer-dryer off before the end of a
drying programme. If this was done
and the laundry was then removed
immediately it could give off a great
amount of heat.
~Fabric conditioner and similar
products must be used according to
the instructions on the manufacturer's
packaging.
Warning and safety instructions
9

~Only use dyes specified by the
manufacturer as being suitable for use
in a domestic washing machine. Always
observe the manufacturer's instructions
carefully.
~Colour run and dye removers
contain sulphur compounds which can
cause damage such as corrosion. Do
not use these products in this machine.
~Make sure that any dispensing balls
etc. are removed from laundry before
the drying programme. These
dispensers can melt during the drying
programme and cause damage to the
machine and the laundry. Do not use
liquid dispenser balls or similar if you
are planning to wash and then dry in
one continuous sequence.
~Textiles which have been
pre-treated in solvent based cleaning
agents must be thoroughly rinsed in
clean water before being washed in the
washer-dryer.
~Never use solvent based cleaning
agents, e.g. those containing benzene,
in this machine, as this may result in
damage to component parts and create
toxic fumes. Such agents also pose a
fire and explosion hazard.
~Take care, the metal cap is hot
after drying.
Open the door wide after the drying
cycle. Do not touch the metal cap
located on the inside of the door glass.
It will still be hot and could cause a
burn.
Accessories
~Accessory parts may only be fitted
when expressly approved by Miele. If
other parts are used, guarantee,
performance and product liability
claims will be invalidated.
Miele cannot be held liable for
damage caused by non-compliance
with these Warning and Safety
instructions.
Warning and safety instructions
10

Control panel
aStart/Stop button
For starting the programme selected
and cancelling a programme once it
has started.
bDisplay with X,OK and Ybuttons
See the following page for more
information.
c+button
For selecting delay start.
dPC / Optical interface
This is used by Miele service
technicians during servicing work for
testing purposes.
eLoad % / Detergent % button
For displaying the load size or the
recommended amount of detergent,
and for calibrating the load size
sensor to zero.
fExtra option buttons
gProgramme selector
For selecting washing and drying
programmes.
hWashing/Drying button
for selecting:
– Washing
– Drying
– Washing and Drying.
iKbutton
For switching the washer-dryer on
and off.
To save energy, the machine will
switch itself off automatically 15
minutes after the end of the
programme/anti-crease phase or
after being switched on if no other
selection is made.
jDoor button
Opens the machine door.
11
Guide to the machine

Display
The display is operated using the X,
OK and Ybuttons. The value or option
currently selected will appear
highlighted.
Press button X
to decrease a value in the display or to
scroll down to the next option.
Press button Y
to increase a value in the display or to
scroll up to the next option.
Press the OK button
to confirm the value or option
highlighted in the display.
With the programme selector at the
Further programmes / Settings position,
you can change display settings (see
"Settings menu") and select the
additional programmes (see
"Programme chart").
The display is also used for selecting
the wash temperature, spin speed,
soak duration, delay start, safety lock
and to cancel a programme.
Use
This washer-dryer can be used:
–to wash separately
Maximum load (depending on
programme) 5.5 kg;
–to dry separately
Maximum load (depending on
programme) 3.0 kg;
or
–to wash and dry in a continuous
sequence
Maximum load (depending on
programme) 3.0 kg;
Guide to the machine
12

Before using the machine for the first
time ensure that it is correctly
installed and connected. Also check
that the drain filter is securely
tightened to prevent the risk of water
leakage during use. See "Installation
and connection".
This washer-dryer has undergone a
complete functional test at the factory
and there will be some residual water
in the drum from this process.
The washer-dryer has a sensor which
measures the amount of laundry in the
drum. This determines the amount of
detergent required. To allow the load
size indicator to function correctly, you
must first run a wash programme
without any laundry and without
detergent.
^Open the stopcock.
^Press the Kbutton.
If the machine is being switched on for
the first time, the Miele Willkommen
welcome screen will appear.
The welcome screen will not appear
again once a programme lasting
longer than 1 hour has been
completed.
After a few seconds the display will
change to show the screen for
selecting your language.
Setting the language
Language
deutsch ;
english ,
^Use the Xand Ybuttons to select
the language you want and confirm
your selection by pressing the OK
button.
Setting the time of day
The display for setting the time will then
appear.
Time
12:00
^Set the hour with the Xand Ybuttons
and confirm your setting by pressing
the OK button. Then do the same to
set the minutes.
After you have confirmed the minute
setting, the display will change to show
the reminder to remove the transport
bars.
Reminder to remove transport bars
,To avoid the risk of damage, the
transport bars must be removed
before the washer-dryer is used for
the first time. See "Installation and
connection" for instructions on how
to do this.
^After removing the transport bars (if
this has not already been done by
your fitter) press the OK button.
Before using for the first time
13

