modway EEI –3040 User manual

EEI–3040 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com Page 1of 6
Thank you for purchasing the MODWAY OFFICE CHAIR.
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
Hardware:
A. Bolt M6x20mm x 4
B. Bolt M6x40mm x 4
C. Flat Washer M6 x 4
D.
E. Allen Wrench x1
Component:
1 Base x1 2 Cylinder Column x1 3 Control Mechanism x1
4 Seat x1 5 Back Frame x1 6 Castor x5 7 Foot Ring x1
1
6
7
3
4
5
6
6
6
6

EEI–3040 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com Page 2of 6
STEP 1:
Please put Base (1) on a carpeted or padded surface.
Insert 1 piece of Castor (6) into the Base (1) as shown by hand. Repeat the same steps for the remaining 4
pieces of Castors (6).
STEP 2:
Carefully turn over the assembled base from step 1.
Insert the bottom end of Cylinder Column (2) into the assembled Base (1) as shown.
6
1
6 6
6
6
1
2
2
1

EEI–3040 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com Page 3of 6
STEP 3:
Insert the Foot Ring (7) into the assembled Cylinder Column (2) as shown.
Please note the orientation of the top of the Foot Ring (7).
STEP 4:
Insert the Foot Ring (7) into the assembled Cylinder Column (2) at your desired height, but at least one inch
from the top of the outer circle of Cylinder Column (2). Please follow the direction of the arrow as shown to
tighten the knobs by hand on the Foot Ring (7) so the Foot Ring (7) is fixed.
7
2
1
2
1
Bottom of the Foot Ring
2
1
Top of the Foot Ring
7
7
1 inch
1
2
7

EEI–3040 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com Page 4of 6
STEP 5:
Attach Back Frame (5) to the bottom of Seat (4) by using 4 pieces of Bolts (B) with 4 pieces of Flat Washers (C)
as shown. Tighten Bolts (B) by using Allen Wrench (D) as shown.
Hardware & Tools required
STEP 6:
Attach Control Mechanism (3) to the Seat (4) by using 4 pieces of Bolts (A) as shown.
Tighten Bolts (A) by using Allen Wrench (D) as shown.
Hardware & Tools required
B
C
D
x 1
x 4
x 4
4
5
B
D
C
4
5
A
D
3
A
x 1
x 4
D

EEI–3040 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com Page 5of 6
STEP 7:
Insert the bottom holes of Control Mechanism (3) into the top end of Cylinder Column (2) as shown.
STEP 8:
Use the handle of Control Mechanism (3) to adjust the height of the office chair.
5
4
2
3
1
3
2
7

EEI–3040 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com Page 6of 6
STEP 9:
If you need to lower down the height of the office chair.
Please do not place feet or other objects between the Seat (4) and the Foot Ring (7).
STEP 10:
Assembly is complete. Your office chair is ready to be used now!
Do not place
feet or other objects
between the seat
and the foot ring.