Mitsubishi Electric Q80BD-J71GP21-SX User manual

CC-Link IE Controller Network Interface Board
User's Manual (For SW1DNC-MNETG-B)
-Q80BD-J71GP21-SX
-Q80BD-J71GP21S-SX
-Q81BD-J71GP21-SX
-Q81BD-J71GP21S-SX

A- 1
SAFETY PRECAUTIONS
(Be sure to read these instructions before using the product.)
Before using this product, read this manual and the relevant manuals introduced in this manual carefully
and handle the product correctly with full attention to safety.
Note that these precautions apply only to this product. Refer to the user's manual of your CPU module for
safety precautions on programmable controller systems.
In this manual, the safety instructions are ranked as " WARNING" and " CAUTION".
Note that failure to observe the CAUTION level instructions may also lead to serious results depending on the
circumstances.
Be sure to observe the instructions of both levels to ensure personal safety.
Please store this manual in a safe place for future reference. This manual must be forwarded to the end user.
WARNING
CAUTION
Indicates that incorrect handling may cause hazardous conditions,
resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous conditions,
resulting in minor or moderate injury or property damage.

A- 2
[Design Precautions]
[Installation Precautions]
WARNING
Configure safety circuits external to the programmable controller to ensure that the entire system
operates safely even when a fault occurs in a personal computer. Failure to do so may result in an
accident due to an incorrect output or malfunction.
(1) Emergency stop circuits, protection circuits, and protective interlock circuits for conflicting
operations (such as forward/reverse rotations or upper/lower limit positioning) must be
configured external to the programmable controller.
(2) The station to which the board is installed may be disconnected from the data link due to a data
link error. If this occurs, the data output from the station and written to other stations before the
error will be held until the station is reconnected to the network (until its data link is restarted).
Provide a mechanism for data link status monitoring and error handling for each station that is
connected to the data link system.
For the operating status of each station after a communication failure, refer to CC-Link IE Controller
Network Reference Manual for each network. Incorrect output or malfunction due to a
communication failure may result in an accident.
When changing data during operation, configure an interlock circuit in the program to ensure that the
entire system will always operate safely. Configure an interlock circuit in the program, and determine
corrective actions to be taken between the external device and CPU module in case of a
communication failure.
Laser diodes are used in the optical transceivers of the CC-Link IE Controller Network. The laser
class (IEC 60825-1) of these laser diodes is Class 1. Do not look directly at laser light. Doing so may
harm your eyes.
CAUTION
Do not install the external power supply or communication cables together with the main circuit lines
or power cables. Keep a distance of 100mm (3.94 in.) or more between them. Failure to do so may
result in malfunction due to noise.
WARNING
Shut off the external power supply for the system in all phases before installing the board to or
removing it from the personal computer.
Failure to do so may result in electric shock or cause the board to fail or malfunction.
Do not touch any connectors while power is on. Doing so may cause electric shock or malfunction.

A- 3
CAUTION
Use the board in an environment that meets the general specifications in this manual.
Failure to do so may result in electric shock, fire, malfunction, or damage to or deterioration of the
product.
Do not directly touch any conductive parts and electronic components of the board.
Doing so may cause malfunction or failure of the board.
When installing the board, take care not to get injured by an implemented component or a
surrounding member.
Fix the board by tighten the board-fixing screws within the specified torque range.
Undertightening may cause drop of the component or wire, short circuit, or malfunction.
Overtightening may damage the screw and/or module, resulting in drop, short circuit, or malfunction.
For the tightening torque of the board-fixing screws, refer to the manual supplied with the personal
computer.
Before handling the board, touch a conducting object such as a grounded metal to discharge the static
electricity from the human body.
Failure to do so may cause the board to fail or malfunction.
Install the board to a personal computer which is compliant with PCI standard or PCI Express®
standard (Section 2.5 Operating Environment). Failure to do so may cause a failure or
malfunction.
Securely insert the board into the PCI slot following the board installation instruction of the personal
computer.
Incorrect insertion of the board may lead to a malfunction, failure or drop of the board.
When installing the board, take care not to get injured by an implemented component or a
surrounding member.
When installing the board, take care not to contact with other boards.
Handle the board in a place where static electricity will not be generated.
Failure to do so may cause a failure or malfunction.
The board is included in an antistatic envelope.
When storing or transporting it, be sure to put it in the antistatic envelope.
Failure to do so may cause a failure or malfunction.
Do not drop or apply a strong impact to the board.
Doing so may cause a failure or malfunction.

