Mitsubishi Electric 800 Series User manual

PRE-OPERATION INSTRUCTIONS 1
INSTALLATION AND WIRING 2
PARAMETER 3
COMMON SPECIFICATIONS 4
INVERTER
Control terminal option
INSTRUCTION MANUAL
FR-E8TE7
Screw type terminal block

2
Safety Instructions
Thank you for choosing this Mitsubishi Electric inverter control terminal option.
This Instruction Manual provides handling information and precautions for use of the this product. Incorrect handling might cause an unexpected fault.
Before using this product, always read this Instruction Manual carefully to ensure proper use.
Please forward this Instruction Manual to the end user.
Electric shock prevention
WARNING
Do not remove the front cover or the wiring cover while the power of the inverter is ON, and do not run the inverter with the front cover or the
wiring cover removed as the exposed high voltage terminals or the charging part of the circuitry can be touched. Doing so may cause an
electric shock.
Even if power is OFF, do not remove the front cover of the inverter except for wiring or periodic inspection as the inside of this product is
charged. Doing so may cause an electric shock.
Before wiring or inspection, check that the display of the inverter operation panel is OFF. Any person who is involved in wiring or inspection
shall wait for 10 minutes or longer after the power supply has been cut off, and check that there are no residual voltage using a tester or the
like. The capacitor is charged with high voltage for some time after power OFF, and it is dangerous.
Any person who is involved in wiring or inspection of this product shall be fully competent to do the work.
The control terminal option must be installed before wiring. Otherwise you may get an electric shock or be injured.
Do not touch the control terminal option or handle the cables with wet hands. Doing so may cause an electric shock.
Do not subject the cables to scratches, excessive stress, heavy loads or pinching. Doing so may cause an electric shock.
WARNING Incorrect handling may cause hazardous conditions, resulting in death or severe injury.
Incorrect handling may cause hazardous conditions, resulting in medium or slight injury, or may cause only material
damage.
Do not attempt to install, operate, maintain or inspect this product until you have read this Instruction Manual and supplementary
documents carefully. Do not use this product until you have a full knowledge of this product mechanism, safety information and instructions.
In this Instruction Manual, the safety instruction levels are classified into "WARNING" and "CAUTION".
CAUTION
Note that even the level may lead to a serious consequence depending on conditions. Be sure to follow the instructions
of both levels as they are critical to personnel safety.
CAUTION

3
Injury prevention
Additional instructions
The following instructions must be also followed. If this product is handled incorrectly, it may cause unexpected fault, an injury, or an electric shock.
CAUTION
The voltage applied to each terminal must be as specified in the Instruction Manual. Otherwise an explosion or damage may occur.
The cables must be connected to the correct terminals. Otherwise an explosion or damage may occur.
The polarity (+ and -) must be correct. Otherwise an explosion or damage may occur.
While power is ON or for some time after power OFF, do not touch the inverter as it will be extremely hot. Doing so may cause burns.
CAUTION
Transportation and installation
Do not install or operate the control terminal option if it is damaged or has parts missing.
Do not stand or place any heavy object on the product.
Ensure the mounting orientation of this product is correct.
Foreign conductive objects must be prevented from entering the inverter. That includes screws and metal fragments or other flammable
substance such as oil.
If halogens (including fluorine, chlorine, bromine, and iodine) contained in fumigants for wood packages enter this product, the product may
be damaged. Prevent the entry of fumigant residuals or use an alternative method such as heat disinfection. Note that sterilization or
disinfection of wood packages should be performed before packing the product.
Test operation
Before starting the test operation, confirm or adjust the parameter settings. Failure to do so may cause some machines to make unexpected
motions.
WARNING
Usage
Do not modify this product.
Do not remove any part which is not instructed to be removed in the Instruction Manuals. Doing so may lead to a failure or damage of the
product.

4
CAUTION
Usage
As all parameters return to their initial values after Parameter clear or All parameter clear is performed, the parameters must be set again as
required before the operation is started.
To avoid damage due to static electricity, static electricity in your body must be discharged before you touch this product.
Maintenance, inspection and parts replacement
Do not carry out a megger (insulation resistance) test.
Disposal
This product must be treated as industrial waste.
General instruction
For clarity, illustrations in this Instruction Manual may be drawn with covers or safety guards removed. Ensure all covers and safety guards
are properly installed prior to starting operation.

