mikroElektronika ccRF click User manual

1. Introduction
Once you have soldered the headers your
board is ready to be placed into desired
mikroBUS™socket. Make sure to align the
cut in the lower-right part of the board
with the markings on the silkscreen at
the mikroBUS™socket. If all of the pins are
aligned correctly, push the board all
the way into the socket.
3. Plugging the board in
2 3
2. Soldering the headers
1
4. Essential features
Turn the board upward again. Make sure
to align the headers so that they are
perpendicular to the board, then solder the
pins carefully.
Turn the board upside down so that
bottom side is facing you upwards.
Place shorter pins of the header into the
appropriate soldering pads.
Before using your click™board, make sure
to solder 1x8 male headers to both left
and right side of the board. Two 1x8 male
headers are included with the board in
the package.
click
BOARD
www.mikroe.com
ccRF click Manual
ver. 1.01
0 100000 023952
ccRF click™is an accessory board in
mikroBUS™form factor. It’s a compact and
easy solution for adding RF transceiver to
your design. It features CC2500 Low-Power
2.4 GHz RF transceiver as well as PCB
trace antenna. ccRF click™communicates
with the target board microcontroller via
mikroBUS™ SPI (MOSI, MISO, SCK, CS), RST
and PWM lines. The board is designed to
use 3.3V power supply only. LED diode
(GREEN) indicates the presence of power
supply.
ccRF click
ccRF click™with it’s CC2500 IC is a low-power
2.4 GHz transceiver designed for the 2400-
2483.5 MHz ISM and SRD frequency band.
The CC2500 is integrated with a highly
congurable baseband modem that supports
various modulation formats and has data rate
up to 500 kBaud. All these features make
this board ideal for consumer electronics,
wireless audio, wireless keyboard and mouse
RF remote controls and many more.
Downloaded from Arrow.com.

8. Support
MikroElektronika oers Free Tech Support
(www.mikroe.com/esupport) until the end
of product lifetime, so if something goes
wrong, we are ready and willing to help!
7. Code Examples
.com
Once you have done all the necessary
preparations, it’s time to get your click™
board up and running. We have provided
the examples for mikroC™, mikroBasic™and
mikroPascal™compilers on our Libstock
website. Just download them and you are
ready to start.
VCC3.3
R2
2K2
LD1
AN
RST
CS
SCK
MOSI
MISO
+3.3V
GND
PWM
INT
RX
TX
SCL
SDA
+5V
GND
VCC3.3
A1
IFA_2.4GHz
RF-SO
RF-SCLK
RF-SI
RF-CS#
RF-GDO0
C15
22pF
C16
22pF
R4 1M
X1
26MHz
C1 100pF
C3 100pF
C6
1pF
L3
1.2nH
L2 1.2nH
C2 1pF
L1 1.2nH
C4
1.8pF
C5
1.5pF
VCC-RF R1 56K
RF-SI
RF-CS# RF-GDO0
RF-OSC1 RF-OSC2
C7
100nF
R3 10K
17 18
19 20
2
3
4
5
6 7
10
9 8
1
11
12
13
14
15
16
CC2500
DVDD
GDO2
SO
SCLK
GDO0 CSn XOSC1 AVDD
RF_P
RF_N
AVDD
AVDD
RBIAS
DGRD
GND
SI
GND
DCPL
XOSC2
AVDD
GND
U1
RF-SO
RF-SCLK
RF-GDO2
RF-GDO2
C11
220pF
C9
100nF
C10
100nF
VCC3.3
FP1
C12
220pF
C13
100nF
VCC-RF
C8
10uF
C14
100nF
ANT
MikroElektronika assumes no responsibility or liability for any errors or inaccuracies that may appear in the present document.
Specication and information contained in the present schematic are subject to change at any time without notice. Copyright © 2013 MikroElektronika. All rights reserved.
6. PCB Trace Antenna
5. ccRF click™Board Schematic
Board features PCB trace antenna, designed
for the 2400-2483.5 MHz frequency band.
Maximum device range is up to 20 meters in
open space.
Downloaded from Arrow.com.Downloaded from Arrow.com.