Mocka Eclipse User manual

Eclipse Cot
1
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Thank you for your purchase.
Ensure the cot is placed at a reasonable distance from curtains, blinds, heaters
and power points. Keep all medications, string, elastic, small toys or small items,
such as money, out of reach from any position in the cot.
Assembly
Care must be taken when attaching sides. Do not over-tighten screws as this can
cause damage to the cot.
Care and Maintenance
Regularly check all screws for tightness or damage that could render the cot
unsafe. To clean - use a damp cloth, avoiding the use of detergents or abrasives.
Recommended mattress size
This cot has been manufactured for use with a mattress which measures 1300mm
long x 690mm wide x 100mm in thickness. The width and length are specified
because it is important that gaps between the mattress and the sides and ends
of the cot will not exceed 40mm. This is to minimize the risk of a child’s limb
becoming caught in the gap. The thickness of the mattress has been specified to
ensure that the depth of the cot is greater than 500mm with the mattress base in
the lower position to minimize the risk of a child climbing or falling out of the cot.
Hardware Supplied
B
A
x1
Allen key
x14
screw
Please follow the manufacturer’s assembly instructions in detail
to ensure the safety features of the cot are not compromised.
WARNING: TO PREVENT FALLS, THE MATTRESSBASE
OF THIS COT SHOULD BE ADJUSTED TO THE LOWEST
POSITION BEFORE THE CHILD CAN SIT UP
Side Panel
Cot Mattress Base
End Panel

12
Eclipse Cot
2
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
1
1
1
1
2
3
Attach panels [1] to panel [2] and secure with 4 x screws (A). Tighten
with an Allen Key (B).
Attach panel [3] to panels [1] and secure with4x Screws (A). Tighten
with an Allen Key (B).
A
B
A
A
A
A
A
A
A
A

3
3
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Eclipse Cot
4
A
A
A
A
A
A
4
1
1
Attach panel [4] to panels [1] and secure with 4 x screws (A). Tighten
with an Allen Key (B). Regularly check all screws are suitably
tightened. Place the correct size mattress into the cot before use. To
clean use a damp cloth, avoiding the use of detergents or abrasives.
Rotate the cot on its side and attach 2 x screws (A) to panel (3). Tighten
with an Allen Key (B). Once assembled lift furniture into place, do not
drag. You’re done, enjoy!
3
3
A
B

5
4
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Eclipse Cot
1
1A
A
A
A
3
OPTIONAL/ MATTRESS HEIGHT ADJUSTMENT (please keep these
instructions handy for future reference)
To adjust mattress base settings, remove small plastic plugs. This will
require a small amount of force, please note these are not screws and
cannot be screwed out. You will need a screwdriver/ that fits into the
centre hole and possibly a hammer, or similar, to gently tap the end
until the plug pops out.
Repeat steps 2, 3 and 4 by removing the side panel and moving the
base to corresponding holes. Securely attach again in the adjusted
position.