Mobileye EyeNET User manual

Mobileye 8 Connect
EyeNET User Manual v0.3

Page 2 of 12 | EyeNET User Manual v0.3
2
MOBILEYE, AN INTEL COMPANY
WWW.MOBILEYE.COM
M
obileye
8 Connect
|
February 2021
EyeNET User Manual 0.3
Table of Contents
TABLE OF CONTENTS 2
1. INTRODUCTION 3
2. EYENET COMPONENTS OVERVIEW 3
2.1 E
YE
NET C
OMPONENTS
O
VERVIEW
3
3. MOBILEYE 8 CONNECTION DESCRIPTION 4
3.1 E
YE
NET C
ONNECTION
L
AYOUT
D
ESCRIPTION
4
4. CONNECTION SCHEME 5
5. TECHNICAL SPECIFICATION 6
6. TECHNICAL SPECIFICATION 7
7. TROUBLESHOOTING 12

Page 3 of 12 | EyeNET User Manual v0.3
3
MOBILEYE, AN INTEL COMPANY
WWW.MOBILEYE.COM
M
obileye
8 Connect
|
February 2021
EyeNET User Manual 0.3
1. Introduction
Mobileye EyeNET adapter is a RGMII to Ethernet interface.
It is used for installation & calibration of the Mobileye 8 Connect systems.
Mobileye 8 Connect service port uses a RGMII interface (Reduced Gigabit Media-
Independent Interface) for faster & reliable data transfer rate.
The Ethernet port of the EyeNET provides a universal and very common connection method
for the end-user.
The EyeNET Support up to 1Gbit/s transfer rate
2. EyeNET Components Overview
The EyeNET (p/n EYENET0001) adapter composed of the following elements:
 EyeNET – Ethernet service port interface
 EyeNET short flex flat cable x2
 Ethernet cable
2.1 EyeNET Components Overview
description
P/N
EyeNET main unit ASY000355
2 X EyeNET cable BRD000350
Ethernet cable CAB000260

Page 4 of 12 | EyeNET User Manual v0.3
4
MOBILEYE, AN INTEL COMPANY
WWW.MOBILEYE.COM
M
obileye
8 Connect
|
February 2021
EyeNET User Manual 0.3
3. Mobileye 8 Connection Description
The following paragraphs describes in detail the function of the cables and connections shown
below:
3.1 EyeNET Connection Layout Description
Layout
description
function
view
CONF
N/A
RST
N/A
LED
communication status
RGMI port
communication
Ethernet port
communication
Reset switch
Octopus
N/A
SPI
N/A
The Mobileye 8 service port Male connector (P2) is used for connection with the Mobileye
EyeNet cable female connector labeled “xxx” (J5).
Wire Name Wire Color Connector Connect to
EyeNet cable
Black
XX
-
Male
Mobileye 8 service port
EyeNet
main unit
Black
XX
–
Female
EyeNet interface`s connector labeled
"XXX"
EyeNET Ethernet port
Gray
RJ45
Laptop Ethernet port

Page 5 of 12 | EyeNET User Manual v0.3
5
MOBILEYE, AN INTEL COMPANY
WWW.MOBILEYE.COM
M
obileye
8 Connect
|
February 2021
EyeNET User Manual 0.3
4. Connection Scheme

Page 6 of 12 | EyeNET User Manual v0.3
6
MOBILEYE, AN INTEL COMPANY
WWW.MOBILEYE.COM
M
obileye
8 Connect
|
February 2021
EyeNET User Manual 0.3
5. Technical Specification
Property
Description
EyeNET short cable length 12cm
Ethernet cable length 1 Meter
Ethernet cable type CAT5 / CAT6
Bit rate 1Gbps
Dimensions (W*L*H)
60.5mm X 91mm X 27mm
Housing
Black plastic
Weight
120 grams
Temperature range
N/A

Page 7 of 12 | EyeNET User Manual v0.3
7
MOBILEYE, AN INTEL COMPANY
WWW.MOBILEYE.COM
M
obileye
8 Connect
|
February 2021
EyeNET User Manual 0.3
6. Technical Specification
Please follow the below steps to configure the Ethernet adapter (either the build-in LAN
port or USB to LAN adapter)
1. Click Start, and in the search field, type View network connections
2. Press the right click on Local Area Connection (ASIX AX88179 USB 3.0 to Gigabit
Ethernet Adapter) and press on Properties

Page 8 of 12 | EyeNET User Manual v0.3
8
MOBILEYE, AN INTEL COMPANY
WWW.MOBILEYE.COM
M
obileye
8 Connect
|
February 2021
EyeNET User Manual 0.3
3. In the window "Local Area Connections Properties" uncheck all the [Check Box]
except: Client for Microsoft Network and Internet Protocol Version 4
4. When completing step 4 above, press on the Configure button
5. After pressing Configure a new Window will Open, Go to Advanced Tab

Page 9 of 12 | EyeNET User Manual v0.3
9
MOBILEYE, AN INTEL COMPANY
WWW.MOBILEYE.COM
M
obileye
8 Connect
|
February 2021
EyeNET User Manual 0.3
6. in the Advanced Tab Search for the following parameters and change them
accordingly to the following settings:
6.1 Speed Duplex – and change the Value to 1.0 Gbps Full Duplex
6.2 search Wake on Magic Packet - and change the Value to Disabled

Page 10 of 12 | EyeNET User Manual v0.3
10
MOBILEYE, AN INTEL COMPANY
WWW.MOBILEYE.COM
M
obileye
8 Connect
|
February 2021
EyeNET User Manual 0.3
6.3 search Receive Buffers - and change the Value to 2048
6.4 search Transmit Buffers - and change the Value to 2048

Page 11 of 12 | EyeNET User Manual v0.3
11
MOBILEYE, AN INTEL COMPANY
WWW.MOBILEYE.COM
M
obileye
8 Connect
|
February 2021
EyeNET User Manual 0.3
6.5 search Wake on pattern match - and change the Value to Disabled
7. go to Power Management Tab and Uncheck the Allow the computer to turn off
this device to save power
8. Press on Ok Button

Page 12 of 12 | EyeNET User Manual v0.3
12
MOBILEYE, AN INTEL COMPANY
WWW.MOBILEYE.COM
M
obileye
8 Connect
|
February 2021
EyeNET User Manual 0.3
7. Troubleshooting
In some cases when using of a USB to CAN adapter result a video delay in the calibration
step, please connect Mobileye EyeNET directly to the build-in LAN port (if exist).
If not, try to change USB port. If the problem consists, try to replace the adapter.