Mitsubishi Electric PocketProjector PK10 User manual

EN-1
LED Projector "Pocket"
MODEL
PK10
User Manual
This User Manual is important to you.
Please read it before using your projector.

EN-2

EN-3
The lightning flash with arrowhead symbol within
an equilateral triangle is intended to alert the user to
the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS
AC ADAPTER’S PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET.
NOTE:
WHEN USING THE AC ADAPTER, THE SOCKET-OUTLET
SHALL BE INSTALLED NEAR THE EQUIPMENT AND
SHALL BE EASILY ACCESSIBLE.

EN-4
WARNING
Only use the attached specified AC adapter and power
cord. If you use another AC adapter and power cord, it
may cause interference with radio and television reception
or damage your projector.
The attached AC adapter and power cord are to be used
exclusively for this product. Never use them for other products.
DO NOT LOOK DIRECTLY INTO THE LENS WHEN
THE PROJECTOR IS IN THE POWER ON MODE.
CAUTION
Not for use in a computer room as defined in the Standard
for the Protection of Electronic Computer/Data Processing
Equipment, ANSI/NFPA 75.
When using the projector in Europe:
COMPLIANCE NOTICE
This Projector complies with the requirements of the EC
Directive 89/336/EEC “EMC Directive” as amended by
Directive 92/31/EEC and 93/68/EEC, and 73/23/EEC “Low
Voltage Directive” as amended by Directive 93/68/ EEC.
The electro-magnetic susceptibility has been chosen at a
level that gains proper operation in residential areas, on
business and light industrial premises and on small scale
enterprises, inside as well as outside of the buildings. All
places of operation are characterised by their connection
to the public low voltage power supply system.
Your MITSUBISHI ELECTRIC product
is designed and manufactured with high
quality materials and components which
can be recycled and reused.
This symbol means that electrical and
electronic equipment, at their end-of-
life, should be disposed of separately
from your household waste.
Please, dispose of this equipment at
your local community waste collection/
recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to converse the
environment we live in!
Note: This symbol
mark is for EU
countries only.
This symbol mark is
according to the
directive 2002/96/EC
Article 10 Information
for users and Annex
IV.

EN-5
Declaration of Conformity
Model Number : PK10
Trade Name : MITSUBISHI ELECTRIC
Responsible party : Mitsubishi Digital Electronics
America, Inc.
9351 Jeronimo Road, Irvine, CA
92618 U.S.A
Telephone number : [phone]
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Trademark, Registered trademark
Macintosh is registered trademark of Apple Computer Inc.
DLP., Digital Micromirror Device and DMD are all trademarks
of Texas Instruments.
Other brand or product names are trademarks or registered
trademarks of their respective holders.
Contents
Important safeguards......................................................6
Overview..........................................................................10
Power supply...................................................................11
Remote control (optional accessory).............................13
Installation.....................................................................15
Basic connections...........................................................16
Preparation.....................................................................18
Basic operation.............................................................20
Menu operation.............................................................23
Image adjustment............................................................26
Troubleshooting...............................................................28
Maintenance.....................................................................32
Indicators.........................................................................33
Specifications...................................................................35

EN-6
Important safeguards
Please read all these instructions regarding your projector
and retain them for future reference. Follow all warnings
and instructions marked on the projector.
1. Read instructions
All the safety and operating instructions should be
read before the appliance is operated.
2. Retain instructions
The safety and operating instructions should be
retained for future reference.
3. Warnings
All warnings on the appliance and in the operating
instructions should be adhered to.
4. Instructions
All operating instructions must be followed.
5. Cleaning
Unplug this projector both from the wall outlet and
battery before cleaning it. Do not use liquid aerosol
cleaners. Use a damp soft cloth for cleaning.
6. Attachments and equipment
Never add any attachments and/or equipment without
the approval of the manufacturer as such additions
may result in the risk of fire, electric shock or other
personal injury.
7. Water and moisture
Do not use this projector near water or in contact with
water. Never use the product if drop it in water.
8. Accessories
Do not place this projector on an unstable cart, stand,
tripod, bracket or table. Use only with a cart, stand,
tripod bracket, or table recommended by the
manufacturer or sold with the projector. Any mounting
of the appliance should follow the manufacturer’s
instructions and should use a mounting accessory
recommended by the manufacturer.
An appliance and cart combination should be moved
with care. Quick stops, excessive force and uneven
surfaces may cause the appliance and cart
combination to overturn.
9. Ventilation
Slots and openings in the cabinet are provided for
ventilation, ensuring reliable operation of the projector
and to protect it from overheating. Do not block these
openings or allow them to be blocked by placing the
projector on a bed, sofa, rug, or bookcase.
Ensure that there is adequate ventilation and that the
manufacturer’s instructions have been adhered to.
10. Power sources
This projector should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power, please consult your
appliance dealer or local power company.