A- 4
[Wiring Precautions]
WARNING
Shut off the external power supply for the system in all phases before installing the board or starting
wiring.
Failure to do so may result in electric shock, damage to the product, or malfunction.
After installation of the board and wiring, attach the cover on the module before turning it on for
operation.
Failure to do so may result in electric shock.
CAUTION
Check the rated voltage and pin-out before wiring to the external power supply cable, and connect
the cables correctly.
Connecting a power supply with a different voltage rating or incorrect wiring may cause a fire or
failure.
Place the communication cable and the external power supply cable connected to the board in a
duct or clamp them.
If not, dangling cables may swing or inadvertently be pulled, resulting in damage to the board or
cables or malfunctions due to poor contact.
When disconnecting the cable from the board, do not pull the cable by the cable part.
Pulling the cable connected to the board may result in malfunction or damage to the board or cable.
Prevent foreign matter such as dust or wire chips from entering the personal computer.
Such foreign matter may cause a fire, failure, or malfunction.
Do not install the external power supply or communication cables together with the main circuit lines
or power cables.
Keep a distance of 100mm (3.94 in.) or more between them. Failure to do so may result in
malfunction due to noise.
Special skills and tools are required to connect the communication cable to the connector plug,
which is an exclusive product.
When purchasing it, please consult your local Mitsubishi representative.
Incomplete connection can result in a short, fire or malfunction.
Securely plug the communication cable to the connector of the board.
Then, check for any incomplete connection.
Poor contact may cause an erroneous input or output.

A- 5
[Wiring Precautions]
[Startup/Maintenance Precautions]
CAUTION
Use a specified tool for crimping of the cable and contacting pin. Imperfect crimping may cause a
malfunction.
Verify the pin-out and fully insert the crimped contacting pin into the connector. Imperfect insertion
may cause a failure or malfunction.
Insert the wired external power supply cable into the external power supply cable connector until a
click is heard.
Imperfect insertion may cause a failure or malfunction.
Always ground the personal computer to the protective ground conductor.
Failure to do so may cause a malfunction.
WARNING
Shut off all phases of the external power supply before cleaning the board or retightening the fixing
screws. Failure to do so may result in an electric shock, or cause a failure or malfunction of the
board.
Shut off the external power supply for the system in all phases before installing the board to or
removing it from the personal computer.
Failure to do so may result in electric shock or cause the board to fail or malfunction.
Do not connect or disconnect any communication cable while power is on.
Doing so may result in a malfunction.

A- 6
[Startup/Maintenance Precautions]
[Disposal Precautions]
CAUTION
Thoroughly read the manual and ensure the safety before performing program modification during
operation, forced output, operation such as RUN, STOP and PAUSE.
An improper operation will result in mechanical damage or accidents.
Do not disassemble or modify the board.
Doing so may cause failure, malfunction, injury, or a fire.
Fix the board by tighten the board-fixing screws within the specified torque range. Undertightening
may cause drop of the component or wire, short circuit, or malfunction. Overtightening may damage
the screw and/or module, resulting in drop, short circuit, or malfunction.
For the tightening torque of the board-fixing screws, refer to the manual supplied with the personal
computer.
Before handling the board, touch a conducting object such as a grounded metal to discharge the
static electricity from the human body.
Failure to do so may cause the board to fail or malfunction.
The board is included in an antistatic envelope.
When storing or transporting it, be sure to put it in the antistatic envelope.
Failure to do so may cause a failure or malfunction.
The microprocessor built in the board will reach a high temperature during operation. Do not touch it
directly when replacing the board.
Doing so may result in a failure, malfunction or injury.
CAUTION
When disposing of this product, treat it as industrial waste.

