Mobatime METRO User manual

© MOBATIME TE-801005.01
Mounting instructions
METRO Outdoor clocks, round, single- and double-sided
Before installation of the clock please read the manual carefully.

© MOBATIME 2 / 12 801005.01
References to the Instruction Manual
1. The information in this Instruction Manual can be changed at any time without previous
notice.
2. This Instruction Manual has been composed with utmost care, in order to explain all details
in respect of the operation of the product. Should you, nevertheless, have questions or
discover errors in this Manual, please contact us.
3. We do not answer for direct or indirect damages, which could occur, when using this
Manual
4. Please read the instructions carefully and start the setting-up of the product, only once you
have correctly understood all information for the installation and of the operation.
5. The installation must only be carried out by skilled staff.
6. It is prohibited to reproduce, to store in a computer system or to transfer this publication in
a way or another, even part of it. The copyright remains with all the rights with BÜRK
MOBATIME GmbH, D-78026 VS-Schwenningen and MOSER-BAER SA – CH 3454
Sumiswald / SWITZERLAND.

© MOBATIME 3 / 12 801005.01
Table of contents Page
1 Mounting instructions .....................................................................................................4
1.1 Building department / authority permit.........................................................................4
1.2 General rules...............................................................................................................4
1.3 Handling reference......................................................................................................4
1.4 Internal Connections...................................................................................................4
1.5 External Connections..................................................................................................4
1.6 Open the clock............................................................................................................5
1.7 Exchange of movement and dial.................................................................................6
1.8 Close the clock............................................................................................................6
2 Mounting types ................................................................................................................7
2.1 Wall mounting E (Mounting type zz = 00)....................................................................7
2.2 Wall bracket WA (Mounting type zz = 10).................................................................8
2.3 Ceiling bracket DA (Mounting type zz = 20).............................................................8
2.4 Central post ZM (Mounting type zz = 40)...................................................................9
2.5 Lateral mounting to round post KRL (Mounting type zz = 30).................................9
2.6 Lateral mounting to square post KVL (Mounting type zz = 31)................................9

© MOBATIME 4 / 12 801005.01
1 Mounting instructions
1.1 Building department / authority permit
If necessary a building department / authority permit should be requested before mounting.
1.2 General rules
The mains supply for the clock must be installed only by a licensed electrician.
While the national installation regulations must be adhered.
Please provide a cable with a wire cross section of maximum 1.5 mm2.
The clock is not equipped with a mains plug. An all-pole disconnecting device and a fuse for
movement and lighting power supply must be provided in the on-site supply.
The fuses should be chosen according to the power consumption of the device.
For all maintenance and cabling work, the clock has to be separated from mains.
For safety reasons avoid to look directly into the LEDs.
1.3 Handling reference
1. The clock should be transported upright in its original packaging and must be stored dry.
2. Clean the cover glas with wet (lether-) cloth.
3. Never use solvents, aerosol or organic cleaning products.
4. The housing is to treat with standard cleaning agents.
1.4 Internal Connections
The internal wiring is made in the factory. It’s important not to modify the internal wiring.
1.5 External Connections
Dismantle the insulation of the connecting wires on a length of 8 – 9 mm and insert the wires up to the
isolation in the terminal. The spring terminal can be opened with a screw driver size 0.
Phase and neutral wire must be kept together close to the terminal using a cable tie.

© MOBATIME 5 / 12 801005.01
1.6 Open the clock
1. Unscrew the 3 screws of the glass ring, pull of the glass ring with the glass and deposit it carefully.
2. Untighten and turn the dial fixation flaps. Carefully pull the dial together with the movement out from
clock housing und disconnect the electrical terminals from the clock movement.
3. Deposit the dial with the movement and hands carefully.
Dial fixation flap
Fixation screws for glass mounting ring

© MOBATIME 6 / 12 801005.01
1.7 Exchange of movement and dial
1. Open the clock according to chapter 1.6
2. Before you exchange the dial, be sure that the hands show 12:00 position.
Check movement manual to set the hands to 12:00 position (DIP switch 1 = ON for 190 series
movements).
3. Loosen the Allen screw for the second- and minute hand and remove the hands from the axis.
4. Carefully remove the hour hand from the axis (clench bushing).
5. Use the special wrench to loosen the central nut of the movement and remove it from the shaft.
6. Fix the movement into the new dial (or the new movement into the existing dial) – connectors of the
movement must be at 6:00 position (buttom side) – and tighten the central nut with a torque of 4.5 Nm.
7. Connect the timesignal with the movement and check the correct time. Don’t forget to switch off the
12:00 position command at the movement (e.g. 190 series movements: DIP switch 1 = OFF).
8. Close the clock according to chapter 1.8.
1.8 Close the clock
1. Connect the electrical terminal(s) to the movement (time signal, power).
2. Put the dial to the correct position.
3. Turn the dial fixation flaps and tighten all four screws.
4. Pull the glass ring with the glass carefully over the housing frame and fix the ring with the 3 screws.
Check, that the cables do not affect the clock illumination with shadows on the dials.

