Mindray BeneVision TD60 User manual

Quick Reference Guide
BeneVision TD60
Display Telepack

Note: The TD60 Quick Reference Guide is not intended
as a replacement to the Operating Instructions. Prior
to operating equipment, the user must be familiar
with the Operating Instructions Manual contents. This
document is a guideline only to be used as an aid to
comprehensive Inservice Training.

TD60 Physical View .................................................1
General Navigation .................................................3
Swipe for More Data....................................................3
View More Data ........................................................4
Quick Key/Screen Menu Bar Deployment................................5
Patient Setup .......................................................6
Admit ..................................................................6
Discharge ..............................................................6
Adjust Patient Category ................................................6
Standby .............................................................7
Enter Standby ..........................................................7
Resume Monitoring ....................................................8
Printing .............................................................8
Nurse Call ...........................................................8
Activate a Nurse Call ...................................................8
Acknowledge the Nurse Call ............................................8
ECG ..................................................................9
Select ECG Leadwire ....................................................9
Lead Placement ........................................................9
Enable Pacer ..........................................................10
Resp ............................................................... 11
Set NCM Alarm Delay ..................................................11
SpO2(OPTIONAL) ................................................. 12
Connect the SpO2Module .............................................12
Initiate the SpO2Measurement ........................................13
NIBP (OPTIONAL) ................................................. 14
Table of Contents
P/N: H-046-007060-00 Rev 3.0

Pair a TD60 with a BP10................................................14
Pair a TD60 with a New BP10...........................................14
Unpair a TD60 with a BP10 via the TD60 ................................15
Unpair a TD60 with a BP10 via the BP10 ................................15
Technical Alarms .................................................. 15
Alarm Reset ...........................................................15
Screen Display .................................................... 16
Switch Orientation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Flip the Landscape Display.............................................16
Adjust Display Order...................................................17
Screen Lock/View Only Mode .................................... 17
Enable the Screen Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Unlock the Screen in Locked Mode.....................................18
Unlock the Screen in View Only Mode .................................18
Adjust Volumes ................................................... 18
Parameter Colors ................................................. 19
Clean/Disinfect the TD60 ......................................... 19
Clean the TD60 .......................................................19
Disinfect the TD60 .....................................................23
Clean/Disinfect Reusable Accessories ............................ 23
Sterilization ....................................................... 23
P/N: H-046-007060-00 Rev 3.0
Table of Contents (cont'd)

P/N: H-046-007060-00 Rev 3.0 1
BeneVision TD60 Quick Reference Guide
TD60 PHYSICAL VIEW
1. Display Activation (Power On/Off ) key
When the TD60 is powered off
• Pressing this key will turn the TD60 on.
When the TD60 is powered on
• And the screen display is on, pressing this key will turn the display off.
• And the screen display is off, pressing this key will turn the display on.
• Press and hold this key for two seconds to display the power off
confirmation menu.
2. Nurse Call key
Nurse call key activates nurse call message at the Central Monitoring
System (CMS).
3. Main Menu key
• Pressing this key when on the main screen will open the main menu.
• Pressing this key when a menu is open will return to the main screen.
• Pressing this key when the display is off will turn the display on.
• Pressing this key when the screen lock mode is configured for View Only
will display the Screen Locked menu.
5
4
3
1 2
6 8
7
9
10

P/N: H-046-007060-00 Rev 3.0 2
BeneVision TD60 Quick Reference Guide
4. Display
Touch screen display for viewing patient information and adjusting patient
settings.
5. Patient alarm light indicator
6. ECG lead connector
7. SpO2cap
Covers SpO2connector when SpO2is not in use.
8. SpO2connector
Connects the SpO2module.
9. Speaker
10. Battery compartment
Contains the lithium-ion battery pack or AA battery tray.

P/N: H-046-007060-00 Rev 3.0 3
BeneVision TD60 Quick Reference Guide
GENERAL NAVIGATION
Swipe for More Data
Swipe
Swipe
Swipe
Swipe

P/N: H-046-007060-00 Rev 3.0 4
BeneVision TD60 Quick Reference Guide
View More Data
The TD60 provides the following shortcuts to access additional information, as
shown in the following figure:
• Tap to enter the Patient Info menu
• Tap to to view the MPAN info
• Tap to enter the System Info menu to view Battery Information

P/N: H-046-007060-00 Rev 3.0 5
BeneVision TD60 Quick Reference Guide
Quick Key/Screen Menu Bar Deployment
Note: The quick keys are configurable. This image is just representative.
Swipe up
Press

P/N: H-046-007060-00 Rev 3.0 6
BeneVision TD60 Quick Reference Guide
PATIENT SETUP
Admit
When admitting a TD60 for the first time, the device must be admitted to the
system through the CMS.
After first admitting the device to the CMS, you can directly admit the next
patient on the TD60 by discharging the previous patient, and then pressing
to admit a new patient.
Discharge
Discharging the patient will stop monitoring, clear patient information, and
restore default (preset) settings on the TD60.
A patient can be discharged by selecting the Discharge Patient menu, and
then selecting that a new patient is on the TD60.
Note: Discharging the patient on the TD60 discharges the patient from the
CMS.
Select the Discharge Patient menu
1. Press to enter the main menu.
2. Tap Discharge Patient.
3. Select Yes.
• The patient is discharged from both the TD60 and the CMS.
• The patient's configuration is cleared and the configuration is restored
to the saved user configuration or factory default configuration.
• The patient will be added to the discharged patients list at the CMS.
4. Press to admit a new patient.
Adjust Patient Category
The Patient Info menu allows the clinician to adjust the patient category.
Note: Ensure the patient category selection is appropriate for the patient
before monitoring begins. The supported patient categories are Adult
and Pediatric.