5
— CONTENTS —
Safety Instructions 2
1 PRE-OPERATION INSTRUCTIONS 6
1.1 Unpacking and product confirmation............................................................................................................................6
1.1.1 Product confirmation ............................................................................................................................................................. 6
1.1.2 SERIAL number check.......................................................................................................................................................... 7
1.2 Component names ..........................................................................................................................................................8
1.3 Terminal layout ..............................................................................................................................................................10
1.4 Terminal connection diagram.......................................................................................................................................11
1.5 Details on the control circuit terminals .......................................................................................................................13
1.6 Communication specifications.....................................................................................................................................18
2 INSTALLATION AND WIRING 19
2.1 Pre-installation instructions .........................................................................................................................................19
2.2 Installation procedure ...................................................................................................................................................20
2.3 Wiring..............................................................................................................................................................................24
3 PARAMETER 27
3.1 Analog input selection ..................................................................................................................................................27
4 COMMON SPECIFICATIONS 29
Revisions 31

6PRE-OPERATION INSTRUCTIONS
1PRE-OPERATION INSTRUCTIONS
1.1 Unpacking and product confirmation
Take the control terminal option out of the package, check the product name, and confirm that the product is as you ordered
and intact.
This product is a control terminal option made for the FR-E800 series inverters.
This product cannot be connected to the Ethernet model and the safety communication model.
When this product is used, the inverter does not support functional safety functions as the safety stop input/output terminals
(S1, S2, SO, and SOC) on the inverter cannot be used.
Terminal 2 of this product is used for voltage input only.
1.1.1 Product confirmation
Check the enclosed items.
Control terminal option: 1

PRE-OPERATION INSTRUCTIONS 7
1
1.1.2 SERIAL number check
The FR-E8TE7 can be used with the inverters which have the following SERIAL number or later. Check the SERIAL number
indicated on the inverter rating plate or package.
NOTE
• The inverter firmware can be updated by using Firmware Update Tool of FR Configurator2. Even for an inverter which has a
SERIAL number earlier than the above, the FR-E8TE7 can be used by updating the inverter firmware to version 12 or later.
For details on firmware update, refer to the FR Configurator2 Instruction Manual.
Model Country of origin indication SERIAL number
Standard model MADE in Japan 237 or later
MADE in China 238 or later
The SERIAL consists of two symbols, three
characters indicating the production year and month,
and six characters indicating the control number.
The last two digits of the production year is indicated
as the Year, and the Month is indicated by 1 to 9, X
(October), Y (November), or Z (December).
□□ ○○ ○ ○○○○○○
Symbol Year Month Control number
SERIAL
SERIAL
number
Country
of origin
,1387;;;;;
02'(/)5(.
287387;;;;;
6(5,$/;;;;;;;;;;;
0$'(,1;;;;;
Rating plate example

8PRE-OPERATION INSTRUCTIONS
1.2 Component names
Symbol Name Description Refer to page
a Terminal block Used to connect the device to input signals to the inverter, and the device
to receive the signal from the inverter. 10
bBoard mounted option
connector Connected to the control circuit connection connector of the inverter. 19
c Control logic switch Control logic (sink logic, source logic) can be switched. The control logic of
input signals is initially set to the sink logic (SINK).
FR-E800
Instruction Manual
(Connection)
SOURCE
SINK
V
I
4
(a)
(a)
(e)
(d)
(c)
Front view Rear view
(b)
(f)

PRE-OPERATION INSTRUCTIONS 9
1
d Voltage/current input switch
For terminal 4 used for analog input, the voltage input (0 to 5 V, 0 to 10 V)
and current input (4 to 20 mA) (initial setting) are selectable. To change
the input specification, change the setting of Pr.267 and the voltage/
current input switch. (For details of Pr.267, refer to the FR-E800
Instruction Manual (Function).)
13
e Mounting hole Used to fix this product to the inverter by inserting a screw. 19
f PU connector Used for the RS-485 communication.
FR-E800
Instruction Manual
(Connection)
Symbol Name Description Refer to page

10 PRE-OPERATION INSTRUCTIONS
1.3 Terminal layout
SOURCESOURCE
SINKSINK
V
II
I
4
RUNRUN FUFU SESESTFSTF STRSTR SDSD
RHRH MRSMRS RESRES PCPC SDSD SDSD
1010 2 5
A B C
4
FMFM RLRL RMRM