Milwaukee M18 48-59-1807 User manual

Cat. No. / No de cat.

48-59-1807

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

WARNING To reduce the risk of injury, user must read and understand operator's manual.

AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien

comprendre le manuel.

ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.

New batteries must be charged before rst use.

Les batteries neuves doivent être chargées avant leur

utilisation initiale.

Las baterías nuevas se deben cargar antes de usarlas

por primera vez.

M18™ AND M12™ RAPID CHARGE STATION

M18™ AND M12™ LITHIUM-ION BATTERY PACKS

STATION DE CHARGE RAPIDE DE BATTERIES M18™ET M12™

BLOCS DE BATTERIES LITHIUM-ION M18™ET M12™

ESTACIÓN DE CARGA RÁPIDA M18™ Y M12™

BATERÍAS DE IONES DE LITIO M18™ Y M12™

1. SAVE THESE INSTRUCTIONS - THIS MANUAL

CONTAINS IMPORTANT SAFETY AND OPER-

ATING INSTRUCTIONS FOR THE MILWAUKEE

LITHIUM-ION CHARGER CAT. NO. 48-59-1807 AND

MILWAUKEE M12™AND M18™LI-ION BATTERIES.

2. BEFORE USING THE BATTERY PACK AND CHAR-

GER, READ THIS OPERATOR’S MANUAL, YOUR

TOOL OPERATOR’S MANUAL, AND ALL LABELS

ON THE BATTERY PACK, CHARGER AND TOOL.

CAUTION

TO REDUCE THE RISK OF INJURY,

CHARGE MILWAUKEE M12™ AND

M18™ RECHARGEABLE LITHIUM-ION BATTERIES

ONLY IN MILWAUKEE M12™AND M18™LITHIUM-

ION CHARGERS. Other types of batteries may burst

causing personal injury and damage. Do not wire a battery

pack to a power supply plug or car cigarette lighter. Bat-

teries will be permanently disabled or damaged.

4. USE MILWAUKEE LITHIUM-ION PACKS ONLY ON

COMPATIBLE MILWAUKEE LITHIUM-ION TOOLS.

Battery pack and charger are not compatible with V™-

technology or NiCd systems. Use with other tools may

result in a risk of re, electric shock or personal injury.

5. AVOID DANGEROUS ENVIRONMENTS. Do not

charge battery pack in rain, snow, damp or wet

locations. Do not use battery pack or charger in the

presence of explosive atmospheres (gaseous fumes,

dust or ammable materials) because sparks may be

generated when inserting or removing battery pack,

possibly causing re.

6. CHARGE IN A WELL VENTILATED AREA. Do not

block charger vents. Keep them clear to allow proper

ventilation. Do not allow smoking or open ames near

a charging battery pack. Vented gases may explode.

7. MAINTAIN CHARGER CORD. When unplugging

charger, pull plug rather than cord to reduce the risk

of damage to the electrical plug and cord. Never

carry charger by its cord. Keep cord from heat, oil

and sharp edges. Make sure cord will not be stepped

on, tripped over or subjected to damage or stress.

Do not use charger with damaged cord or plug.

Have a damaged charger replaced immediately.

8. DO NOT USE AN EXTENSION CORD UNLESS IT

IS ABSOLUTELY NECESSARY. Using the wrong,

damaged or improperly wired extension cord could

result in the risk of re and electrical shock. If an

extension cord must be used, plug the charger

into a properly wired 16 gauge or larger extension

cord with pins that are the same number, size and

shape as the pins on the charger. Make sure that

the extension cord is in good electrical condition.

9. CHARGER IS RATED FOR 120 VOLT AC ONLY. Char-

ger must be plugged into an appropriate receptacle.

10. USE ONLY RECOMMENDED ATTACHMENTS. Use

of an attachment not recommended or sold by the

battery charger or battery pack manufacturer may

result in a risk of re, electric shock or personal injury.

11. UNPLUG CHARGER when not in use. Remove bat-

tery packs from unplugged chargers.

12. TO REDUCE THE RISK OF ELECTRIC SHOCK, al-

ways unplug charger before cleaning or maintenance.

