Mitsubishi Electric MUZ-GA25VA User manual

SERVICE MANUAL
CONTENTS
1. TECHNICAL CHANGES ····································4
2. PART NAMES AND FUNCTIONS······················8
3. SPECIFICATION·················································9
4. NOISE CRITERIA CURVES·····························11
5. OUTLINES AND DIMENSIONS ·······················12
6. WIRING DIAGRAM ··········································13
7. REFRIGERANT SYSTEM DIAGRAM··············19
8. PERFORMANCE CURVES······························21
9. ACTUATOR CONTROL····································29
10. SERVICE FUNCTIONS·····································30
11. TROUBLESHOOTING······································30
12. DISASSEMBLY INSTRUCTIONS·····················51
13. PARTS LIST······················································54
14. RoHS PARTS LIST···········································58
Wireless type
Models
SPLIT-TYPE, HEAT PUMPAIR CONDITIONERS
MUZ-GA25VA -
MUZ-GA25VA -
MUZ-GA25VA -
MUZ-GA25VA -
MUZ-GA35VA -
MUZ-GA35VA -
MUZ-GA25VAH -
MUZ-GA25VAH -
MUZ-GA25VAH -
MUZ-GA25VAH -
MUZ-GA35VAH -
MUZ-GA35VAH - E2
E1
E4
E3
E2
E1
E2
E1
E4
E3
E2
E1
NOTE:
RoHS compliant products have <G> mark on the spec name plate.
For servicing of RoHS compliant products, refer to the RoHS Parts List.
HFC
utilized
R410A
Please void OB379 REVISED EDITION-B.
No. OB379
REVISED EDITION-C
Revision:C
●MUZ-GA25VA(H)- has been added.
E4
OUTDOOR UNIT
Indoor unit service manual
MSZ-GA•VA Series (OB378)
MSZ-CB•VA Series (OB441)
OB379 C--1qxp 07.2.1 2:25 PM Page 1

2
Revision:A
•Alternative inverter P.C.board has been added(Refer to 11-7.1. Inverter P.C.board (Alternative)). FUSE F901 has been
equipped to MUZ-GA35.
•model has been added.
Quick clean kit has been removed.
E2
Model 6. Wiring diagram 11-6.N Check of inverter P.C.board
Change Change
MUZ-GA25VA
MUZ-GA25VAH
MUZ-GA35VA
MUZ-GA35VAH
No change No change
Revision:B
•MUZ-GA25VA(H)- has been added.
•11-2. Failure mode recall function has been changed.
•RoHS PARTS LIST has been added.
E3
Revision:C
•MUZ-GA25VA(H)- has been added.
•Solenoid valve coil has been removed.
(MUZ-GA25VA- :Serial No. 6021351T~ , MUZ-GA25VAH- :Serial No. 7000001T~)
E3E3
E4
OB379 C--1qxp 07.2.1 2:25 PM Page 2