EN-7
11. Power-cord protection
Power-supply cord should be routed so that it is not
likely to be walked on or pinched by items placed upon
or against it. Pay particular attention to cord at plug,
convenience receptacles, and points where it exit from
the appliance. Do not put the power cord under a
carpet.
12. Overloading
Do not overload wall outlets and extension cords as
this can result in a fire or electric shock.
13. Objects and liquids
Never push objects of any kind through openings of this
projector as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector, adaptor or
battery.
14. Servicing
Do not attempt to service this projector yourself. Refer
all servicing to qualified service personnel.
15. Damage requiring service
Unplug this projector from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
(a) If the power-supply cord or plug is damaged.
(b) If the adaptor or the battery is damaged.
(c) If liquid has been spilled, or objects have fallen
into the projector, adapter or battery.
(d) If the projector does not operate normally after
you follow the operating instructions. Adjust only
those controls that are covered by the operating
instructions. An improper adjustment of other
controls may result in damage and may often
require extensive work by a qualified technician
to restore the projector to its normal operation.
(e)If the projector has been exposed to rain or water.
(f )If the projector has been dropped or the cabinet
has been damaged.
(g) If the projector exhibits a distinct change in
performance- this indicates a need for service.
16. Replacement parts
When replacement parts are required, be sure that
the service technician has used replacement parts
specified by the manufacturer or parts having the
same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other
hazards.
17. Safety check
Upon completion of any service or repair to this
projector, ask the service technician to perform safety
checks determining that the projector is in a safe
operating condition.
18. Keep appropriate method when recharge the battery.
19. The projector is a precision instrument. Please pay
attention on static electricity.

EN-8
WARNING:
Unplug the power cord or remove the battery
immediately if there is something wrong with your
projector.
Do not operate if smoke, strange noise or odor comes out
of your projector, adaptor or battery. It may cause fire or
electric shock. In this case, unplug immediately and
contact your dealer.
Never remove the cabinet.
This product contains high voltage circuitry. An inadvertent
contact may result in an electric shock. Except as
specifically explained in User Manual, do not attempt to
service this product by yourself. Please contact your
dealer when you want to fix, adjust, or inspect the projector.
Do not modify the projector.
It can lead to fire or electric shock.
Do not keep using the damaged projector.
If the projector is dropped and the cabinet is damaged,
unplug the projector and contact your dealer for inspection.
It may lead to fire if you keep using the damaged projector.
Do not face the projection lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Only use the provided AC adaptor (02550-0112-00).
Do not place the projector on uneven surface.
Place the projector on a level and stable surface only.
Do not look into the lens when the projector is
operating.
It may hurt your eyes. Never let children look into the lens
when the projector is on.
Do not unplug the power cord or remove the battery
during operation.
It can lead to product failure, fire, electric shock or other
troubles.
Do not touch the air outlet grilles and bottom plate.
Do not touch them or put other equipment close to the air
outlet grilles because they become hot during operation.
The heated air outlet grilles and bottom plate may cause
injury or damage to other equipment. Also, do not put the
projector on a desk that is easily affected by heat.
Do not look into the air outlet grilles when projector is
operating.
Heat, dust, etc. may blow out of them and hurt your eyes.
Do not block the air inlet and outlet grilles.
If they are blocked, heat may be generated inside the projector,
causing deterioration in the projector quality and fire.
Don’t put upwards. Because of blocking exhausted hole.
Don’t drop.
Don’t throw it away.
Don’t project to person’s eyes.

EN-9
Place of installation
For safety’s sake, do not use the projector at any place
subjected to high temperature and high humidity.
Please maintain an operating temperature, humidity, and
altitude as specified below.
Operating temperature: between +41°F (+5°C) and
+95°F (+35°C)
Operating humidity: maximum 85%
Never put any heat-producing device under the
projector to prevent the projector from being
overheated.
Do not install the projector at a place that is unstable
or subject to vibration.
Do not install the projector near any equipment that
produces a strong magnetic field. Also refrain from
installing the projector near any cable carrying a large
amount of current.
Place the projector on a solid, vibration-free surface.
Otherwise it may fall, causing serious injury or damage.
Do not stand the projector on its end. It may fall,
causing serious injury or damage.
Do not place the projector near air-conditioning unit or
heater to avoid the air outlet and inlet grilles from being
exposed to hot air.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced Radio / TV
technician for help.
Changes or modifications not expressly approved by
Mitsubishi could void the user’s authority to operate this
equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class B digital apparatus complies with Canadian
ICES-003.

EN-10
Overview
1
2
5
8
4
9
7
63
COMPUTER
VIDEO
COMPUTER
VIDEO
AUTO POSITION
AUTO POSITION
1 Focus ring
2 Control panel
3 Terminal cover
4 Terminal board
5 Air outlet grille
6 Lens
7 Kensington lock
8 Remote control sensor (Rear side only)
9 Air inlet grille
Control panel
1 LAMP indicator
2 POWER indicator
3 CHARGE indicator
4 Four directional buttons
JS: AUTO POSITION
button
JX: VIDEO button
JW: COMPUTER button
5 ENTER button
6 POWER button
7 MENU button
Terminal board
1 S-VIDEO terminal
2 VIDEO terminal
3 VGA IN terminal
4 Power jack
1 2 3
4
1 2 3
4
67 5
AUTO POSITION
COMPUTER VIDEO
Bottom side
1 Battery latch
1