© MOBATIME 7 / 12 801005.01
2 Mounting types
Nominal-Single-sided (E)
Type Double-sided (WA, DA, KRL, KVL, ZM) Type
50cm MTv.50.R1.www.xxx.y.zz MTv.50.R2.www.xxx.y.zz
60cm MTv.60.R1.www.xxx.y.zz MTv.60.R2.www.xxx.y.zz
80cm MTv.80.R1.www.xxx.y.zz MTv.80.R2.www.xxx.y.zz
Legend: v = Illumination (0 = no illumination, 2 = LED illumination)
www = Movement code, see document TE-800800 und TE-801006
xxx = Dial: 100: with MOBATIME logo, 101: without logo
y = Cover glass (1 = Mineral glass, 2 = Security glass, 3 = Polycarbonate glass)
zz = Mounting types: 00 = Wall mounting (single-sided, E)
10 = Wall mounting bracket (WA)
20 = Ceiling mounting bracket (DA)
30 = Side pole mounting, round Ø 133 (KRL)
31 = Side pole mounting, square 150 x 150 (KVL)
40 = Cantral post
2.1 Wall mounting E (Mounting type zz = 00)
The electrical cables can be inserted through the two grommets in the back wall of the clock.
Before the mounting, all connection cables has to be separated from mains!
After inserting the cables, fix the clock with the 3 screws (M10) to the wall, using the lugs outside of the
case.
Nominal-A B C D
50cm 566 176 160 594
60cm 666 176 180 694
80cm 866 176 180 894

© MOBATIME 8 / 12 801005.01
2.2 Wall bracket WA (Mounting type zz = 10)
The electrical cables can be inserted through the
mounting bracket (cable entry in the middle with
Ø 85 mm).
Before the mounting, all connection cables has to
be separated from mains!
Drill the holes according to the dimenstion drawing of
the flange and prepare them with dowels. Set four "set
screws" into the dowels. Insert the cables through the
bracket into the clock and fix the clock with 4 washers
and 4 nuts.
Flange
2.3 Ceiling bracket DA (Mounting type zz = 20)
The electrical cables can be inserted through the
mounting bracket (cable entry in the middle with
Ø 85 mm).
Before the mounting, all connection cables has to
be separated from mains!
Drill the holes according to the dimenstion drawing of
the flange and prepare them with dowels. Set four
"set screws" into the dowels. Insert the cables through
the bracket into the clock and fix the clock with 4
washers and 4 nuts.
Flange
Nominal -A B
50 566 150
60 666 150
80 866 150
Nominal -A B
50 566 150
60 666 150
80 866 150

© MOBATIME 9 / 12 801005.01
2.4 Central post ZM (Mounting type zz = 40)
Prepare the mast with a suitable fundament. For the
dimension of the fundament and the pole, the wind force
has to be taken into consideration. The electrical cables
has to be inserted through the pole.
Before the mounting, all connection cables has to be
separated from mains!

Nominal -ABmin. Bmax. C
50cm 566 40 76 90
60cm 666 40 76 90
80cm 866 60 102 130
2.5 Lateral mounting to round post KRL
(Mounting type zz = 30)
The electrical cables has to be inserted through the
pole.
Before the mounting, all connection cables has to
be separated from mains!
The fixation to the round pole can be done with the
clamping fixture and the 4 screws with nuts.
For standard pole dimension: 133.5 mm
Other dimensions on request.
2.6 Lateral mounting to square post KVL
(Mounting type zz = 31)
The electrical cables has to be inserted through the
pole.
Before the mounting, all connection cables has to
be separated from mains!
The fixation to the square pole can be done with the
clamping fixture and the 4 screws with nuts.
For standard pole dimension: 150 mm
Other dimensions on request.
Nominal -A B
50 566 150
60 666 150
80 866 150

© MOBATIME 10 / 12 801005.01