Mitsubishi Electric CITY MULTI PAC-PH01EHYU-E User manual

<ORIGINAL>
Air-Conditioners For Building Application
OUTDOOR UNIT
PANEL HEATER
PAC-PH01EHYU-E, PAC-PH02EHYU-E, PAC-PH03EHYU-E
GBF
MANUEL D’INSTALLATION
Veuillez lire le manuel d’installation en entier avant d’installer ce climatiseur pour éviter tout accident et vous assurer d’une utilisation correcte.
INSTALLATION MANUAL
For safe and correct use, please read this installation manual thoroughly before installing the air-conditioner unit.
E
MANUAL DE INSTALACIÓN
Para un uso seguro y correcto, lea detalladamente este manual de instalación antes de montar la unidad de aire acondicionado.
WT09190X01.book 1 ページ ２０１８年１１月２９日 木曜日 午前８時５９分

2
6. Installation Procedures
66.0
<A>
[Fig. 6.0.1]
<A> Remove the front panel from the unit by unscrewing the eight screws.
* Remove the snow protection hood (optional parts), if any.
S-module
BD
CA
<A>
<B>
<A>
<A> Remove the top attachment and the bottom attachment connecting
the main control box and inverter control box by unscrewing the two
screws.
<B> Remove the cover from main control box by unscrewing the three
screws.
ATop attachment
BBottom attachment
CMain control box
DInverter control box
[Fig. 6.0.2]
C
BB
A
AA
<A>
<A>
<A>
Right sideLeft side Rear side
[Fig. 6.0.3]
<A> Unscrew the three screws each on the right,
left and rear fin-guards.
<B> Remove the metal sheet wiring cover.
AFin-guard
BCover wiring 1
CCover wiring 4 (in case of left side)
WT09190X01.book 2 ページ ２０１８年１１月２９日 木曜日 午前８時５９分

3
66.0
<A>
A
<A>
B
[Fig. 6.0.4]
Left side Right side
<A> Unscrew the two screws each on the right and left
panels.
ALeft panel
BRight panel
A
<A>
[Fig. 6.0.5]
<A> Unscrew the two screws on the rear panel.
ARear panel
Rear side
WT09190X01.book 3 ページ ２０１８年１１月２９日 木曜日 午前８時５９分

4
66.1
<A>
L-module
[Fig. 6.1.1]
<A> Remove the front panel from the unit by unscrewing the 14 screws.
* Remove the snow protection hood (optional parts), if any.
[Fig. 6.1.2]
A
<A>
<A> Remove the control box front cover by unscrewing
the five screws.
AControl box front cover
C
BB
AA
<A> <A>
Right sideLeft side
<A> Unscrew the three screws each on the right
and left fin-guards.
<B> Remove the metal sheet wiring cover.
AFin-guard
BCover wiring 1
CCover wiring 4 (in case of left side)
[Fig. 6.1.3]
WT09190X01.book 4 ページ ２０１８年１１月２９日 木曜日 午前８時５９分

5
66.1
BB
A
<A> <A>
A
Rear side
[Fig. 6.1.4]
<A> Unscrew the three screws each on the rear
fin-guards.
<B>Remove the metal sheet wiring cover.
AFin-guard
BCover wiring 1
[Fig. 6.1.5]
<A> Unscrew the two screws each on the right
and left panels.
ALeft panel
BRight panel
<A>
A
Left side
B
<A>
Right side
<A>
A
[Fig. 6.1.6]
<A> Unscrew the four screws on the rear panels.
ARear panel
Rear side
WT09190X01.book 5 ページ ２０１８年１１月２９日 木曜日 午前８時５９分

6
66.2
<A>
XL-module
[Fig. 6.2.1]
<A> Remove the front panel from the unit by unscrewing the 14 screws.
* Remove the snow protection hood (optional parts), if any.
A
<A>
[Fig. 6.2.2]
<A> Remove the control box front cover by unscrewing
the five screws.
AControl box front cover
C
BB
AA
<A>
<A>
Left side Right side
[Fig. 6.2.3]
<A> Unscrew the three screws each on the right
and left fin-guards.
<B> Remove the metal sheet wiring cover.
AFin-guard
BCover wiring 1
CCover wiring 4 (in case of left side)
WT09190X01.book 6 ページ ２０１８年１１月２９日 木曜日 午前８時５９分

7
66.2
[Fig. 6.2.4]
BB
A
<A>
<A>
A
Rear side
<A> Unscrew the three screws each on the
rear fin-guards.
<B> Remove the metal sheet wiring cover.
AFin-guard
BCover wiring 1
<A>
AB
<A>
[Fig. 6.2.5]
Left side Right side
<A> Unscrew the two screws each on the
right and left panels.
ALeft panel
BRight panel
<A>
A
[Fig. 6.2.6]
<A> Unscrew the two screws on the rear panels.
ARear panel
Rear side
WT09190X01.book 7 ページ ２０１８年１１月２９日 木曜日 午前８時５９分

8
7. Panel Heater Installation
77.0
<A>
B
A
[Fig. 7.0.1]
<A> Attach the panel heater to the upper side of the left
panel and tighten it with two screws together.
ALeft panel
BPanel heater L
(Left wiring port type, wiring color: Yellow)
Left side <Wiring port>
<A>
B
A
[Fig. 7.0.2]
Right side
<A> Attach the panel heater to the upper side of the right panel
and tighten it with two screws together.
ARight panel
BPanel heater R
(Right wiring port type, wiring color: Blue)
<Wiring port>
<B>
<A> B
AC
S-module
<A> Attach the rubber spacer to the screw hole.
<B> Attach the panel heater to the upper side of the rear
panel and tighten it with two screws together.
(Attach the panel heater using the supplied long type
M5 screws.)
ARear panel
BRubber spacer
CPanel heater B
(Left wiring port type, wiring color: White)
[Fig. 7.0.3]
<Wiring port>
WT09190X01.book 8 ページ ２０１８年１１月２９日 木曜日 午前８時５９分

9
77.1
<A>
<B> <B>
B
A
C
D
A
<A> B
[Fig. 7.1.1]
<A> Attach the rubber spacer to the screw hole.
<B> Attach the panel heater to the upper side of the rear panel and tighten it with two
screws together. (Attach the panel heater using the supplied long type M5 screws.)
ARear panel
BRubber spacer
CPanel heater BR
(Left wiring port type, wiring color: White)
DPanel heater BL
(Right wiring port type, wiring color: Red)
Right rear side Left rear side
L/XL-module
<Wiring port>
<Wiring port>
WT09190X01.book 9 ページ ２０１８年１１月２９日 木曜日 午前８時５９分

10
8. Electrical Wiring
88.1.0
[Fig. 8.1.0.1] Left side
S-module
<A>Cut the tie band that fixes the cover of the unit wiring and remove the cover.
<B>Remove the water-proof cap from the unit wiring connector (the male end of the
connecter).
<C>Pull up the panel heater wirings so that the wirings run along the left rear pillar.
<D>Connect the panel heater wiring and the unit wiring and run the connected wiring
between the fin guard and the pillar.
<E>Place the cover back and fix the cover with the tie band.
AUnit wiring
BCover
CTie band
DWater-proof cap on the unit wiring connector
EPanel heater wiring
FFin guard
GPillar
<D>
<C>
AF
F
E
A
GGE
<E>
C
F
A
B
E
<A>
<A>
<B>
C
A
A
B
B
D
WT09190X01.book 10 ページ ２０１８年１１月２９日 木曜日 午前８時５９分