Mobatime ECO DC series User manual

MOBATIME BE-800697.09
INSTRUCTION MANUAL
Economy LED digital clock
ECO DC series

© MOBATIME 2 / 32 800697.09
Certification of the Producer
STANDARDS
Electrical safety: EN 62368-1 EMC: EN 55032, EN 55024, EN 50121 - 4
Applied EU Directives CE:
2006/95 / EC (LVD), 2004/108 / EC (EMC),
2011/65 / EC (RoHS), 2002/96 / EC (WEEE)
References to the instruction manual
1. The information in this instruction manual can be changed at any time without notice.
The current version is available for download on www.mobatime.com.
2. This instruction manual has been composed with the utmost care, in order to explain all details in
respect of the operation of the product. Should you, nevertheless, have questions or discover errors
in this manual, please contact us.
3. We do not answer for direct or indirect damages which could occur when using this manual.
4. Please read the instructions carefully and only start setting-up the product after you have correctly
understood all the information for the installation and operation.
5. The installation must only be carried out by skilled staff.
6. It is prohibited to reproduce, to store in a computer system or to transfer this publication or part of it in
any way. The copyright remains with all the rights with BÜRK MOBATIME GmbH, D-78026 VS-
Schwenningen and MOSER-BAER AG –CH 3454 Sumiswald / SWITZERLAND.

© MOBATIME 3 / 32 800697.09
Table of contents
1Description .....................................................................................................................................................5
2Assembly........................................................................................................................................................7
2.1 Single-sided clock ....................................................................................................................................7
2.2 Double-sided clock...................................................................................................................................7
2.3 Assembly diagram....................................................................................................................................8
2.3.1 ECO-DC.57 ......................................................................................................................................8
2.3.2 ECO-DC.100 ....................................................................................................................................8
2.4 Control elements......................................................................................................................................9
3MBL, MBLDCF and IRIG clock type operation..........................................................................................11
3.1 MBL type................................................................................................................................................11
3.2 MBLDCF type.........................................................................................................................................11
3.3 IRIG type................................................................................................................................................11
4NTP and PoE clock operation.....................................................................................................................12
4.1 Unicast mode .........................................................................................................................................12
4.1.1 Network parameters assignation by DHCPv4................................................................................13
4.1.2 Manual setting through setup menu...............................................................................................13
4.1.3 You can set only one IPv4 address of the NTP server via the clock menu ...................................13
4.1.4 Manual setting parameters over telnet:..........................................................................................13
4.1.5 Setting network parameters over DHCPv6 ....................................................................................14
4.1.6 Setting network parameters over autoconfiguration (SLAAC) .......................................................14
4.1.7 SNMP .............................................................................................................................................15
4.2 Multicast mode.......................................................................................................................................15
5WiFi clock operation....................................................................................................................................16
5.1 Setting via default MOBA-WIFI wireless network (Configure using)......................................................16
5.2 Setting via AP mode (Configure using)..................................................................................................16
5.3 Setting the network parameters using telnet..........................................................................................16
6Local time calculation .................................................................................................................................18
6.1 Basic setting –control according to source of synchronization .............................................................18
6.2 Calculation using MOBALine time zones...............................................................................................18
6.3 Calculation using Time-zone server MOBATIME ..................................................................................18
6.4 Calculation using time zone entries preconfigured by MOBA-NMS software........................................18
6.5 Calculation according to internal time zone table ..................................................................................19
7The clock menu table ..................................................................................................................................20
7.1 Submenu IPv6 adres..............................................................................................................................21
8Control and configuration of the clock using pushbuttons....................................................................22
8.1 Setting of time and date .........................................................................................................................22
8.2 Setup menu for the setting of the clock parameters ..............................................................................22
8.2.1 Submenu for network services configuration .................................................................................23
8.2.2 Manual setting of the IPv4 address of the clock.............................................................................23
8.2.3 Manual setting of the IPv4 subnet mask ........................................................................................23
8.2.4 Manual setting of the default gateway IPv4 address......................................................................24
8.2.5 Submenu for setting the IPv4 multicast group address..................................................................24
8.2.6 Submenu for setting of the NTP unicast synchronization ..............................................................24
8.3 Submenu for displaying IPv6 addresses................................................................................................25
8.4 Parameter reset......................................................................................................................................25
9Update firmware of NTP and PoE version using TFTPD32 tool..............................................................26
10 Time zone table............................................................................................................................................27
11 Technical data..............................................................................................................................................29