Do not allow water to ow into AC/DC plug. Use a

Ground Fault Circuit Interrupter (GFCI) to reduce

shock hazards.

13. DO NOT BURN OR INCINERATE BATTERY

PACKS. Battery packs may explode, causing per-

sonal injury or damage. Toxic fumes and materials

are created when battery packs are burned.

14. DO NOT CRUSH, DROP, OR DAMAGE battery pack.

Do not use a battery pack or charger that has received

a sharp blow, been dropped, run over, or damaged in

any way (e.g., pierced with a nail, hit with a hammer,

stepped on).

15. DO NOT DISASSEMBLE. Incorrect reassembly may

result in the risk of electric shock, re or exposure

to battery chemicals. If it is damaged, take it to a

MILWAUKEE service facility.

16. BATTERY CHEMICALS CAUSE SERIOUS BURNS.

Never allow contact with skin, eyes, or mouth. If

a damaged battery pack leaks battery chemicals,

use rubber or neoprene gloves to dispose of it. If

skin is exposed to battery uids, wash with soap

and water and rinse with vinegar. If eyes are ex-

posed to battery chemicals, immediately ush with

water for 20 minutes and seek medical attention.

Remove and dispose of contaminated clothing.

17. DO NOT SHORT CIRCUIT. A battery pack will short

circuit if a metal object makes a connection between

the positive and negative contacts on the battery

pack. Do not place a battery pack near anything that

may cause a short circuit, such as coins, keys or

nails in your pocket. Do not allow uids to ow into

battery pack. Corrosive or conductive uids, such as

seawater, certain industrial chemicals, and bleach or

bleach containing products, etc., can cause a short

circuit. A short circuited battery pack may cause re,

personal injury, and product damage.

18. STORE YOUR BATTERY PACK AND CHARGER in

a cool, dry place. Do not store battery pack where tem-

peratures may exceed 120°F (50°C) such as in direct

sunlight, a vehicle or metal building during the summer.

19.ALWAYS USE A SIDE HANDLE when using a 9.0 Ah

or higher capacity battery pack; the output torque of

some tools may increase. If your drill/driver did not

come with a side handle, visit www. milwaukeetool.

com for the appropriate accessory handle.

SYMBOLOGY

Volts

Direct Current

Alternating Current

Double Insulated

Properly Recycle Batteries

WARNING

READ AND UNDERSTAND

ALL INSTRUCTIONS. Failure

to follow all instructions listed below, may result in

electric shock, re and/or serious personal injury.

SAVE THESE

INSTRUCTIONS

IMPORTANT

SAFETY

INSTRUCTIONS

Hertz

Amps

BFP Backfeed Protected

California Energy Commission

CUS

UL Listing for Canada and U.S.

FUNCTIONAL

DESCRIPTION

1. Light indicators:

Continuous red: Charging

Slow ashing green: Approaching full charge

Continuous green: Charging is complete

Fast ashing red: Battery is too hot/cold - Charging

will begin when battery reaches

correct charging temperature

Slow ashing red: Battery charge is pending -

Charging will begin when the rst

pack is fully charged

Flashing red/green: Damaged or faulty battery pack

2. Bays (12V on front,

18V on back)

3. Vents

4. Cord with

pass-through plug

5. Wall mount guides

6. Battery Contacts

7. Release Buttons

8. Fuel Gauge button

9. Fuel Gauge

10. Rapid charge-

capable pack indicator

SPECIFICATIONS

Charger Cat. No. ................................ 48-59-1807

Input Volts....................................................120 AC

Max Input Amps............................................6.0 AC

DC Output Volts...................................................12

Max DC Output Amps......................................4.5

DC Output Volts...................................................18

Max DC Output Amps......................................6.0

Recommended Ambient

Charging Temperature................... 40°F to 105°F

M18™ Li-Ion Battery Packs........................18 V DC

M12™ Li-Ion Battery Packs........................12 V DC

MILWAUKEE LI-ION

BATTERY PACKS

Fuel Gauge

Use the Fuel Gauge to determine

Less than 10% if bottom light

is ashing

Approximate Run Time Remaining

78-100 %

55-77 %

33-54 %

10-32 %

the battery pack's remaining run

time. Press the Fuel Gauge but-

ton to display the lights. The

Fuel Gauge will light up for 2-3

seconds. When less than 10%

of charge is left, 1 light on the

fuel gauge will ash slowly.

