Minelab GPX 6000 User manual

This is an abbreviated guide. Read the
full-length GPX 6000™ User Manual at
www.minelab.com/GPX6000manual
POCKET GUIDE
Quick Start
Factory Reset Procedure
Controls
Display
Bluetooth® Headphones
Pairing the ML 100 headphones
Intelligent Automatic Operation
Manual Sensitivity Adjustment Procedure
Noise Cancel Procedure
Double-D Coil Noise Cancel Procedure
Quick-Trak Ground Balance Procedure
Ground Balance Procedure
Contents

Quick Start
Beginning with Factory Default Settings is
recommended before using this Quick Start
procedure.
100 mm (4")
10 s
TURN ON
1
RAISE AND LOWER
COIL FOR 10 s
2
BEGIN DETECTING
3
Return to Contents

Factory Reset Procedure
Factory default settings can be restored at
any time by conducting a Factory Reset.
START 
1. Ensure the detector is powered off.
2. Press and hold the
power button for
7 seconds.
3. ‘FP’ (Factory Preset)
is displayed.
Return to Contents

Controls
1
7
2
3
4
6
5
8
1. Bluetooth® Control
Enables Bluetooth® for
connection of wireless
headphones.
Initiates Bluetooth® pairing
mode for connecting Bluetooth®
headphones (long-press for at
least 2.5 s).
2. Backlight Adjust
Cycles through the backlight
brightness settings — high,
medium, low and off.
3. Power On/Off
Turns the detector on and off.
Restores factory default settings
(press and hold from off for at
least 7 s).
4. Sensitivity Adjust
Adjusts the sensitivity level.
5. Ground Type
Toggles between Difficult and
Normal Ground Type.
Toggles between the Threshold
On/Off settings (long-press for
at least 2.5 s).
6. Noise Cancel
Initiates the Noise Cancel
process.
When a Double-D coil is
connected, toggles between the
Double-D Modes — EMI Cancel
and Conductive Ground Cancel
(long-press for at least 2.5 s).
7. Volume Adjust
Adjusts the audio Volume Level.
8. Quick-Trak
Press and hold Quick-Trak
Ground Balance to conduct a
Ground Balancing operation.
Return to Contents

Display
1
2
5
4
910
3
6
7
8
1. Bluetooth® Indicator
Indicates that Bluetooth® wireless audio is
on.
Bluetooth® Qualcomm® aptX™ Low
Latency
Standard Bluetooth
2. Double-D Mode Indicator
Only available when using a Double-D coil.
Electromagnetic Interference (EMI)
Cancel (default)
Conductive Ground Cancel
3. Backlight Indicator
Indicates that the backlight is on.
4. Ground Type
Displays the selected Ground Type.
Difficult
(default) Normal
5. Noise Cancel
Flashes when Noise Cancel is in progress.
6. Headphones Connection
Indicates that headphones are connected.
Bluetooth® headphones connected.
Wired headphones connected
7. Error
Indicates that there is a system error.
8. Volume Level
Displays the detector audio volume.
9. Sensitivity Level
Displays the sensitivity level.
Levels 1 to 10 are
manual settings.
Levels 11 and 12 are
automatic settings — Auto,
and Auto+.
10. Battery Level
Indicates the current battery level.
Return to Contents

Bluetooth® Headphones
1
2
3
4
5
6
1. Volume Plus button (+)
2. Multi-function button
3. Volume Minus button (−)
4. Status LED
Pairing mode (alternating blue and red)
Connected (flash every 3 sec)
On, not connected (flash every 2 sec)
Charging
Charging complete (Off)
5. USB Micro-B charging socket
6. Headphone socket 3.5 mm (⁄ inch)
Return to Contents

Pairing the ML 100 headphones
START 
1. Make sure headphones are off, and
close to the detector.
Ensure the headphones are turned off
and are no more than 1 metre (3.3 feet)
away from the detector.
2. Turn on the headphones
and enter pairing mode.
Press and hold the Multi-Function button
on the headphones until two ascending
tones are heard and the Status LED
alternates blue and red.
3. Enable Bluetooth® on
the detector and enter
pairing mode.
Press and hold the Bluetooth® button on
the side of the GPX 6000™ control panel
until the Bluetooth® indicator begins to
flash rapidly.
For first-time use of the detector or
following a factory reset, a short press
of the Bluetooth® button will immediately
initiate the pairing sequence.
4. Headphones will
automatically connect.
If pairing is successful, the headphones
beep, and the Bluetooth® and wireless
headphones indicators will remain on.
The Status LED on the headphones will
flash blue once every 3 seconds during
use.
To Factory Reset the ML 100 headphones,
press the Multi-Function button for more
than 10 seconds. All previous pairings and
settings will be deleted.
Return to Contents

Intelligent Automatic Operation
The procedure below is a fail-safe way
to begin detecting in a high-sensitivity
automatic mode. Once complete, the
GPX 6000™ will automatically maximise
sensitivity while minimising noise, so you
can concentrate on finding gold.
START 
1. Factory Reset the
detector.
Long-press for at
least 7 s
2. Hold the coil 100 mm
(4 in) above the ground. 100 mm (4")
3. Raise and lower coil for
10 seconds.
 Begin detecting.
Every 5 to 10 minutes throughout your
detecting session, it is recommended
that the coil is raised and lowered above
the ground a couple of times from
10 to 100 mm (⁄ to 4 in). This ensures
that the detector is thoroughly ground
balanced and operating at maximum
sensitivity. In environments with more
ground noise, repeat this process more
frequently.
 If the conditions are very quiet,
increase sensitivity from Auto to
Auto+.
 If the detector becomes noisy,
conduct a Noise Cancel Procedure.
 If this doesn’t resolve
the noise, follow the
Double-D Coil Noise Cancel Procedure.
Return to Contents

Manual Sensitivity Adjustment
Procedure
Always try the
Noise Cancel Procedure and the
Quick-Trak Ground Balance Procedure to
resolve noise before reducing the
sensitivity level.
Generally start with a Mono coil unless
you are detecting in areas with known
high levels of EMI or soil conductivity.
START 
1. Set sensitivity to
level 1.
2. Increase until false
signals occur.
3. Reduce by one level.
4. Check over ground and
reduce if needed.
Return to Contents

Noise Cancel Procedure
If audio responses become erratic due to
EMI, initiate the Noise Cancel process to
automatically select a quieter detecting
channel.
START 
1. Hold the coil 100 mm (4
in) above the ground. 100 mm (4")
2. Press the
Noise Cancel button.
3. Wait for confirmation
tone (approximately
5 seconds).
 Begin detecting.
 If the detector is still noisy when
using a mono coil, follow the
Double-D Coil Noise Cancel Procedure.
Return to Contents