© MOBATIME 4 / 32 800697.09
11.1 Standard design of the clock..................................................................................................................29
11.2 Voltage range and electric current consumption of the lines.................................................................29
12 Accessories and Maintenance....................................................................................................................30
12.1 Single sided clock...................................................................................................................................30
12.2 Double sided clock.................................................................................................................................30
12.3 Cleaning.................................................................................................................................................30

© MOBATIME 5 / 32 800697.09
1 Description
The Economy series covers low cost elegant and very slim digital clocks in 7 segment LED
technique for displaying time and date • The Economy series can be operated in 3 freely
selectable modes • Autonomous operation with internal quartz powered from mains • NTP
multicast or unicast synchronization Ethernet or WiFi network powered over PoE (compatible
IEEE 802.3af) or mains powered • Slave clock operation controlled by self-setting MOBALine
code, or optionally by DCF 77 code or by IRIG-B, mains powered • LED display in red, green,
pure green, blue, yellow or white colour • Single- or double-sided clock • Plastic case in black
color • Wall mounting for single sided clock • Ceiling suspension or wall bracket mounting for
double sided clock • Intended for indoor use
Display features
•Time display in four digits (HH:MM) or six digits (HH:MMSS or HH:MM:SS) format, either 12
or 24 hours format
•AM/PM indication for 12-hour time format according to HW version
•Date display in four digits (DD.MM.) or six digits (DD.MM.YY or DD.MM.YY) format
•7 segment LED with 57 or 100 mm digit height for a viewing distance up to 25 or 40 m
•Alternating display of time and date with adjustable time period
•Display available in the red,green, pure green, blue, yellow or white
•Sensor controlled automatic or manual adjustment of the display brightness
Mechanic
•Anti-reflection front cover made of plexiglass including a filter layer for best readability over
a wide viewing angle
•Elegant and slim clock frame, made of plastic in black color
•Single- or double-sided version for wall mounting, ceiling suspension or wall bracket
mounting
•Double sided version consist of two pieces single sided clock and suspender
•Easy installation and time-saving maintenance, hanging holes for wall mounting,
•Supporting element for distance from wall (can be removed to tilt the clock down)
•All connectors and state LED are accessible on the back side in the recess
•Push-buttons are accessible on the back side in the recess
•Protection degree IP 30
•Equipment protection class II (no PE connection, plastic case)
•Working temperature -5 to +55°C
Synchronization
•Autonomous operation with internal quartz time base with programmable, automatic
seasonal time change
•NTP multicast or unicast synchronization in Ethernet or unicast synchronization in WiFi
network powered over PoE or mains powered
•Slave clock operation with synchronization by self-setting MOBALine code, or optionally by
DCF 77 code or by IRIG-B, mains powered
•Precision 0.3 s/day at constant temperature –software trimming
•RTC backup with supercapacitor

© MOBATIME 6 / 32 800697.09
Configuration
•Setting of the clock parameters and time –date setting by means of push buttons
For PoE and NTP version only:
•IPv4 and IPv6 support
•DHCPv4, DHCPv6 / manual configuration of the clock parameters or setting over the telnet
•Private options of DHCPv4 and DHCPv6 string to easy configuration of clock parameters
when connected to LAN
For PoE, NTP and WiFi version only:
•Configuration / supervision by means of MOBA-NMS software or SNMP protocol
•Firmware update remotely through the network using the TFTP protocol
•Powered from mains with wide input voltage range 100-240 VAC, optionally from 24 VDC
or through PoE (except WiFi)