NOTE: If the Fuel Gauge doesn't appear to be working,

place the battery pack on the charger and charge as needed.

Compared to NiCd battery pack types, MILWAUKEE Li-Ion

battery packs deliver fade-free power for their entire run

time. The tool will not experience a slow, gradual loss of

power as you work. To signal the end of discharge, 1 light

on the fuel gauge will ash quickly for 2-3 seconds and the

tool will not run. Charge the battery pack.

NOTE: Immediately after using the battery pack, the Fuel

Gauge may display a lower charge than it will if checked

a few minutes later. The battery cells "recover" some of

their charge after resting.

Battery Pack Protection

To protect itself from damage and extend its life, the bat-

tery pack’s intelligent circuit monitors current draw and

temperature. In extremely high torque, binding, stalling,

and short circuit situations, the battery pack will turn OFF

the tool if the current draw becomes too high. All the fuel

gauge lights will ash. Release the trigger and restart.

Under extreme circumstances, the internal temperature of

the battery could become too high. If this happens, the fuel

gauge lights will ash in an alternating pattern and the tool

will not run. Allow the battery to cool down.

Fuel Gauge Lights Diagnosis Solution

Lights 1 - 4 Solid Remaining run time Continue working

1 Light, ashing

slowly Less than 10% run

time left Prepare to charge pack

1 Light, ashing

quickly End of discharge Charge pack

Lights 1-4, ashing

quickly Current draw too

high Release trigger and

restart, reduce pressure

Lights 1&3 / 2&4,

ashing alternatingly Battery temperature

too high Release trigger and allow

battery to cool

Cold Weather Operation

MILWAUKEE Li-Ion battery packs are designed to operate

in temperatures below freezing. When the battery pack is

too cold, it may need to warm up before normal use. Put

the battery on a tool and use the tool in a light application.

It may “buzz” for a short time until it warms up. When the

buzzing stops, use the tool normally.

RAPID CHARGE

STATION

WARNING

Charge only MILWAUKEE M18™

and M12™ Lithium-Ion batteries in

this MILWAUKEE Lithium-Ion charger. Other

types of batteries may cause personal injury and

damage.

When to Charge the Battery Pack

with this MILWAUKEE Charger

Remove the battery pack from the tool for charging

when convenient for you and your job. MILWAUKEE

batteries do not develop a "memory" when charged

after only a partial discharge. It is not necessary to run

down the battery pack before placing it on the charger.

•Use the Fuel Gauge to determine when to charge your

MILWAUKEE Li-Ion battery pack.

• You can "Top-Off" your battery pack's charge before

starting a big job or long day of use.

• The only time it is necessary to charge the MILWAUKEE

Li-Ion battery pack is when the battery pack has reached

the end of its charge. To signal the end of charge, power

to the tool will drop quickly, allowing you just enough

power to nish making a cut, drilling a hole, or driving

a fastener. Charge the battery pack as needed.

How to Charge the Battery Pack

Align the battery pack with the bay and slide the battery

pack into the charger as far as possible. The red light will

come on, either ashing quickly (battery pack is too hot or

cold), ashing slowly (battery pack is waiting for another

pack to nish charging) or continuous (pack is charging).

•The 48-59-1807 charges up to three battery packs at

a time, one in each of the three M12/M18 sets. The

rst pack loaded in each charger set will charge rst.

The second pack inserted in the charger set will begin

charging when the rst pack inserted is fully charged.

SET 1 SET 2 SET 3

• A fully discharged battery pack with an internal tempera-

ture in the normal range will charge in 30 to 90 minutes,

depending on the battery pack.

•Heavily cycled batteries may take longer to charge

completely.

•The Fuel Gauge lights on M18 battery packs are dis-

played as the pack is being charged, indicating how fully

charged the pack is. The fuel gauge will turn off when

charging is complete.

• After charging is complete, the continuous green light

will come on.

•The charger will keep the battery pack fully charged if it

is left on the charger. The light indicator will ash green

during this maintenance charging.