3
1TECHNICAL CHANGES
MUZ-A09YV - ➔MUZ-GA25VA -
MUZ-A09YVH - ➔MUZ-GA25VAH - E1E1
E1E1
MUZ-A12YV - ➔MUZ-GA35VA -
MUZ-A12YVH - ➔MUZ-GA35VAH - E1E1
E1E1
1.Indication of capacity has been changed.(BTU base ➔kW base)
2.Control method between indoor and outdoor unit has been changed.
3.Power supply method has been changed (change to supply from outdoor unit).
4.Terminal block for power supply has been added.
5.Power P.C. board has been changed.
6.Inverter P.C. board has been changed.
7.Refrigerant circuit has been changed.
•Compressor has been changed.(KNB073FBVH➔KNB065FDTH)
•LEV has been removed and capillary tube has been added.
•Bypass circuit for low outside temperature operation has been added.
•Specification and position of muffler have been changed.
•Path of outdoor heat exchanger has been changed.
•4-way valve and R.V. coil have been changed.
•Stop valve has been changed.
8.Fan motor has been changed. (AC)
9.Shape of grille has been changed.
10.Shape of service panel has been changed.
11.Shape of propeller has been changed.
12.Quick Clean Kit has been added.
13.Symbol on terminal block has been changed (to S1/S2/S3).
1.Indication of capacity has been changed.(BTU base ➔kW base)
2.Control method between indoor and outdoor unit has been changed.
3.Power supply method has been changed (change to supply from outdoor unit).
4.Terminal block for power supply has been added.
5.Power P.C. board has been changed.
6.Inverter P.C. board has been changed.
7.Refrigerant circuit has been changed.
•Compressor has been changed.(KNB092FAAH➔KNB073FDVH)
•Specification and position of muffler have been changed.
•Path of outdoor heat exchanger has been changed.
•4-way valve and R.V. coil have been changed.
•Stop valve has been changed.
8.Fan motor has been changed.(AC➔DC)
9.Shape of grille has been changed.
10.Shape of service panel has been changed.
11.Shape of propeller has been changed.
12.Quick Clean Kit has been added.
13.Symbol on terminal block has been changed (to S1/S2/S3).
MUZ-GA25VA - ➔MUZ-GA25VA -
MUZ-GA25VAH - ➔MUZ-GA25VAH -
MUZ-GA35VA - ➔MUZ-GA35VA -
MUZ-GA35VAH - ➔MUZ-GA35VAH - E2E1
E2E1
E2E1
E2E1
1.Quick clean kit has been removed.
MUZ-GA25VA - ➔MUZ-GA25VA -
MUZ-GA25VAH - ➔MUZ-GA25VAH - E3E2
E3E2
1.Capillary tube for heating has been added.
2.Solenoid valve coil has been removed.(GA25VA- :Serial No. 6021351T~ , GA25VAH- :Serial No. 7000001T~)
E3E3
MUZ-GA25VA - ➔MUZ-GA25VA -
MUZ-GA25VAH - ➔MUZ-GA25VAH - E4E3
E4E3
1.Refrigerant circuit has been changed.
2.Solenoid valve coil has been removed.
OB379 C--1qxp 07.2.1 2:25 PM Page 3

4
Refrigeration
oil
Refrigerant
New refrigerant
R410A
HFC-32: HFC-125 (50%:50%)
Pseudo-azeotropic refrigerant
Not included
A1/A1
72.6
-51.4
1.557
64
Non combustible
0
1730
From liquid phase in cylinder
Possible
Incompatible oil
Non
Non
Previous refrigerant
R22
R22 (100%)
Single refrigerant
Included
A1
86.5
-40.8
0.94
44.4
Non combustible
0.055
1700
Gas phase
Possible
Compatible oil
Light yellow
Non
Refrigerant
Composition (Ratio)
Refrigerant handling
Chlorine
Safety group (ASHRAE)
Molecular weight
Boiling point (:)
Steam pressure [25:](Mpa)
Saturated steam density [25:](Kg/K)
Combustibility
ODP w1
GWP w2
Refrigerant charge method
Additional charge on leakage
Kind
Color
Smell
w1:Ozone Destruction Parameter : based on CFC-11
w2 :Global Warmth Parameter : based on CO2
INFORMATION FOR THE AIR CONDITIONER WITH R410A REFRIGERANT
•This room air conditioner adopts HFC refrigerant (R410A) which never destroys the ozone layer.
•Pay particular attention to the following points, though the basic installation procedure is same as that for R22 air
conditioners.
1As R410A has working pressure approximate 1.6 times as high as that of R22, some special tools and piping parts/
materials are required. Refer to the table below.
2Take sufficient care not to allow water and other contaminations to enter the R410A refrigerant during storage and
installation, since it is more susceptible to contaminations than R22.
3For refrigerant piping, use clean, pressure-proof parts/materials specifically designed for R410A. (Refer to 2. Refrigerant
piping.)
4Composition change may occur in R410A since it is a mixed refrigerant. When charging, charge liquid refrigerant to prevent
composition change.
NOTE : The unit of pressure has been changed to MPa on the international system of units(SI unit system).
The conversion factor is: 1(MPa [Gauge]) =10.2(kgf/ff[Gauge])
New Specification Current Specification
The incompatible refrigeration oil easily separates from
refrigerant and is in the upper layer inside the suction muffler.
Raising position of the oil back hole enables to back the
refrigeration oil of the upper layer to flow back to the
compressor.
Since refrigerant and refrigeration oil are compatible each,
refrigeration oil goes back to the compressor through the
lower position oil back hole.
Compressor
Suction muffler
Oil back hole
Refrigeration oil
Refrigerant
Compressor
Suction muffler
Oil back hole
Refrigeration oil /Refrigerant
Compressor
OB379 C--1qxp 07.2.1 2:25 PM Page 4