© MOBATIME 7 / 32 800697.09
2 Assembly
The connection to the 110/230 V AC power network can be done only by authorized personnel
with appropriate qualification and training.
The connection to the 110/230 VAC power network must be done in accord with the
requirements of the connection of the class II equipment.
Danger of electric shock after dismounting the back cover.
The connection to the 110/230 V AC power network should be carried out when the mains
power is off.
2.1 Single-sided clock
•Drill two anchoring holes into the wall, of a diameter adequate to accommodate
supplied wood-type screws with dowels. See the assembly diagram (chapter 2.3) for
appropriate hole spacing.
•Mount the hanging screws with the dowels to drilled holes in a way that the heads of
the screws are ca 3-5mm from the wall.
•Shorten all the incoming cables appropriately.
•Mount the wide 2-pin connector to the incoming powering cable.
•Mount the 2-pin connector to the synchronization signal cable or crimp the RJ45
modular connector to the incoming Ethernet cable.
•Connect all the interconnecting cables into the corresponding connectors in the
clock’s back side recess.
•Hang the clock to the hanging screws.
•If the clock has to be tilted down, cut the supporting element on the bottom of the
back side accordingly.
2.2 Double-sided clock
•The double-sided clock consists of two parts, one serving as the control module (this
one encompasses the terminals to connect powering voltage and synchronization
source), and the other serving as the display module (with the terminal for the
connection of interconnecting cable). Both clock parts are interconnected via a 10-
core flat cable. The clock suspension part is delivered separately.
•Drill four anchoring holes into the ceiling (or wall), of a diameter adequate to
accommodate supplied wood-type screws with dowels.
•Interlace the incoming cables through the suspension pipe. Fasten the ceiling
suspension (or the side console) to the ceiling (or the wall), using 4 wood screws of
5 mm dia.
•Interlace the incoming cables through the pipe insert on the anchoring plate Slip-on
the plate onto the suspension in a way that the screws fit into the upper groove on
the pipe insert. Fix the connection by tightening the screw using an Allen key.
•Hang the display part of the clock to one side of the anchoring plate.
•Shorten all the incoming cables appropriately.
•Mount the wide 2-pin connector to the incoming powering cable.
•Mount the 2-pin connector to the synchronization signal cable or crimp the RJ45
modular connector to the incoming Ethernet cable.
•Connect all the interconnecting cables into the corresponding connectors in the
clock’s back side recess.
•Hang the clock to the hanging screws.
•If the clock has to be tilted down, cut the supporting element on the bottom of the
back side accordingly.

© MOBATIME 8 / 32 800697.09
•Loosen the screws on the suspension using the Allen key, and lift the clock into the
suspension in a way that the screws fit into the lower groove on the pipe insert.
Secure the attachment by tightening the screw using the Allen key.
Note: during the disassembly first withdraw the clock and suspend the suspension on
the upper groove at the pipe insert.
2.3 Assembly diagram
2.3.1 ECO-DC.57
Single sided clock back side´s recess
Double sided clock
ceiling suspension mounting wall bracket mounting
2.3.2 ECO-DC.100
Single sided clock back side´s recess
Double sided clock

© MOBATIME 9 / 32 800697.09
ceiling suspension mounting wall bracket mounting
2.4 Control elements
Ethernet connector (PoE, NTP only) RJ45 10BaseT/100TX (IEEE 802.3)
auto-negotiation
PoE version compatible with
IEEE 802.3af
Line-IN connector (MBL, MBLDCF,
IRIG only) time signal input: MOBALine, DCF 77
or IRIG-B
Power supply connector (not in PoE) powering 100 - 240 VAC voltage
DISP2 connector connection of the second side (for
double sided clock)
PB1, PB2 control pushbuttons
LINK LED (PoE, NTP only) Ethernet link connected
ACTIVITY LED (PoE, NTP only) Ethernet connection activity
STATE LED state indication
POWER LED indication of power applied

© MOBATIME 10 / 32 800697.09
AM /PM indication

© MOBATIME 11 / 32 800697.09
3 MBL, MBLDCF and IRIG clock type operation
3.1 MBL type
•Connect the MOBALine signal to the two-pin input signal connector and the mains
voltage to the two-pin power connector
•Set the menu items according to following P3:A, P4:A, P6:A
•After the connection, the time and date are adjusted automatically following the
receipt of valid time information. The synchronization takes 6-15 seconds.
•It is possible to use the MOBALine time zone function, the zone is selected by menu
item P5.
The colon permanently lit during the time display signalizes the synchronized clock.
See the chapter 8 for further description of parameter setting.
3.2 MBLDCF type
•Connect the MOBALine or Active DCF 77 signal to the two-pin input signal
connector and the mains voltage to the two-pin power connector
•Set the menu items according to following P3:A, P4:A, P6:A
•After the connection, the time and date are adjusted automatically following the
receipt of valid time information. The synchronization takes 6-15 seconds for
MOBALine or 3-5 minutes for Active DCF 77.
•For MOBALine it is possible to use the time zone function, the zone is selected by
menu item P5.
The colon permanently lit during the time display signalizes the synchronized clock.
See the chapter 8 for further description of parameter setting.
3.3 IRIG type
•Connect the IRIG signal to the two-pin input signal connector and the mains voltage
to the two-pin power connector
•DCF-FSK, IRIG-B Standard, IRIG-B 123, IRIG-B DIEM, AFNOR A, AFNOR C
variants of time signal are supported
•Set the menu items according to following P3:A, P4:A, P6:A
•After the connection, the time and date are adjusted automatically following the
receipt of valid time information. The synchronization takes 6-15 seconds.
The colon permanently lit during the time display signalizes the synchronized clock.
See the chapter 8 for further description of parameter setting.