Running your first programme
Your washer-dryer is now ready for the
first programme to be run.
^Turn the programme selector to
Cottons.
^Press the Start/Stop button.
^At the end of the programme switch
the machine off.
After running the first programme, the
load sensor has to be calibrated to
zero (as you would with bathroom
scales).
Calibrating the load size sensor to
zero
^Switch the machine on.
^Open the drum door.
^Turn the programme selector to
Cottons.
^Press and hold the Load % /
Detergent % button in until the
following message appears in the
display:
Zero setting OK
^Switch the machine off.
The machine is now ready for use.
Before using for the first time
14

Energy and water consumption
–Water consumption and energy
usage are determined by the size of
the load.
To make the most out of your
machine, load the maximum amount
for the programme you are using.
–Use the Automatic plus and Express
20 programmes for small loads.
–When smaller amounts of laundry are
washed using the Cottons
programmes, the automatic load
recognition system will reduce the
amount of water, time and energy
used. This may mean that the time
left shown in the display is adjusted
during the course of the wash
programme.
– Using the Cottons 60°C programme
instead of the Cottons 95°C
programme will give energy savings
of between 35% and 45%. This is
sufficient for most levels of soiling.
For stubborn or old soiling use the
Soak extra option.
Detergent
–Do not exceed the amounts of
detergent recommended by the
manufacturer on the packaging.
–Reduce the amount of detergent for
smaller loads. Use the Load % /
Detergent % button.
Choosing the correct extra option
(Pre-wash, Soak, Short)
Select:
–A wash programme together with the
Short extra option for light to normal
soiling where there are no obvious
marks.
– A wash programme without any extra
options for normal to heavy soiling.
– A wash programme together with the
Soak extra option for very heavily
soiled laundry.
– The Pre-wash extra option for laundry
with large amounts of dirt (e.g. dust,
sand).
When drying straight after washing
Select a high spin speed for the wash
programme, as well as for the
Thermospin to save time and energy.
Washing and drying environmentally and economically
15

Short instructions
The headings numbered A,B,C,...
show the operating sequence and can
be used as brief instructions.
Separate washing
ASort the laundry
^Empty all pockets.
,Foreign objects (e.g. nails,
coins, paper clips, etc.) can cause
damage to textiles and to
components in the machine.
^Badly soiled areas, stains etc. should
be cleaned as soon as possible,
preferably whilst still fresh. Spillages
should be carefully dabbed off using
a soft, colourfast cloth. Do not rub!
Badly soiled areas can be pre-treated
with liquid detergent, stain removers
etc. first, following the manufacturer's
instructions. You can also use the
"Stains" extra option. With particularly
stubborn stains ask your dry cleaner for
advice.
,Do not use solvent-based
cleaning agents in this machine.
^Sort the laundry by colour and by
care label. Most garments have a
textile care label in the collar or side
seam.
Curtains: Remove lead weights first or
place in a laundry bag.
–Underwiring and collar stiffeners:
Any loose wiring in bras, shirt collar
stiffeners, etc. should be removed or
sewn in.
– Close any zips, fasten hooks and
eyes etc before washing.
– Wash light and dark coloured items
separately.
– Fasten duvet covers, pillow cases
etc. to prevent small items from
being rolled up inside them.
Do not wash items in this machine
which are specified by the
manufacturer as not washable on the
care label.
WASHING
16

BSwitch the machine on
The interior drum lighting will come on.
The drum lighting will go out
automatically after five minutes. Press
the Door button to switch the drum
lighting back on again.
CSelect a programme
^Select the programme you want.
The programme selected will appear in
the display.
Cottons
60°C 1600 rpm
Duration: 1:49 h
Further programmes:
Turn the programme selector to Further
programmes/Settings to display a list of
other programmes that the machine
has to offer.
Further programmes
Settings !;
Dark garments ,
^Use the Xor Ybutton to highlight the
programme you wish to select and
confirm your selection by pressing
the OK button.
^Press the Washing/Drying button
repeatedly until only the Washing
indicator light is lit up.
The Drying indicator light must not
be lit up as well as this would mean
that the washing programme would
be followed immediately by the
relevant drying programme.
Cottons
60°C 1600 rpm
Duration: 1:49 h
^Use the Xor Ybutton to alter the
temperature. Press the OK button to
confirm the temperature selected and
move on to the spin speed option.
Cottons
40°C 1600 rpm
Duration: 2:04 h
^Use the Xor Ybutton to alter the
spin speed or to select No spin
(No .).
WASHING
17

