Mitsubishi Electric PUMY-P60NKMU User manual

Job Name:
Schedule Reference: Date:
Model: PUMY-P60NKMU (-BS)
Model Name
Unit Type PUMY-P60NKMU (-BS)
Nominal Cooling Capacity Btu/h 60,000
Nominal Heating Capacity Btu/h 66,000
Operating Temperature Range Cooling (Outdoor) *1 23° F ~ 115° F (-5 ° ~ +46° C) DB*
Heating (Outdoor) -4° F ~ +60° F (-20 ° ~ +15° C) WB
External Dimensions (H x W x D) In. / mm 52-11/16 x 41-5/16 x 13 (+1-3/16) / 1,338 x 1050 x 330 (+30)
Net Weight Lbs. / kg 313 / 142
Electrical Power Requirements Voltage, Phase, Hertz 208 / 230V, 1-phase, 60Hz
Cooling Power Input kW 4.80
Heating Power Input kW 6.15
Cooling Current A 21.5
Heating Current A 27.6
Minimum Circuit Ampacity (MCA) A 35
Recommended Fuse/Breaker Size A 40
Maximum Fuse Size A 42
Piping Diameter (Brazed) (In. / mm)Liquid (High Pressure) 3/8 / 9.52
Gas (Low Pressure) 3/4 / 19.05
Indoor Unit Total Capacity 50 to 130% of Outdoor Unit Capacity
Model / Quantity P06 to P72 / 1 to 12
Sound Pressure Levels dB(A) 58/59
Fan
Type x Quantity Propeller Fan x 2
CFM 4,940
Compressor Operating Range 22% to 100%
Compressor Type x Quantity INVERTER-driven Scroll Hermetic x 1
Compressor Motor Output kW 3.0
Refrigerant R410A
Lubricant FV50S
High-pressure Protection Device High Pressure Switch
Compressor / Fan Protection Device Compressor Thermo / Overcurrent Detection
Inverter Protection Device Overheat / Voltage Protection
AHRI Ratings
(Ducted / Non-Ducted)
EER 11.3 / 12.5
SEER 16.5 / 16.7
COP 3.70 / 3.14
BlueFin Anti-corrosion Protection: Cellulose- and polyurethane-resin coating treatment applied to condenser coil that protects it from air contaminants;
≥1μm thick; Salt Spray Test Method - no unusual rust development to 960 hours.
SEACOAST PROTECTION
•External Panel Base, External Front Panel, Pillar: Alloyed galvanized-steel sheets with thermoset polyester-resin coating on internal and external surfaces
•Compressor Cover: Galvanized-aluminum sheets with thermoset polyester-resin coating on internal and external surfaces
•Electrical Parts Box: Galvanized-aluminum sheets with thermoset polyester-resin coating on external surface
•Fan Motor Support: Galvanized-steel sheets with thermoset polyester-resin coating on internal and external surfaces
•Printed Circuit Board: Epoxy resin with polyurethane-coating on external surface
OUTDOOR VRF SYSTEM FEATURES
•
zoning technology
•Inverter-driven (variable speed) compressor
•Total refrigerant piping length of 492' (150 m)
•Uses CITY MULTI indoor units and Controls Network
UNIT OPTION
□Standard Model……………………….....PUMY-P60NKMU
□Sea Coast (BS) Model…………......PUMY-P60NKMU-BS
OPTIONAL PARTS
□Branch Joint (T-Branch)………………………………...CMY-Y62-G-E
□Header - Four-Branch…………………………………......CMY-Y64-G-E
□Header - Eight-Branch…………………………………..CMY-Y68-G-E
□Base Heater………………………………………........ PAC-SJ19BH-E
NOTES:
*1 If PKFY-P06/08 indoor units are connected, then range is 50° F ~ 115° F (10° C~ 46° C).
PUMY-P60NKMU (-BS)

Mitsubishi Electric Sales Canada Inc.
www.MitsubishiElectric.ca
Model: PUMY-P60NKMU (-BS) – DIMENSIONS
SB_PUMY-P60NKMU(-BS)_201211
7171
5OUTLINES AND DIMENSIONS
PUMY-P60NKMU
PUMY-P60NKMU-BS
Unit : mm <inch>
Refrigerant GAS pipe connection (FLARE) 19.05 3/4F)
Refrigerant LIQUID pipe connection (FLARE) 9.52 3/8F
Indication of STOP VALVE connection location.