WARNING

To reduce the risk of re, personal

injury, and product damage due to

a short circuit, never immerse your tool, battery

pack or charger in uid or allow a uid to ow

inside them. Corrosive or conductive uids, such

as seawater, certain industrial chemicals, and

bleach or bleach containing products, etc., can

cause a short circuit.

Maintenance and Storage

Do not expose your battery pack or cordless tools to

water or rain, or allow them to get wet. This could damage

the tool and battery pack. Do not use oil or solvents to

clean or lubricate your battery pack. The plastic casing

will become brittle and crack, causing a risk of injury.

Store battery packs at room temperature away from

moisture. Do not store in damp locations where corrosion

of terminals may occur. As with other battery pack types,

permanent capacity loss can result if the pack is stored for

long periods of time at high temperatures (over 120° F).

MILWAUKEE Li-Ion battery packs maintain their charge

during storage longer than other battery pack types. After

about a year of storage, charge the pack as normal.

Transport

Personal transport of Li-Ion battery packs is allowed

when done in accordance with these warnings and in-

structions. The proper classication, packaging, labeling,

marking, and documentation requirements for shipping

Li-Ion batteries is dependent upon whether the particular

batteries are rated greater than or less than 100 Wh.

Generally, Li-Ion batteries rated 100 Wh or less are “ex-

cepted” from certain Class 9 DG requirements. Always

check compliance of Li-Ion battery consignments against

the current regulations governing the chosen mode of

transport. When in doubt, contact the carrier or other

trained Dangerous Goods professional to conrm ac-

ceptability. Li-Ion packs are shipped under classication

UN 3480 (battery only) or UN 3481 (batteries contained

in or packed with equipment).

WARNING

To reduce the risk of injury or ex-

plosion, never burn or incinerate a

battery pack even if it is damaged, dead or com-

pletely discharged. When burned, toxic fumes

and materials are created.

Disposing of MILWAUKEE Li-Ion

Battery Packs

MILWAUKEE Li-Ion battery packs are more environ-

mentally friendly than some other types of power tool

battery packs (e.g., nickel-cadmium). Always dispose of

your battery pack according to federal, state and local

regulations. Contact a recycling agency in your area for

recycling locations.

Even discharged battery packs contain some energy. Be-

fore disposing, use electrical tape to cover the terminals

to prevent the battery pack from shorting, which could

cause a re or explosion.

RBRC Battery Recycling Seals

The RBRC™ Battery Recycling Seals (see "Symbology")

on your tool battery packs indicate that MILWAUKEE has

arranged for the recycling of that battery pack with the

Rechargeable Battery Recycling Corporation (RBRC).

At the end of your battery pack's useful life, return the

battery pack to a MILWAUKEE Branch Ofce/Service

Center or the participating retailer nearest you. For more

information, visit the RBRC web site at www.rbrc.org.

• If the light indicator ashes red and green, check that

the battery pack is fully seated into the bay. Remove the

battery pack and reinsert. If the light continues to ash

red and green, remove pack(s) and unplug charger for

at least 2 minutes. After 2 minutes, plug charger back

in and insert pack. If the problem persists, contact a

MILWAUKEE service facility.

• If the light indicator does not come on, check that the

battery pack is fully seated into the bay. Remove the

battery pack and reinsert. If the light indicator still does

not come on, remove pack(s) and unplug charger for at

least 2 minutes. After 2 minutes, plug charger back in

and insert pack. If after these attempts the light indicator

still does not come on, contact a MILWAUKEE service

facility.

Charging a Hot or Cold Battery Pack

The Red Flashing Indicator light on the charger indicates

that the battery pack temperature is outside the charging

range. Once the battery pack is within the acceptable

range, normal charging will take place and the red light

will be continuous. Hot or cold batteries may take longer

to charge.

Li-Ion Charging Status

Battery Pack

Temperature Red Charger

Indicator Light Charging Status

Too Hot

Normal Range

Too Cold

Fast Flashing

Continuous

Fast Flashing

Not charging

Normal charging

Not charging

Powering the Charger with an Inverter

or Generator

The charger will operate with most generators and invert-

ers rated at 600 Watts or higher.

