MINOURA W-3100 User manual

Repairstand "W-3100" instructions manual
Tool Tray (option)
Back Knob
Clutch Release Lever
Upper Pillar
Lower Frame
Right Side Leg
Adjusting Screw
Clamp Adjust Knob
Clamp Lever
Clamp Jaws
Gear Clutch
Upper Pillar Holding Bolt
Lock Bolt
PARTS NAME
Left Side Leg
HOW TO ASSEMBLE W-3100 Required Tools: 1 x 13mm Spanner
1 x 6mm Hex Wrench
1 x 5mm Hex Wrench
Assemble both Legs to the Lower Frame with the supplied
M8x40 bolts and M8 Nylon Nuts.
M8x40 Cap Bolt
M8 Nylon nut
1

2
Place the assembled Lower Frame on the oor,
and check if every Adjusting Screw is touching the
oor perfectly.
If not, adjust the length of the Adjusting Screw then
tighten the lock nut rmly by a 13mm spanner.
This is very important to keep enough stability
while your bike is on the stand.
13mm spanner
3
Assemble the clamp jaw unit to the Upper Pillar.
The Back Knob should be tightened as rmly as
possible until the clamp jaws rotates smoothly.
4
Insert the assembled Upper Pillar into the Lower
Frame until the bottom cut-outs catch the Upper Pillar
Holding Bolt, then tighten the Lock Bolt rmly by a
5mm hex wrench.
To install the optional Tool Tray, insert the tray into
the Upper Pillar BEFORE assembling the frames.
Fix the position, then tighten the knob bolt.
Lock Bolt

HOW TO CLAMP YOUR BIKE
Pull down the Clamp Lever
to open the jaws.
12Place the top frame or the seat pillar
onto the lower jaw, then fully pull up the
Clamp Lever to close the jaws.
3Turn the Clamp Adjust Knob clockwise to
securely hold the bike.
Turning counter-clockwise will widen the
opening.
4To rotate the clamp jaws, push down the
Clutch Release Lever then rotate the jaws.
Release your nger after conrming the
ratch is securely engaged to the gear.
ABOUT OUR WARRANTY PROGRAM
You are covered under our warranty program for maximum 5 years from the date of your purchase.
Any defects caused by the manufacturer's mistake will be solved with this program at manufacturer's
expense, but any problem caused by the user's misuse or natural worn will not be supported by this
program.
Minoura does not owe any responsibility to any extra troubles these problems may bring.
For more detail, refer the attached "MINOURA LIMITED WARRANTY POLICY" card in the package.
(Maximum Load Capacity: 40 kgs / 90 lbs)
CONTACT INFORMATION
MINOURA NORTH AMERICA MINOURA JAPAN HEADQUARTERS
(for U.S. residents only) (for all other customers)
1996 East Ave. Hayward, CA 94541 U.S.A. 1197-1 Godo, Anpachi, Gifu 503-2305 Japan
Phone: [phone] Fax: [phone]
Fax: [phone] Email: [email protected]
Email: [email protected] Web: www.minoura.jp
MADE IN JAPAN

W-3100 / SMALL PARTS LIST
C-3
C-4
C-11
C-6 C-7
C-8
P-4 P-3
C-9
C-10
C-11
P-1
T-4 T-2
P-5
P-8
P-9
L-9
L-3 L-4
L-3
L-4
L-10
L-11
P-7
P-7
C-4
L-11
C-3: Clamp Rubber
C-4: Lock Clip
C-6: Clamp Shaft
C-7: Clutch Packing
C-8: Clamp Space Collar
C-9: M8 Flat Washer
C-10: Back Knob
C-11: Clamp Jaws Assy
P-1: Upper Pillar
P-3: Clutch Release Lever
P-4: Pivot Screw
P-5: Pillar Cap
P-7: Upper Pillar Holding Bolt & Nut
P-8: Lock Bolt
P-9: Lower Frame
L-3: Leg End Cap
L-4: Adjusting Screw
L-9: Left Side Leg
L-10: Right Side Leg
L-11: M8x40 Bolt & M8 Nylon Nut
T-2: Tray Fixing Knob Bolt
T-4: Tool Tray w/ tool slots