5
-30 -20 -10 0 10 20 30 40 50 60
-0.5
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
(MPa [Gauge])
R410A
R22
Conversion chart of refrigerant temperature and pressure
Saturated liquid pressure
(:)
NOTE : The unit of pressure has been changed to MPa on the
international system of units(SI unit system).
The conversion factor is: 1(MPa [Gauge]) =10.2(kgf/ff[Gauge])
R410A tools Can R22 tools be used?
Gas leak detector
R410A has high pressures beyond the measurement range of existing
gauges. Port diameters have been changed to prevent any other refrigerant
from being charged into the unit.
Hose material and cap size have been changed to improve the pressure
resistance.
Dedicated for HFC refrigerant.
6.35 mm and 9.52 mm
Description
Clamp bar hole has been enlarged to reinforce the spring strength in the tool.
Provided for flaring work (to be used with R22 flare tool).
Provided to prevent the back flow of oil. This adapter enables you to use
vacuum pumps.
It is difficult to measure R410Awith a charging cylinder because the
refrigerant bubbles due to high pressure and high-speed vaporization
No
No
No
Yes
Yes
New
New
New
Gauge manifold
Charge hose
Torque wrench
Flare tool
Flare gauge
Vacuum pump
adapter
Electronic scale for
refrigerant charging
No : Not Substitutable for R410A Yes : Substitutable for R410A
No 12.7 mm
1.Tools dedicated for the air conditioner with R410A refrigerant
The following tools are required for R410A refrigerant. Some R22 tools can be substituted for R410A tools.
The diameter of the service port on the stop valve in outdoor unit has been changed to prevent any other refrigerant being
charged into the unit. Cap size has been changed from 7/16 UNF with 20 threads to 1/2 UNF with 20 threads.
2.Refrigerant piping
1Specifications
Use the refrigerant pipes that meet the following specifications.
•Use a copper pipe or a copper-alloy seamless pipe with a thickness of 0.8 mm. Never use any pipe with a thickness less
than 0.8mm, as the pressure resistance is insufficient.
Wall
thickness
Outside diameter
Pipe mm
For liquid
For gas
6.35
9.52
12.7
0.8 mm
0.8 mm
0.8 mm
Heat resisting foam plastic
Specific gravity 0.045 Thickness 8 mm
Insulation material
OB379 C--1qxp 07.2.1 2:25 PM Page 5