Maintenance and Storage

Store your charger in a cool, dry place.

As a general practice, it is best to unplug battery chargers

and remove batteries when not in use. No battery pack

damage will occur, however, if the charger and battery

pack are left plugged in.

Repairs

The charger has no serviceable parts.

Mounting to the Wall

Use the wall mount guides to mark the hanging points.

WARNING

To reduce the risk of injury, always

unplug the charger and remove the

battery from the charger before performing any

maintenance. Never disassemble the battery or

charger. Contact a MILWAUKEE service facility

for ALL repairs.

To reduce the risk of injury and damage, never

immerse your battery or charger in liquid or allow

a liquid to ow inside them.

Cleaning

Clean out dust and debris from charger vents and electri-

cal contacts by blowing with compressed air. Use only

mild soap and a damp cloth to clean the battery pack

and charger, keeping away from all electrical contacts.

Certain cleaning agents and solvents are harmful to

plastics and other insulated parts. Some of these in-

clude gasoline, turpentine, lacquer thinner, paint thinner,

chlorinated cleaning solvents, ammonia and household

detergents containing ammonia. Never use ammable or

combustible solvents around batteries, charger, or tools.

SERVICE - UNITED STATES

1-800-SAWDUST (1.800.729.3878)

Monday-Friday, 7:00 AM - 6:30 PM CST

or visit www.milwaukeetool.com

Contact Corporate After Sales Service Technical

Support with technical, service/repair, or warranty

questions.

Email: [email protected]

Become a Heavy Duty Club Member at

www.milwaukeetool.com to receive important

notications regarding your tool purchases.

SERVICE - CANADA

Milwaukee Tool (Canada) Ltd

1.800.268.4015

Monday-Friday, 7:00 AM - 4:30 PM CST

or visit www.milwaukeetool.ca

LIMITED WARRANTY

USA & CANADA

Every MILWAUKEE Battery Pack (sold with cordless product and/or as a replacement

battery pack) is warranted to the original purchaser only to be free from defects in material

and workmanship. Subject to certain exceptions, MILWAUKEE will repair or replace a

battery pack which, after examination, is determined by MILWAUKEE to be defective in

material or workmanship for the stated warranty period from date of purchase. Return

of the battery pack to a MILWAUKEE factory Service Center location or MILWAUKEE

Authorized Service Station, freight prepaid and insured, is required. For the proper shipping

procedure of battery packs, contact 1.800.SAWDUST (1.800.729.3878), or go to www.

milwaukeetool.com. A copy of the proof of purchase should be included with the return

product. This warranty does not apply to damage that MILWAUKEE determines to be

fromrepairs made orattemptedby anyoneother thanMILWAUKEE authorized personnel,

misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.

Battery Pack

Cat. No. Chemistry

Warranty Period

(from date of purchase)

48-11-1812, 48-11-1828 (Serial number prefix

"B41E" and later), 48-11-1840, 48-11-1850,

48-11-1860, 48-11-1865, 48-11-1890,

48-11-2402, 48-11-2440, 48-11-2460,

48-11-2830 (Serial number prefix "C71")

Lithium-Ion (Li-Ion) Three (3) Years

48-11-0490, 48-11-1815, 48-11-1820,

48-11-2001, 48-11-2401, 48-11-2420, 48-11-2430 Lithium-Ion (Li-Ion) Two (2) Years

48-11-1828 (Serial number prefix "B41D" and

earlier), 48-11-1830 (Serial number prefix “A95”),

48-11-2830 (Serial number prefix "A71")

Lithium-Ion (Li-Ion)

Two (2) Years –

plus, Three (3) Years

Pro-Rata (prorated)*

48-11-0100, 48-11-1024, 48-11-1830 (Serial

number prefix “E95”), 48-11-1970, 48-11-2230

Nickel-Cadmium (Ni-Cd),

Nickel-Metal-Hydride (Ni-MH),

Lithium-Ion (Li-Ion)