1
2
Min.
Min.
Min. Min.
Service space
<Foundation bolt height>
Max.
The diagram below shows a basic example. Explantion of particular details are given in the installation manuals etc.
Dimensions of space needed for service access are shown in the below diagram.
Please secure the unit firmly with 4 foundation (M10<W3/8>) bolts. (Bolts and washers must be purchased locally.)
1 FREE SPACE (Around the unit)
2 SERVICE SPACE
3 FOUNDATION BOLTS
4 PIPING-WIRING DIRECTIONS
Piping and wiring connections can be made from 4 directions: FRONT, Right, Rear and Below.
30<1-3/16>
150
<5-29/32>
500
<19-11/16>
500
<19-11/16>
10<3/8>
Example of Notes
Piping Knockout Hole Details
FOUNDATION
Drain hole
5- 33<1-5/16>)
Bottom piping hole (Knockout)
154
<6-1/16>
136
<5-11/32>
45<1-25/32>
110<4-11/32>
160
<6-5/16>
160
<6-5/16>
160
<6-5/16>
81<3-3/16>
86<3-3/8>
Ground for the power supply ("GR"marking position)
Service panel
Handle for moving
2
1
Terminal connection Left For the power supply
Center For the transmission line
Right For concentration control
( )
Ground for the transmission line Ground for concentration control
Handle for moving
1 450<17-23/32>
1 393<15-15/32>
1079<42-15/32>
1050<41-11/32>
26<1-1/32>
369<14-17/32> 632<24-7/8>
1338<52-11/16>
362<14-1/4>
Scale 1:5
3/4 Conduit attachment
When installing the conduit. Set the attachment to the inner side of each panel.
27.8<1-3/32>
22.2<7/8>
1/2 Conduit attachment
100
<3-15/16>
24.7<31/32>
5<3/16>
22.5<7/8>
60<2-3/8>
Min. 1000mm<39-3/8> Min. 150mm<5-29/32>
Min. 10mm<3/8>Min. 10mm<3/8>
FREE
Rear piping hole (Knockout)
Rear trunking hole (Knockout)
Conduit hole (37<1-15/32>Knockout)
Conduit hole (24<15/16>Knockout)
60<2-3/8>
55<2-3/16>
55<2-3/16>27<1-1/16>
26<1-1/32>
5<3/16>
60<2-3/8>
73<2-7/8>
92<3-5/8>
75<2-15/16>
92
<3-5/8>
Right trunking hole (Knockout)
Conduit hole (37<1-15/32>Knockout)
Conduit hole (24<15/16>Knockout)
Right piping hole (Knockout)
73<2-7/8> 60<2-3/8>
5<3/16>
29<1-5/32>
27<1-1/16>
26<1-1/32>
92
<3-5/8>
53<2-3/32> 60<2-3/8>
55<2-3/16>
92<3-5/8>
92
<3-5/8>
Conduit hole (24<15/16>Knockout)
Front piping hole (Knockout)
Front trunking hole (Knockout)
Conduit hole (37<1-15/32>Knockout)
60<2-3/8> 55<2-3/16>
26<1-1/32>
5
<3/16>
60
<2-3/8>
73<2-7/8>
75<2-15/16>
92<3-5/8>
27<1-1/16> 55<2-3/16>
92
<3-5/8>
Air Discharge
Rear Air Intake
Side Air Intake
2-12×36 Oval holes (Foundation Bolt M10<W3/8>)
2-U Shaped notched holes (Foundation Bolt M10<W3/8>)
Installation Feet
25<31/32>
417<16-13/32>
42
<1-21/32>
61<2-13/32>
70
<2-3/4>
28<1-3/32> 19<3/4>370<14-9/16>
225
<8-27/32>
600<23-5/8>
225
<8-27/32>
330<13>
53<2-3/32> 56<2-7/32> 40<1-9/16>
0
Rear piping cover
Front piping cover
Air intake
Side Air IntakeRear Air Intake
Handle for moving
Handle for moving
OCH502