6
Electronic scale for refrigerant charging
Outdoor unit
Refrigerant gas
cylinder
operating valve
Refrigerant gas cylinder
for R410A with siphon
Refrigerant (liquid)
Service port
Gauge manifold
valve (for R410A)
Union
Liquid pipe
Gas pipe
Stop valve
Indoor unit
Charge hose (for R410A)
R410A
Pipe diameter
mm
6.35
9.52
12.7
17
22
26
Dimension of flare nut
R22
17
22
24
2Flaring work and flare nut
Flaring work for R410A pipe differs from that for R22 pipe.
For details of flaring work, refer to Installation manual “FLARING WORK”.
3.Refrigerant oil
Apply the special refrigeration oil (accessories: packed with indoor unit) to the flare and the union seat surfaces.
4.Air purge
•Do not discharge the refrigerant into the atmosphere.
Take care not to discharge refrigerant into the atmosphere during installation, reinstallation, or repairs to the refrigerant
circuit.
•Use the vacuum pump for air purging for the purpose of environmental protection.
5.Additional charge
For additional charging, charge the refrigerant from liquid phase of the gas cylinder.
If the refrigerant is charged from the gas phase, composition change may occur in the refrigerant inside the cylinder and the
outdoor unit. In this case, ability of the refrigeration cycle decreases or normal operation can be impossible. However,
charging the liquid refrigerant all at once may cause the compressor to be locked. Thus, charge the refrigerant slowly.
OB379 C--1qxp 07.2.1 2:25 PM Page 6

7
ACCESSORIES
Air inlet
Air outlet
Drain outlet
Piping
Drain hose
(back and side)
1Drain socket 1
2Quick clean kit 1
MUZ-GA25VA - E1
MUZ-GA35VA - E1
–
1
MUZ-GA25VAH - E1
MUZ-GA35VAH - E1
1
MUZ-GA25VA - E2
MUZ-GA25VA - E3
–
MUZ-GA25VAH - E2
MUZ-GA25VAH - E3
MUZ-GA25VA - E4
MUZ-GA35VA - E2 MUZ-GA25VAH - E4 MUZ-GA35VAH - E2
––
MUZ-GA25VA MUZ-GA35VA
MUZ-GA25VAH MUZ-GA35VAH
PART NAMES AND FUNCTIONS
2
OB379 C--1qxp 07.2.1 2:25 PM Page 7

8
Single phase
230V,50Hz
1,890
10
3.6
0.24
KNB065FDTH
500
V-W 1.88
RA6V21-AB
WHT-BLK 347
BLK-RED 281
800o550o285
31
46
810
1
0.85
320 (NEO22)
Cooling
2.5 (0.9-3.0)
1.4
2.95
607
89
2.71
3.91
U-V 1.88
Heating
3.2 (0.9-4.5)
—
3.35
727
94
3.11
4.21
U-W 1.88
MUZ-GA25VA
MUZ-GA25VAH
Single phase
230V,50Hz
10
5.0
KNB073FDVH
550
V-W 1.53
RC0J50-AL
WHT-BLK 37.5
BLK-RED 37.5
RED-WHT 37.5
800o550o285
33
0.90
320 (NEO22)
Cooling
3.5 (1.0-3.9)
2.0
2,058
4.75
1,047
96
4.44
0.31
3.24
U-V 1.53
47
810/750
2
Heating
4.0 (0.9-5.0)
—
2,178
4.55
1,022
98
4.20
0.35
3.79
U-W 1.53
48
880/810/650
3
Outdoor model
Function
Power supply
Capacity Rated frequency(Min.-Max.)
Dehumidification
Air flow ✽1
Power outlet
Running current ✽1
Power input ✽1
Power factor ✽1
Starting current ✽1
Compressor motor current ✽1
Fan motor current ✽1
Model
Output
Winding
resistance(at 20:)
Model
Winding
resistance(at 20:)
Dimensions WOHOD
Weight
Sound level ✽1
Fan speed(High/Low, High/Med./Low)
Fan speed regulator
Refrigerant filling
capacity(R410A)
Refrigeration oil (Model)
kW
r/h
K/h
A
A
W
%
A
A
A
✽1
W
"
"
mm
kg
dB(A)
rpm
kg
cc
Compressor
Fan motor
Special remarks
Coefficient of performance(C.O.P)
Capacity
Electrical data
MUZ-GA35VA
MUZ-GA35VAH
NOTE : Test conditions are based on ISO 5151
Cooling : Indoor Dry-bulb temperature 27:Wet-bulb temperature 19:
Outdoor Dry-bulb temperature 35:Wet-bulb temperature(24:)
Heating : Indoor Dry-bulb temperature 20:Wet-bulb temperature 15:
Outdoor Dry-bulb temperature 7:Wet-bulb temperature 6:
Refrigerant piping length (one way): 5m
✽1 Measured under rated operating frequency
3SPECIFICATION
OB379 C--1qxp 07.2.1 2:25 PM Page 8

