mikroElektronika ccRF2 click User manual

2 3
ver. 1.00
ccRF2 click
™
manual
0 100000 027554
click™
BOARD
www.mikroe.com
2. Soldering the headers
1. Introduction
3. Plugging the board in
Once you have soldered the headers your
board is ready to be placed into the desired
mikroBUS™socket. Make sure to align the
cut in the lower-right part of the board with
the markings on the silkscreen at the
mikroBUS™socket. If all the pins
are aligned correctly, push the
board all the way into the socket.
Turn the board upward again. Make sure
to align the headers so that they are
perpendicular to the board, then solder
the pins carefully.
Turn the board upside down so that
the bottom side is facing you upwards.
Place shorter pins of the header into the
appropriate soldering pads.
Before using your click™board, make sure
to solder 1x8 male headers to both left
and right side of the board. Two 1x8 male
headers are included with the board in
the package.
4. Essential features
The CC1120 IC on ccRF2 click™provides
extensive hardware support for packet
handling, data buering, burst transmissions,
clear channel assessment, link quality
indication, and Wake-On-Radio. CC1120 also
integrates all lters, which removes the need
for costly external SAW and IF lters. It’s a
great solution for wireless communications
in home and building automation as well as
industrial monitoring and control.
1
ccRF2 click™
ccRF2 click™will enable you to add a high
performance, low power consumption
single-chip radio transceiver to your design.
It carries CC1120, the fully integrated
radio transceiver designed mainly the
ISM (Industrial, Scientic, and Medical)
and SRD (Short Range Device) frequency
bands at 164–192 MHz, 274–320 MHz,
410–480 MHz, and 820–960 MHz. ccRF2
click™communicates with the target board
through mikroBUS™ SPI (MISO, MOSI, CSK),
and AN, RST, CS, PWM and INT lines. The
board uses a 3.3V power supply only.
Downloaded from Arrow.com.

MikroElektronika assumes no responsibility or liability for any errors or inaccuracies that may appear in the present document.
Specification and information contained in the present schematic are subject to change at any time without notice. Copyright © 2014 MikroElektronika. All rights reserved.
5. ccRF2 click™board schematic
8. Support
7. Code examples
MikroElektronika oers free tech support
(www.mikroe.com/support) until the end
of the product’s lifetime, so if something
goes wrong, we’re ready and willing to help!
Once you have done all the necessary
preparations, it’s time to get your click™board
up and running. We have provided examples
for mikroC™, mikroBasic™and mikroPascal™
compilers on our Libstock website. Just
download them and you are ready to start.
C8
1.8nf
C10 47nf
C11 10nf
C3
47nf
C5
47nf
C4
47nf
C2
C1
47nf
C7
15pf
C6
15pf
C9 47nf
C12
47nf
C13
220nf
C17
47nf
C18
47nf
C14
33pf
C15
100nf
C16
100pf
R1
0R
R3
10R
L1 0.01uH
C19
47nf
R2
56K
31
4
2
Y1
FA-20H
GND P$1
GND P$2
SIGNAL
P$3
J3
U.FL
VCC VCC
VCC
VCC VCC VCC
VCC
VCC
VCC
VCC
RF-SCK
RF-RESET
RF-GPIO2
RF-CS
RF-GPIO0
RF-GPIO3
RF-SIMO
RF-SOMI
R4
0R
VCC-3V3
Text
RF-SCK
RF-CS
RF-GPIO0
RF-SIMO
RF-SOMI
RF-RESET
RF-GPIO2
RF-GPIO3
AVDD_IF
13
AVDD_PFD_CHP 25
AVDD_RF
15
AVDD_SYNTH1 22
AVDD_SYNTH2 27
AVDD_XOSC 28
CS_N
11
DCPL
6
DCPL_PFD_CHP 26
DCPL_VCO 21
DCPL_XOSC 29
DO
9
DVDD
12
DVDD_2
5
EPAD
33
EXT_XOSC 32
GPIO0
10
GPIO2
4
GPIO3
3
LNA_N 20
LNA_P 19
LPF0 23
NC
16
PA 17
PLF1 24
RBIAS
14
RESET_N
2
SCLK
8
SI
7TRX_SW 18
VDD_GUARD
1
XOSC_Q1 30
XOSC_Q2 31
CC1120
U1
AN
RST
CS
SCK
MOSI
MISO
+3.3V
GND
PWM
INT
RX
TX
SCL
SDA
+5V
GND
MIKROBUS DEVICE CONN.
GND
GND
GND
GND GND
GND
GND
GND
GND GND
GND
GND
GND
GND GND
VCC- 3V3
P7
P5
P6
P9
P10
P8
P1
P2
P4
P3
IPC1
PWR
R5
2K2
GND
VCC- 3V3
ANT
GND1GND2
GND3
GND4
GND_NC
LNA_N
LNA_P
PA
TRX
.com
6. External antenna
connector
To use ccRF2 click™
you’ll need to connect
an external antenna
to the N.FL Series
Coaxial Connector.
To get one, search for
“antenna” at www.mikroe.com/store
Downloaded from Arrow.com.Downloaded from Arrow.com.