A- 7
CONDITIONS OF USE FOR THE PRODUCT
(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;
i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major
or serious accident; and
ii) where the backup and fail-safe function are systematically or automatically provided outside of
the PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.
(2) The PRODUCT has been designed and manufactured for the purpose of being used in general
industries.
MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT
LIMITED TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT,
WARRANTY, TORT, PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR
LOSS OR DAMAGE TO PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR
USED IN APPLICATION NOT INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS,
OR WARNING CONTAINED IN MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY
MANUALS, TECHNICAL BULLETINS AND GUIDELINES FOR the PRODUCT.
("Prohibited Application")
Prohibited Applications include, but not limited to, the use of the PRODUCT in;
• Nuclear Power Plants and any other power plants operated by Power companies, and/or any
other cases in which the public could be affected if any problem or fault occurs in the PRODUCT.
• Railway companies or Public service purposes, and/or any other cases in which establishment of
a special quality assurance system is required by the Purchaser or End User.
• Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as
Elevator and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation,
Equipment for Recreation and Amusement, and Safety devices, handling of Nuclear or
Hazardous Materials or Chemicals, Mining and Drilling, and/or other applications where there is a
significant risk of injury to the public or property.
Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the
PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT
is limited only for the specific applications agreed to by Mitsubishi and provided further that no
special quality assurance or fail-safe, redundant or other safety features which exceed the general
specifications of the PRODUCTs are required. For details, please contact the Mitsubishi
representative in your region.

A- 8
REVISIONS
*The manual number is given on the bottom left of the back cover.
Print Date *Manual Number Revision
APR., 2007 SH (NA)-080691ENG-A First edition
Oct., 2007 SH(NA)-080691ENG-B
Section 8.1.2, Appendix 3
GENERIC TERMS AND ABBREVIATIONS,
Section 1.2, Section 1.3, Section 2.5, Chapter 5, Section 8.1.1, Section 8.1.3,
Section 8.2, Section 8.3, Section 9.2.1, Section 9.2.3, Section 10.2.1,
Section 10.2.3, Chapter 15, Section 16.2, Section 16.3.1, Appendix 4
Section 8.1.2 changed to Section 8.1.3.
Jan., 2008 SH(NA)-080691ENG-C
"MELSECNET/G network system" (controller network) is changed to "CC-Link
IE Controller Network"
SAFETY PRECAUTIONS, PRECAUTIONS FOR USE, INTRODUCTION,
CONTENTS, MANUAL, HOW TO USE THIS MANUAL,
GENERIC TERMS AND ABBREVIATIONS, PACKING LIST, CHAPTER 1,
Section 1.1, Section 1.2, Section 1.3, Section 2.1, Section 2.2.2, Section 2.2.3,
Section 2.3, Section 2.3.2, Section 2.4, Section 2.5, Section 2.6, CHAPTER 3,
Section 3.1, Section 3.2, CHAPTER 4, Section 4.1, Section4.2, Section 4.2.1,
Section 5.1, CHAPTER 6, Section 6.1, Section 6.2, Section 6.2.1,
Section 6.2.2, Section 6.3, Section 6.4, Section 6.4.1, Section 6.5,
Section 6.5.1, Section 6.5.2, Section 6.5.3, Section 6.6, Section 6.6.1,
Section 6.6.2, CHAPTER 7, Section 7.1, Section 7.2, Section 7.3,
Section 7.3.3, Section 7.4, Section 7.5, Section 7.6, Section 7.7, Section 7.8,
Section 7.9, Section 8.1, Section 8.1.1, Section 8.1.2, Section 8.1.3,
Section 8.2, CHAPTER 9, Section 9.1, Section 9.1.1, Section 9.2,
Section 9.2.1, Section 9.2.2, Section 9.2.3, Section 9.2.4, Section 9.3,
Section 9.3.1, Section 9.3.2, Section9.3.3, Section 9.4, Section 9.4.1,
Section 9.4.6, Section 9.4.7, Section 9.4.8, Section 9.5.1, Section 9.5.3,
Section 9.5.4, Section 10.1.1, Section 10.2.1, Section 10.3, Section 10.4,
Section 10.5, CHAPTER 11, Section 11.1, Section 11.1.2, Section 11.2,
Section 12.1, Section 12.4, Section 12.5, Section 12.6, Section 12.7,
Section 12.8, Section 12.9, Section 13.1.1, Section 13.2, Section 13.2.1,
Section13.3, CHAPTER 14, Section 14.2, Section 14.2.1, Section14.2.2,
Section14.2.3, Section 14.3, CHAPTER 15, Section 16.2, Section 16.3,
Section 16.3.1, Section 16.4, Section 16.4.1, Section16.4.2, Section 16.4.3,
Section 16.4.4, Section 16.4.5, Section 16.4.6, Section 16.5.2, Section 16.5.3,
Section 16.5.4, Section 16.7, APPENDICES
Section 9.4.7
Addition
Correction
Correction
Addition