9
Model
Item
Current transformer
Current transformer
Smoothing capacitor
Diode module
Fuse
Fuse
Fuse
Defrost heater
Intelligent power module
Expansion valve coil
Reactor
Current-detecting resistor
Current-detecting resistor
Current-limiting resistor
Terminal block
Relay
Relay
Relay
Relay
R.V. coil
Solid state relay
Solenoid valve coil
Heater protector
Outdoor fan motor thermal fuse
MUZ-GA25VA
(CT)
(CT761, CT781)
(
C63A, C63B, C63C )
(DB61, DB65)
(F61)
(F71, F801)
( F901 w1)
(H)
(IPM)
(LEV)
(L61)
(R61)
(R831)
(
R64A, R64B )
(TB1,TB2)
(X63)
(X64)
(X66)
(X69)
(21S4)
(SR61)
(21R1)
(26H)
MUZ-GA25VAH MUZ-GA35VA MUZ-GA35VAH
ETA19Z59BZ
ETQ19Z71AY
620+ 420V
D25XB60
250V 20A
250V 3.15A
PS21244-A-203
10A 23.0mH
25m"5W
10"5W
3P
G5NB-1a
G4A-1A-PS
—
—
—
230V 130W
G5NB-1a
Open 45:
—
—
—
230V 130W
G5NB-1a
Open 45:
45m"5W (1 element)
250V 3.15A
CAM-MD12ME 12VDC
—
STF-01AJ503
—
—
—
—
—
G5NB-1a(for E1 /E2 /E3 )
SHF-4-10W5
G3MC-202PL
FQ-208-RK (for E1 /E2 /E3 w2)
Open 152:
Specifications and rating conditions of main electric parts
w1 Refer to Revision A.
w2 MUZ-GA25VA- (Serial No. ~6021350T)
MUZ-GA25VAH- (Serial No. ~7000000T)
E3
E3
OB379 C--1qxp 07.2.1 2:25 PM Page 9

10
NOISE CRITERIA CURVES
4
90
80
70
60
50
40
30
20
10 63 125 250 500 1000 2000 4000 8000
NC-60
NC-50
NC-40
NC-30
NC-20
NC-70
OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.0002 MICRO BAR
BAND CENTER FREQUENCIES, Hz
Test conditions
Cooling : Dry-bulb temperature 35: Wet-bulb temperature (24:)
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
COOLING
FUNCTION SPL(dB(A)) LINE
HEATING
46
46
Heating : Dry-bulb temperature 7: Wet-bulb temperature 6:
MUZ-GA25VA
MUZ-GA25VAH
90
80
70
60
50
40
30
20
10 63 125 250 500 1000 2000 4000 8000
NC-60
NC-50
NC-40
NC-30
NC-20
NC-70
OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.0002 MICRO BAR
BAND CENTER FREQUENCIES, Hz
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
COOLING
FUNCTION SPL(dB(A)) LINE
FAN SPEED
HEATING
47
48
Test conditions
Cooling : Dry-bulb temperature 35: Wet-bulb temperature (24:)
Heating : Dry-bulb temperature 7: Wet-bulb temperature 6:
OUTDOORUNIT
MICROPHONE
1m
High
Med.
MUZ-GA35VA
MUZ-GA35VAH
OB379 C--1qxp 07.2.1 2:25 PM Page 10