© MOBATIME 12 / 32 800697.09
4 NTP and PoE clock operation
Clocks support IPv4 and IPv6 protocols. You can disable individual protocols by setting
parameter P7. The default clock setting allows both protocols at the same time (P7: 0).
For IPv4 mode, DHCPv4 is enabled by default (option P8: 3).
IPv6 mode allows up to 4 different priority IP addresses in downward order:
•DHCPv6
•manually configured IP address (fix)
•autoconfiguration. (SLAAC / RA)
•local address link
By setting parameter P14, you can disable DHCPv6 and/or auto-configuration (SLAAC).
For IPv6 mode, DHCPv6 and autoconfiguration (SLAAC) are enabled by default (P14: 3).
Calculate of Link Local Address:
fe80 :: 2 [2. octet MAC]: [3. octet MAC] ff: fe [4. octet MAC]: [5. octet MAC] [6. octet MAC]
Example: MAC: 00: 16:91 : 12:34:56
IPv6: fe80 ::216:91ff: fe12:3456
4.1 Unicast mode
The clock is synchronized to UTC (Universal Time Coordinated) from a NTP server (up
to four NTP server IPv4/IPv6 addresses configurable) and must have assigned its own
IPv4/IPv6 address. The clock requests in defined intervals the actual time from the
NTP server. If the server is not available, the clock tries to contact the other defined
servers in cyclic way until the valid response from the NTP server is received.
This operating mode supports the monitoring and configuration of the movement via
the network connection by means of the Telnet, SNMP or the MOBA-NMS software
tool. For supervision and configuration with MOBA-NMS the clock’s IPv4/IPv6 address
can be used or the multicast group address having last octet cleared to zero
(presuming the multicast is not disabled).
It is necessary to set appropriate time-zone for correct displaying of local time and date
–see the chapter 6 for details.
Default network parameters:
IP mode
IPv4 / IPv6
IPv4 address
0.0.0.0
IPv4 subnet mask
0.0.0.0
IPv4 default gateway
0.0.0.0
NTP server address 1
0.0.0.0 / 0:0:0:0:0:0:0:0
NTP server address 2
0.0.0.0 / 0:0:0:0:0:0:0:0
NTP server address 3
0.0.0.0 / 0:0:0:0:0:0:0:0
NTP server address 4
0.0.0.0 / 0:0:0:0:0:0:0:0
NTP request time [s]
10
DNS server
0.0.0.0 / 0:0:0:0:0:0:0:0
SNMP manager 1
0.0.0.0 / 0:0:0:0:0:0:0:0
SNMP manager 2
0.0.0.0 / 0:0:0:0:0:0:0:0
multicast config address
239.192.54.1 / FF38::EFC0:3601
(FF38::239.192.54.1)
alive notification interval [min]
30

© MOBATIME 13 / 32 800697.09
configuration port number
65532
time zone client port number
65534
DHCPv4
enabled
SNMP
enabled
Multicast support
enabled
Telnet
enabled
IPv6 fix address / prefix
0:0:0:0:0:0:0:0/ 64
IPv6 link local address
fe80::2[2. octet MAC]:[3. octet MAC]ff:fe[4. octet
MAC]:
[5. octet MAC][6. octet MAC]
DHCPv6
enabled
autokonfigurace (SLAAC)
enabled
4.1.1 Network parameters assignation by DHCPv4
IP clock mode must be set to IPv4 mode (P7: 0/1).The menu item P8 must be set to
value 3(default). Network parameters are automatically obtained from a DHCPv4
server.
The following DHCP options will be evaluated automatically:
[50] IP address
[3] Gateway address
[1] Subnet mask
[42] list of up to four NTP server addresses / time zone server address (usually the
same as the NTP server address)
[6] DNS servers
[26] MTU
[60] Vendor Class ID
[43] or [224] Additional options (refer to document BE-800793)
The network administrator must configure the DHCPv4 options accordingly.
Assigned parameters can be checked in the submenu of items P9 to P11.
.
4.1.2 Manual setting through setup menu
The menu item P8 must be set to value 2.
•See chapter 8.2.2 for setting the clock’s IPv4 address in the item P9 submenu
•See chapter 8.2.3 for setting the subnet mask in the item P10 submenu
•See chapter 8.2.4 for setting the gateway in the item P11 submenu
•See chapter 8.2.5 for setting the multicast group address in the item P12 submenu
•See chapter 8.2.6 for setting the unicast NTP server address in the item P13
submenu.
4.1.3 You can set only one IPv4 address of the NTP server via the clock menu
4.1.4 Manual setting parameters over telnet:
•connect to the clock and make the needed settings by windows command
telnet <IP address>
example: telnet 192.168.0.190
•request for entering the password appears after connection (default password is
718084)
•the information about software and hardware version followed by the MAC address
is displayed after entering the correct password
•inserted commands must be confirmed by pushing the Enter key, use the
Backspace key for correcting typing errors
•command help or ?displays help with a command list

