1918
HD 28 SG
ENGLISH
TECHNICAL DATA DIE GRINDER
Noise information
Wear ear protectors!
Vibration information
W
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Safety Warnings Common for Grinding
This power tool is intended to function as a grinder.
Read all safety warnings, instructions, illustrations and
specifi cations provided with this power tool.
b) Operations such as wire brushing, cut-off, sanding
and polishing are not recommended to be performed
with this power tool.
c) Do not use accessories which are not specifi cally
designed and recommended by the tool manufacturer.
d) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power tool.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool.
f) The arbour size of wheels, sanding drum or any other
accessory must properly fi t the spindle or collet of the
power tool.
g) Mandrel mounted wheels, sanding drums, cutters or
other accessories must be fully inserted into the collet
or chuck. The “overhang” or the length of the mandrel
from the wheel to the collet must be minimal.
h) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires. If
power tool or accessory is dropped, inspect for damage
or install an undamaged accessory. After inspecting
and installing an accessory, position yourself and
bystanders away from the plane of the rotating
accessory and run the power tool at maximum noload
speed for one minute.
i) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and shop apron capable of stopping
small abrasive or workpiece fragments.
j) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment.
k) Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
WARNING
may contact hidden wiring.
l) Always hold the tool fi rmly in your hands during the
start-up.
m) Use clamps to support workpiece whenever
practical. Never hold a small workpiece in one hand and
the tool in the other hand while in use.
n) Never lay the power tool down until the accessory
has come to a complete stop.
o) After changing the bits or making any adjustments,
make sure the collet nut, chuck or any other adjustment
devices are securely tightened.
p) Do not run the power tool while carrying it at your
side.
q) Regularly clean the power tool’s air vents.
r) Do not operate the power tool near fl ammable
materials.
s) Do not use accessories that require liquid coolants.
Kickback and related warnings
Maintain a fi rm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction
during start-up.
b) Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
c) Do not attach a saw chain woodcarving blade or
toothed saw blade.
d) Always feed the bit into the material in the same
direction as the cutting edge is exiting from the material
(which is the same direction as the chips are thrown).
e) When using steel saws, cut-off wheels, high-speed
cutters or tungsten carbide cutters, always have the
work securely clamped.
Safety Warnings Specifi c for Grinding
Use only wheel types that are recommended for your
power tool and only for recommended applications. For
example: do not grind with the side of a cut-off wheel.
b) For threaded abrasive cones and plugs use only
undamaged wheel mandrels with an unrelieved
shoulder fl ange that are of correct size and length.
c) Do not position your hand in line with and behind the
rotating wheel.
d) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
e) Use extra caution when making a “pocket cut” into
existing walls or other blind areas.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
ENGLISH