DSelect Extra option(s)
^Press the appropriate button to select
Short or Water plus. The relevant
indicator light will come on.
^Then select any Further extras or the
Stains option:
Example:
Further extras
8Extra quiet ;
8Extra rinse ,
^Use the Xor Ybutton to highlight the
Extra you wish to select and confirm
your selection by pressing the OK
button.
A tick 9will appear to show which
Extra has been selected. If you wish to
deselect the Extra with a tick against it
press the OK button again.
Press the Further extras button again
to come out of the Extras menu.
You can only select extra options which
are compatible with the programme
being used. If the Extras or Stains
option cannot be selected it is not
compatible with the programme you are
trying to use it with.
The Low temperature option is only
available for a drying programme.
ELoad the drum
^Press the Door button to open the
drum door.
The load size indicator display will
appear.
Load
8< 25%
The display shows the amount of
laundry loaded in the drum asa%(in
25% steps) of the maximum load
permissible for the programme
selected.
^Unfold the laundry and load loosely
into the drum. Mixing both large and
small items gives better wash results
and also helps distribute the load
evenly during spinning.
The most efficient use of energy and
water is achieved when a full load is
washed. However, do not overload as
this causes creases and reduces
cleaning efficiency.
Make sure that no items are caught
between the drum door and seal.
^Shut the door with a gentle swing.
WASHING
18

FAdd detergent
The detergent dispenser display will
now appear.
Detergent
7100%
The percentage shown relates to the
amount of detergent recommended by
the manufacturer on the packaging.
40% Add slightly less than half the
recommended amount...
50% Add half the recommended
amount...
60% Add slightly more than half the
recommended amount...
75% Add three quarters of the
recommended amount...
100% Add the recommended amount
You also need take the level of soiling
and water hardness into account.
Too little detergent results in:
–Laundry not getting properly clean
and with time it may become grey
and hard to the touch.
–Greasy particles clinging to laundry.
–Limescale deposits on the heater
elements.
Too much detergent results in:
–Excessive foam which causes a low
level of agitation and poor wash,
rinse and spin results.
–High water consumption (an
additional rinse cycle will
automatically switch in).
–A burden to the environment.
^Pull out the detergent drawer and
add detergent to the compartments
as follows:
i= Detergent for the pre-wash
(1/3of the total amount
recommended).
j= Detergent for the main wash
including Soak, if selected
§= Fabric conditioner or liquid
starch
^Close the detergent drawer.
See "Detergent" for further information.
WASHING
19

GSelect Delay start
If required please refer to "Delay start"
for more information.
HStart the programme
^Press the flashing Start/Stop button.
The estimated programme duration will
start counting down in one minute
steps. During the first few minutes the
machine measures how much water is
being absorbed by the laundry. The
programme duration may be longer or
shorter depending on this absorbency
rate.
The programme sequence is also
shown in the display. The washer-dryer
shows you when each section of the
programme is reached.
The drum lighting switches off once the
programme has started.
IRemove the laundry when the
programme has finished
The anti-crease phase starts as soon as
the programme finishes.
The machine will switch off
automatically 15 minutes after the
end of the anti-crease phase. You will
need to press the Kbutton to switch
it back on again.
^Turn the programme selector to the
Stop position.
^Open the drum door and remove the
laundry.
Check that all items have been
removed from the drum. Items left in
the drum could discolour other items
in the next wash or become
discoloured themselves.
Important: Always remove the
laundry before switching the machine
off. This is important to ensure that
the load size indicator works
correctly.
^Switch the machine off using the
Kbutton.
See "After each washing or drying
programme" in "WASHING AND
DRYING" for further information.
After washing a full load
If you have washed a full load of
laundry and you wish to dry the
laundry in the washer-dryer
afterwards you will have to remove
half the load. Carry out the drying
procedure in two batches.
20
WASHING