modway Abeyance EEI -1182 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
EEI -1182 ABEYANCE OFFICE DESK
Hardware:
Component:
A Bolt M8x60mm x2
B Bolt M8x40mm x4
C Bolt M8x30mm x4
H Allen Wrench x1
1 Glass Top x1 2 Drawer Box x2
3 Leg x2 4 Central Rail x1
Flat Washer x24
D Bolt M8x10mm x16
E Washer x2
Plastic Cap x2
F
G
Thank you for purchasing the MODWAY ABEYANCE OFFICE DESK！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the desk, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
EEI -1182 ABEYANCE OFFICE DESK
Ax2 Ex2 Gx2 Hx1
STEP 1:
Place one of the Legs (3) to the Central Rail (4) as shown.
Please make sure that the concave surface of each Washer (E) faces to the head of each Bolt (A) when connecting.
Attach them by using Bolts (A) and Washers (E) through the pre-drilled holes on the Central Rail (4) and the same Leg (3) .
Tighten Bolts (A) with the Allen Wrench (H). Then cover the Plastic Cap (G) to the head of Bolt (A) as shown.
Repeat the same steps for assembling the other Leg (3) to the Central Rail (4).
Hardware & Tool required
STEP 2:
Dx16 Fx16 Hx1 Hardware & Tool required
Please put the Glass Top (1) upside down on a flat and smooth surface as shown .
Attach the assembled Central Rail (4),Legs (3) into the bottom of Glass Top (1) by using Bolts (D) and Flat Washers (F).
Use the Allen Wrench (H) to tighten the Bolts (4) clockwise until secure.
Notice：
Please make sure that the concave
surface of each Washer (E) faces to
the head of each Bolts (A) when connecting.

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
EEI -1182 ABEYANCE OFFICE DESK
STEP 3:
In order to properly attach the Drawer Box(2) to the side of the Legs (3), take out the extra space before leg. It will be neces-
sary to remove the two drawers from the Drawer Box (2). Please follow the following steps for drawer removal.
A, Open the drawer fully.
B, Locate the black quick disconnect levers on the right and left-hand slides.
C, Simultaneously press the quick disconnect levers while pulling out the drawer. As shown, the right-hand level is pressed
down, while the left-hand lever releases by pulling up.
STEP 4:
Bx4 Cx4 Fx8 Hx1 Hardware & Tool required
Carefully turn over the assembled desk.
Attach the Drawer Box (2) without drawers to one of Leg (3) by using Bolts (C) and Flat Washers (F) through the pre-
drilled holes on the inside of the right side panel of the Drawer Box (2) and one of Leg (3).
Do not fully tighten the Bolts (C) at this time.
Attach the Drawer Box (2) to the Central Rail (5) by using Bolts (B) and Flat Washers (F).
Use the Allen Wrench (H) to tighten Bolts (B) and Bolts (C) clockwise until secure.
Repeat the same steps for assembling the second Drawer Box (2) to the other leg (3).
Right-Hand Slide:
Press lever down
Left-Hand Slide:
Pull lever up

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
EEI -1182 ABEYANCE OFFICE DESK
Assembly is completed. The desk is ready to enjoy now!
STEP 5:
In order to return the two drawers into each Drawer Box (2).
A, Align drawer with drawer slides.
B, Move silver metal carrier fully forward in slide.
C, Gently push drawer into the drawer box.
Silver Metal Carrier Align drawer with drawer slides. Push drawer into
the Drawer Box (2) until clicking sound is heard
and slides are locked together