© MOBATIME 14 / 32 800697.09
•command reset resets the clock (changes are written to Flash)
•command conf -p displays current parameters from setup menu
•command conf -n displays current network parameters
•command conf -? displays help for command conf parameters
•example: conf -i 192.168.0.190 sets the clock’s IP address to 192.168.0.190
•it is necessary to end telnet connection by command exit
Windows 7 note: The telnet is not activated in Windows 7 by default. For activating it go
to the “Control Panel” in “Start menu”, click on “Programs and Features”, click on “Turn
Windows features on or off” and find the “Telnet Client” check box in the window
“Windows Features”. Allow the system to install the appropriate files –this should take
only a few seconds. The administrator rights are necessary for this operation.
Hyperterminal note: The Hyperterminal application can be used as an alternative to
telnet. It is necessary to activate the “Send line ends with line feeds” and “Echo typed
characters locally” in the Properties -> Settings -> ASCII setup window.
4.1.5 Setting network parameters over DHCPv6
IP clock mode must be set to IPv6 mode (P7: 0/2). Menu item P14 must be set to 3
(default setting) or 2. The network parameters are automatically retrieved from the
DHCPv6 server.
The following DHCPv6 options can be processed:
[3] non-temporary addresses
[16] vendor class
[17] vendor options
[23] DNS servers
[24] DNS domain
[25] Identity Association for Prefix Delegation
[31] SNTP servers
The network administrator must set the DHCPv6 options on the server accordingly.
Assigned parameters can be checked in the P14submenu.
4.1.6 Setting network parameters over autoconfiguration (SLAAC)
IP clock mode must be set to IPv6 mode (P7: 0/2). Menu item P14 must be set to 3
(default setting) or 1.
The following SLAAC options can be processed:
[3] Prefix info
[5] MTU
[24] Route info
[25] RDNSS
The network administrator must set the SLAAC options on the server accordingly.
Assigned parameters can be checked in the P14 submenu

© MOBATIME 15 / 32 800697.09
4.1.7 SNMP
The ECO-DC clock supports SNMP version 2c notifications and parameter reading and
setting by means of SNMP GET and SET commands. This allows to integrate the clock
to a network management system. The ECO-DC (SNMP agent) can send alarm
notifications and alive notifications to a SNMP manager. The IP address of the SNMP
manager can be provided to the clock by DHCP, Telnet, SNMP or the MOBA-NMS.
The structure of supported parameters is defined in a MIB file (refer to document TE-
800728 or BE-800793 for details). In addition the clock supports the “system” node
parameters defined by MIB-2 (RFC-1213)
Alarm notifications are asynchronous messages and are used to inform the manager
about the appearance / disappearance of alarms.
Alive notifications are sent out periodically to report availability and state of the clock.
The interval time can be configured.
SNMP community strings:
read community
romobatime
read / write community
rwmobatime
notification (trap) community
trapmobatime
4.2 Multicast mode
The clock is synchronized to UTC (Universal Time Coordinated) from a NTP server.
The clock receives NTP multicast packets transmitted by the NTP server in a specified
time cycle. This type of synchronization requires no clock’s own IP address and is
therefore suitable for an easy commissioning of the large systems of slave clocks.
Further this mode supports monitoring and parameter configuration by means of
MOBA-NMS software.
For supervision and configuration with MOBA-NMS the multicast group address can be
used or the multicast group address having last octet cleared to zero.
The Multicast operating mode signifies only a minimum amount of configuration work
for a network administrator.
It is necessary to set appropriate time-zone for correct displaying of local time and date
–see the chapter 6 for details.
Default network parameters:
IPv4 multicast group address
239.192.54.1
IPv4 multicast config address
239.192.54.0
IPv6 multicast group address
FF38::EFC0:3601
(FF38::239.192.54.1)
IPv6 multicast config address
FF38::EFC0:3600
(FF38::239.192.54.0)
configuration port number
65532
time zone client port number
65534
The menu item P8 must be set to value 1. See chapter 8.2.5 for setting the multicast
group address in the item P12 submenu.

