modway EEI-3147 User manual

EEI-3147 DINING TABLE
Customer Service 609-256-9000︱www.modway.com
Page 1of 5
Thank you for purchasing the MODWAY Dining Table.
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the Dining Table, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 45 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
Hardware:
Components:
Bolt M8x30mm x16
Small Flat Washer x18
1. Leg x2 2. Handle x2 3. Top Panel x1 4. Upper Rail x2 5. Bottom Support x1
C.
Allen Wrench M8 x1
E.
Bolt M6x15mm x2
B.
A.
Big Flat Washer x4
D.
Allen Wrench M6 x1
F.
Big Nut x2
G.
Adjustable Spanner x1
H.
* Not include hardware bag

EEI-3147 DINING TABLE
Customer Service 609-256-9000︱www.modway.com
Page 2of 5
STEP 1:
1. Please put Top Panel (3) upside down on a carpeted or padded surface.
2. Attach 1 piece of Leg (1) to the Top Panel (3) by using 8 pieces of Bolts (A) and 8 pieces of
Small Flat Washers (C) as shown.
3. Tighten Bolts (A) by using Allen Wrench (E) as shown. Don't tight Bolts (A) fully.
STEP 2:
Please insert Bottom Support (5) into the pre-drilled holes in Leg (1) with 1 piece of
Big Flat Washer (D) as shown.

EEI-3147 DINING TABLE
Customer Service 609-256-9000︱www.modway.com
Page 3of 5
STEP 3:
1. Repeat STEP 1 to assemble the other 1 piece of Leg (1) to Top Panel (3) as shown.
2. Attach 2 piece of Big Nuts (G) and 2 piece of Big Flat Washers (D) to the two ends of Bottom
Support (5) as shown.
3. Use Adjustable Spanner (H) to tighten Big Nuts (G) as shown. Don't tight Big Nuts (G) fully.
STEP 4:
1. Please insert 2 pieces of Upper Rails (4) into the pre-drilled holes on Legs (1) by the convex slot as shown
by two adults.
2. When Legs (1),Top Panel (3),Upper Rails (4) and Bottom Support (5) are fixed, please fully tighten all
Big Nut (G) and Bolt (A).

EEI-3147 DINING TABLE
Customer Service 609-256-9000︱www.modway.com
Page 4of 5
STEP 5:
Carefully turn over the assembled Dining Table by at least four adults.
STEP 6
1. Please remove the plastic cover as shown with Figure 1.
2. Please insert 1 piece of Handle (2) into Leg (1) by the convex slot as shown.
3. Use Allen Wrench (F) to tighten 1 piece of Bolt (B) and Small Flat Washer (C) clockwise as shown.
4. Repeat the same way to assemble the other Handle (2) to other Leg (1).
Note: Twirling the Handle (2) can adjust the height of the Top Panel (3).

EEI-3147 DINING TABLE
Customer Service 609-256-9000︱www.modway.com
Page 5of 5
Assembly is complete. Your dining table is ready to enjoy now!