One (1) Year

*The warranty period for MILWAUKEE M18™ 48-11-1828 (with the serial number

prefix "B41D" and earlier), V18™48-11-1830 (with the serial number prefix “A95”),

and V28™ 48-11-2830 (with the serial number prefix "A71") is five (5) years / 2000

charges from the date of purchase, whichever first occurs. The first 1000 charges or

2 years of the warranty, whichever first occurs, are covered through free replacement

of the defective battery. This means that for the earlier of the first 1000 charges or two

(2) years from the date of purchase/first charge, a replacement battery will be provided

to the customer for any defective battery free of charge. Thereafter, the remaining

charges up to a total of 2000 or the remainder of the five (5) year period from the date

of purchase, whichever first occurs, will be covered on a pro rata basis. This means that

every customer gets an additional 1000 charges or three (3) years of pro rata warranty

on the these battery packs, depending upon the amount of use. MILWAUKEE M18™

48-11-1828 (with the serial number prefix "B41E" and later), V18™48-11-1830 (with the

serial number prefix “E95”), and M28™ 48-11-2830 (with the serial number prefix "C71")

have different warranty periods, as listed.

WarrantyRegistration isnotnecessary to obtainthe applicablewarrantyon a MILWAUKEE

battery pack. The manufacturing date of the product will be used to determine the warranty

period if no proof of purchase is provided at the time warranty service is requested.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES

DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE

OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS CONDITION,

YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE

BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE

DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR

DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE

OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS

FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS

EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR

ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED

WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE; TO

THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED

WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS

WARRANTY AS DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS

ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY

NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND

YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

This warranty applies to product sold in the U.S.A. and Canada only.

Please consult the ‘Service Center Search’ in the Parts & Service section of MILWAUKEE’s

websitewww.milwaukeetool.com or call 1.800.SAWDUST (1.800.729.3878) to locate your

nearestservicefacilityforwarrantyandnon-warrantyserviceonaMILWAUKEEBatteryPack.

LIMITED WARRANTY

USA & CANADA

Every MILWAUKEE power tool* (see exceptions below) is warranted to the original

purchaser only to be free from defects in material and workmanship. Subject to certain

exceptions, MILWAUKEE will repair or replace any part on an electric power tool

which, after examination, is determined by MILWAUKEE to be defective in material or

workmanship for a period of ve (5) years** after the date of purchase unless otherwise

noted. Return of the power tool to a MILWAUKEE factory Service Center location or

MILWAUKEE Authorized Service Station, freight prepaid and insured, is required. A

copy of the proof of purchase should be included with the return product. This warranty

does not apply to damage that MILWAUKEE determines to be from repairs made or

attempted by anyone other than MILWAUKEE authorized personnel, misuse, alterations,

abuse, normal wear and tear, lack of maintenance, or accidents.

Normal Wear: Many power tools need periodic parts replacement and service to

achieve best performance. This warranty does not cover repair when normal use has

exhausted the life of a part including, but not limited to, chucks, brushes, cords, saw

shoes, blade clamps, o-rings, seals, bumpers, driver blades, pistons, strikers, lifters,

and bumper cover washers.

*This warranty does not cover Air Nailers & Staplers; Airless Paint Sprayer; Cordless

Battery Packs; Gasoline Driven Portable Power Generators; Hand Tools; Hoist – Electric,

Lever & Hand Chain; M12™ Heated Gear; Reconditioned Product; and Test & Measure-

ment Products. There are separate and distinct warranties available for these products.

**The warranty period for Job Site Radios, M12™ Power Port, M18™ Power Source,

Jobsite Fan and Trade Titan™ Industrial Work Carts is one (1) year from the date of

purchase. The warranty period for the Drain Cleaning Cables is two (2) years from

the date of purchase. The warranty period for the M18™ Compact Heat Gun and the

8 Gallon Dust Extractor is three (3) years from the date of purchase. The warranty period

for the LED in the LED Work Light and the LED Upgrade Bulb for the Work Light is the

lifetime of the product subject to the limitations above. If during normal use the LED or

LED Bulb fails, the part will be replaced free of charge.

Warranty Registration is not necessary to obtain the applicable warranty on a

MILWAUKEE power tool product. The manufacturing date of the product will be used

to determine the warranty period if no proof of purchase is provided at the time war-

ranty service is requested.