© MOBATIME 16 / 32 800697.09
5 WiFi clock operation
In the item P15,choose if the clock will behave like WiFi AP, or will connect to wireless
network set by user, where network parameters could be set manually (telnet, clock menu) or
automatically (DHCP). If the DHCPv4 is used, the parameters assigned by the server can be
checked in the items P9 to P11 submenus.
5.1 Setting via default MOBA-WIFI wireless network (Configure using)
•set your WiFi router to the following default wireless network parameters
Net name (SSID): MOBA-WIFI
Used coding: WPA/WPA2
Coding key: hgfedcba
DHCP v4: allowed
Clock’s IP address: display using item P9 submenu
•set value 2in item P15 in the main MENU
•display clock’s IP address in the item P9 submenu
•connect your computer to the default MOBA-WIFI wireless network
•connect clock using telnet, see chap. 5.3.
5.2 Setting via AP mode (Configure using)
•set value 3in item P15 in the main MENU
•connect your computer to the MOBAxxxxxx wireless network with the following
parameters:
Net name (SSID): MOBAxxxxxx
(where xxxxxx represents certain octets WiFi clock’s
MAC address)
Used coding: WPA2
Coding key: password
DHCPv4: allowed
Clock’s IP address: 192.168.2.1
•connect clock using telnet, see chap. 5.3.
5.3 Setting the network parameters using telnet
•connnect clock via windows command <IP adresa>
e.g. telnet 192.168.2.1
•the request for the password appears (initial password is 718084)
•the software and hardware version displays if password entering was successful
•inserted commands can be sent off using Enter key, the Backspace key serves for
correction of the typing errors
•command help or ?displays help with command’s list
•command reset resets the clock (setting modifications are written to data flash)
•command conf –p displays the current setting of the menu parameters
•command conf –ndisplays the current network parameters, MAC address and
wireless network parameters
•command conf –?displays help for the command conf parameters
•command wifi-n displays the wireless network setting
•command wifi-? displays helpfor wifi parameters
•it is necessary to end telnet by command exit

© MOBATIME 17 / 32 800697.09
Example of setting network parameters using telnet –WPA and DHCPv4:
•command wifi –s mobatime set network name (SSID) of new wireless network
•command wifi –w 7 set version of used coding on PEAP
•command wifi–u eapuser set user name for EAP authentication to “eapuser”
•command wifi –p abcdefg set password for EAP authentication
•command conf –u1 pool.ntp.org set IP address of NTP server on
“pool.ntp.org”. Both NTP name and IP address can be use.
•command conf –p8:03 set the clock for connecting to the new initiated wireless
network with DHCPv4 report
•command exit ends telnet and writes changes into Flash
Example of setting network parameters using telnet –WPA2 with static IP
•command wifi –s mobatime set network name (SSID) of new wireless network
•command wifi –w 4 set version of used coding on WPA2 for new wireless network
•command wifi –p abcdefg set encryption key for new wireless network
•command wifi –m 1 set wifi mode to user-defined wireless network
•command conf –u1 pool.ntp.org set IP address of NTP server on
“pool.ntp.org”. Both NTP name and IP address can be use.
•command conf –p8:02 set the clock for connecting to the new initiated wireless
with manually set network parameters
•command conf –i 192.168.0.254 set clock’s IP address to 192.168.0.254
•command conf –s 255.255.255.0 set clock’s subnet mask on 255.255.255.0
•command conf –g 192.168.0.254 set clock’s default gateway 192.168.0.254
•command exit ends telnet and writes changes into Flash

