modway EEI-2275 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 3
EEI-2275 SWING CHAIR
Hardware:
Component:
A
F Spring x1
Thank you for purchasing the MODWAY SWING CHAIR！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approx assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that has been provided.
6.Please keep all fitting out of reach of children.
5
2
1
G Spring Holder x1
J Open Wrench x1
H Allen Wrench x1
Bolt/Nut M10x55mm x1
B Bolt/Nut M10x60mm x4
C Bolt/Nut M10x20mm x3
D Leveler x10
E Screw Set M6x30mm x2
1 Left Base x1
4 Upper Stand x1
2 Right Base x1 3 Lower Stand x1
5 Basket Frame x1
6 3
4
6 Cushion x1

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 3
EEI-2275 SWING CHAIR
STEP 1:
Ax1 Bx4 Cx3 Dx10 Ex2 Fx1 Gx1 Hx1 Jx1
Hardware & Tool required
Please put all chair parts on a carpeted or padded area.
Find hardware package in the box packing Base (1/2) & Stand (3/4).
Place left Base (1) to Right Base (2) as shown.
Secure the back of base by using 3 sets of Bolts/Nuts (C).
Secure the front of base by using 2 sets of Screw Set (E).
Use Allen Wrench (H) and Open Wrench (J) to tighten Bolts/Nuts (C) and Screw Sets (E) clockwise until secure.
Secure 10 pieces of Leveler (D) into the bottom of assembled Base as shown.
Insert Spring Holder (G) into the pre-drilled hole at the top of Upper Stand (4) as shown.
Hang Basket Frame (5) to Upper Stand (4) by using 1 piece of Spring (F) as shown.
Place Cushion (6) to Basket Frame (5) as shown.
STEP 4:
STEP 3:
Insert Upper Stand (4) into Lower Stand (3) as shown.
Secure by using 1 set of Bolt/Nut (A) .
Use Allen Wrench (H) and Open Wrench (J) to tighten Bolt/Nut (A) clockwise until secure.
STEP 2:
Attach Lower Stand (3) to the assembled Base as shown.
Secure the back of base by using 4 sets of Bolts/Nuts (B).
Use Allen Wrench (H) and Open Wrench (J) to tighten Bolts/Nuts (B) clockwise until secure.

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 3
EEI-2275 SWING CHAIR
2
3
F
STEP 2
Assembly is completed. The swing chair is ready to enjoy now!
1
4
5
D
STEP 3
STEP 4
G
A
B
Maximum Weight: 120 KG
B B B
D
D
D
D
D
D
STEP 1
C
C
A
B
B
B
B
D D
D
C
E E
E
E
6