© MOBATIME 18 / 32 800697.09
6 Local time calculation
6.1 Basic setting –control according to source of synchronization
P4
A
Time zone is carried over from the source of synchronization
P5
0
Neither MOBALine time zone nor time zone server are used
P6
A
Display time and date according to source of synchronization incl.
daylight saving time
This setting is suitable for digital clocks controlled by a master clock as slave clocks in
a time distribution system using the MOBALine, Active DCF 77 or IRIG time signal. An
internal time zone table is not used.
6.2 Calculation using MOBALine time zones
P4
A
Time zone is carried over from the source of synchronization. The
UTC time calculation is based on the MOBALine information.
P5
1 - 20
Selection of the MOBALine time zone
P6
A
Display time and date according to chosen MOBALine time zone,
incl. daylight saving time
This setting is suitable for digital clocks controlled by a master clock as MOBALine
slave clocks in a time distribution system with the possibility to display different
MOBALine time zones.
6.3 Calculation using Time-zone server MOBATIME
P4
A
NTP protocol uses UTC time zone
P5
1 - 15
Selection of the time zone server time zone
P6
A
Display time and date according to chosen time zone server time
zone, incl. daylight saving time
This setting is suitable for NTP and PoE digital clocks controlled by MOBATIME NTP
servers, which support the time zone server functionality.
6.4 Calculation using time zone entries preconfigured by MOBA-NMS
software
P4
A
NTP protocol uses UTC time zone
P5
0
No time zone server is used
P6
U1-U7
Display time and date according to chosen preconfigured time zone
entry, incl. daylight saving time
This setting is suitable for NTP and PoE digital clocks, where several user defined time
zone entries should be used. The time zone entries are preconfigured by means of the
MOBA-NMS software.

© MOBATIME 19 / 32 800697.09
6.5 Calculation according to internal time zone table
P4
0 –64
According to time zone in which source of synchronization works
P5
0
Neither MOBALine time zone nor time zone server are used
P6
0 –64,
U
Display time and date by calculation from the UTC time according
to chosen time zone, incl. daylight saving time
This setting is suitable for autonomous digital clocks or in cases when the displayed
time is needed from another time zone than provided by the synchronization source.
Displayed time and date calculation is based on the internal time zone table, see
chapter 10 –current definition. This setting is useful also for the NTP synchronization
when no time zone server is available.
If you want to use the zone outside the internal time zone table, follow the “Custom
Time Zone” appendix.

© MOBATIME 20 / 32 800697.09
7 The clock menu table
Program item
Function
Scope of the values (default values are printed in bold)
0
Display brightness
1-30, A (automatic)
P1
Time display
format
24h
24-hour time format
12h
12-hour time format, **AM/PM indication according to HW version
P2
Display mode
1-3
1
continuous display of time
2
continuous display of date
3
display sequence: time 6 sec, date 3 sec
U*
time constants set up by user, in seconds for each specific displayed data
(available for Option E only)
P3
Source of
synchronization
A(automatically)
P4
Time zone of
synchronization
source
0 - 64, A (automatically)
P5
Time zone for
MOBALine or time
zone server
MOBATIME
1-20, 0(off) –for MOBALine synchronization
or
1-15, 0(off) –for NTP synchronization
P6
Time zone of
displayed time
and date
0 - 64, A (automatically), U* (user time zone, see chap. 6.5)
U1-U7 (preconfigured time zone entry by MOBA-NMS)
P7
IP mode
0
IPv4 / IPv6
1
IPv4
2
IPv6
P8
Network operation
mode IPv4
1*
multicast (without IP address)
2*
unicast –network param. defined manually
3*
unicast –network param. defined by DHCPv4
P9
IP addresss
IP*
edit network parameters in manual setting mode or display parameters
assigned by DHCP
P10
Subnet mask
Su*
P11
Gateway
Gg*
P12
Multicast address
Mc*
setting multicast group address
P13
Unicast NTP addr.
Uc*
setting NTP unicast server address
P14
Network operation
mode IPv6
0*
none
1*
autoconfiguration (SLAAC)
2*
DHCPv6
3*
both
P15
WiFi mode
1
user-defined wireless network
2
default wireless network: MOBA-WIFI
3
AP mode
P16
Clock address for IR
remote control (available
for Option E only)
1-99
P17
IR controller autolock
(available for Option E
only)
1-60, U (autolock is off)
Verze SW
r_._ (např.: r6.17)
•possibility to enter the submenu
•Items P7 to P14 available in NTP, PoE and WiFi variants only
•Item P15 available in WiFi variant only
•Items P16 to P17 available for option E variants only