modway EEI-3860 User manual

Customer Service 908-368-1025︱Page 1 of 10
EEI-3860 Cabinet
Thank you for purchasing the MODWAY CABINET!
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 60 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture are fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
www.modway.com
A)
Ø 6 x 35 mm x18
F)
86 x 52 x 11 mm x 4
B)
Ø 15 mm x20
C)
x 26
D)
Ø 8 x 30 mm x 40
E)
x 4
K)
L 4
x 4
G)
x 2
H)
x 6
I)
4.5 x 12.5 mm
x 1
J)
M 7 x 50 mm
L)
67 x 67 mm x 4
M)
Ø 8 mm x 2
x 1
Screwdriver (Not Include)
Cambolt/Metal
Hinge/Metal
Camlock Big/Metal Dowel Big/Wood Shelf Support/Metal
Cambolt/Metal
Bracket/Metal
Screw/Metal
Screw/Metal
Key/Metal Buffer/Rubber
Hardware :
Cabinet,
Ø 6 x 32 mm
Foam Pad/Spons
25 x 25 x 2 mm

Customer Service 908-368-1025︱Page 2 of 10
5Shelf Back Panel x1
1Bottom Panel x1 2Left Side Panel x1
6Front Panel x1
3Right Side Panel x1
7Top Back Rail x1
4Adjustable Shelf Panel x1
8Middle Back Rail x1
9Front&Back Leg Apron x2 10 Leg Apron Side Rail x2 11 Middle Front Rail x1 12 Left Wooden Door x1
13 Right Wooden Door x1
Components:
www.modway.com
EEI-3860 Cabinet
1
2
3
4
5
67
8
9
9
10
10
11
12
13

Customer Service 908-368-1025︱Page 3 of 10
Bx4 Hardware required. Screwdriver not included
STEP 1:
STEP 2:
www.modway.com
Ax4 Cx12 Hardware required. Screwdriver not included
Mx1
9
10
C
A
Refer to Step 9
10
9
B
B9
EEI-3860 Cabinet
10
A
C
C
C
C
C
B
B
1.1- Lay flat both of the Components #9, Properly insert and slowly screw in the Cambolt (A) to
the lower portion of the pre-drilled holes at both ends of the Leg Apron.
1.2- Insert 2pcs of Wooden Dowel to the pre-drilled holes on both of the Front & Back Leg Apron (9)
top edges, ensure each dowel inserted is in the inner side of the pre-drilled hole.
1.3- Insert 4pcs of Wooden Dowel to the pre-drilled holes on both of the Leg Apron Side Rail (10) ends
and top edges, ensure each dowel inserted is in the inner side of the pre-drilled hole.
2.1- Insert 4 pcs of Camlock (B) to
the designated pre-drilled holes.
Align the Leg Apron Side Rail (10)
with the already inserted
Wooden Dowel (C)
to the Front & Back Leg Apron (9)
Push the Leg Apron Side Rail (10)
and secure both
parts by tightening
the Camlock (B).
2.2 - Repeat step 2.1 to the other
side rail.
2.3 - Properly align the loose Front
& Back Leg Apron (9) to the
assembly completed in step 2.2,
and secured the rest of the
Camlock (B) to complete the Leg
Apron assembly.
Consist of 2 components.
This hole
To assemble the leg Apron
Leg Apron Assembly
This hole
Mx1

Customer Service 908-368-1025︱Page 4 of 10
STEP 3:
STEP 4:
Gx2 Cx8 Hardware required. Screwdriver not included
www.modway.com
5
C
8
C
6
G
7
11
C
C
Dx8
Ax6 Cx6 Hardware required. Screwdriver not included
Dx8
2
D
C
C
A
C
C
A
3
EEI-3860 Cabinet
C
C
DD
D
D
CD
D
DD
C
G
A
A
A
A
C
C
D
DD
DD
DD
Carefully insert all hardwares as mentioned in the list to the respective components as shown.
Carefully insert all hardwares as mentioned in the list to the respective components as shown.
Pre-insert Dowel (C), Cambolt (G), & Screw (D)
Pre-insert Dowel (C), Cambolt (A), & Screw (D)
Mx1
Mx1

Customer Service 908-368-1025︱Page 5 of 10
STEP 5:
STEP 6:
www.modway.com
Bx3
B
7
8
11
2
Bx3
3
B
EEI-3860 Cabinet
Hardware required. Screwdriver not included
Hardware required. Screwdriver not included
B
B
B
B
Carefully insert the Camlock (B) to secure all Rails to the Left Side Panel (2).
Carefully insert the Camlock (B) to the pre-assembled Rails and carefully align the Right Side Panel (3)
and secure the Panel by tightening all inserted Camlocks (B) .
Securing Middle Back Rail (8), Top Back Rail (7), &Middle Front Rail (11) to the Left Side Panel (2)
Securing Middle Back Rail (8), Top Back Rail (7), &Middle Front Rail (11) to the Right Side Panel (3)
Mx1
Mx1

Customer Service 908-368-1025︱Page 6 of 10
STEP 7:
STEP 8:
Hx4 Hardware and Tool required
Ax8 Hardware required. Screwdriver not included
www.modway.com
1
I
H
I x1
A
EEI-3860 Cabinet
HH
H
A
A
A
A
A
A
A
7.1- Due to unstable structure,
carefully place the assembly from
STEP 6 with flat edges
(without dowel edges)
facing down onto flat surface.
7.2- Carefully align the Bottom Panel (1)
pre-drilled holes to the pre-assembled
Dowel on both of the
Side Panels (Left & Right) edges,
and secure it by tightening 4 nos
of Hex Screws (H) with the provided
Allen Key ( I ).
Ensure the Cambolt (A) is inserted
in the correct pre-drilled hole.
(The smaller pre-drilled hole).
Note: Ensure these pre-drilled holes are
facing upwards during assembly.
Carefully insert the Cambolt (A) to the pre-drilled holes.
Securing the Bottom Panel (1)
32
Note:Ensure these
pre-drilled facing
upwards during
assembly
3
2
Pre-inserted Cambolt (A) to anchor Leg Assembly (completed in Step 2)
Mx1

Customer Service 908-368-1025︱Page 7 of 10
STEP 9:
STEP 10:
www.modway.com
Bx8 Hardware required. Screwdriver not included
B
Bx2 Hardware required. Screwdriver not included
6
B
EEI-3860 Cabinet
B
B
B
B
B
Carefully place the Leg Apron
assembly to the cabinet structure and
tighten the Camlock (B) to secure
both structures.
10.1- From STEP 9, carefully turn the
Cabinet with Leg Apron upright.
10.2- Insert the Camlock (B) to both
Side Panels (2 & 3)
10.3- Align the Front Panel (6) with
protruded Cambolt (A) to the Side
Panel (2 & 3) edges.
10.4- Secure the Front Panel (6) by
tightening the Camlock (B).
Securing the Leg Apron completed in (Step2) to the main cabinet structure.
Pre-inserted Cambolt (A) to Anchor the Leg Assembly (completed in Step 2)
32
3
2
Mx1
Mx1

Customer Service 908-368-1025︱Page 8 of 10
STEP 11:
STEP 12:
www.modway.com
Kx4 Hardware required. Screwdriver not included
Hx2 I x Hardware required. Screwdriver not included
Ex4
4
I
5
H
4
E
EEI-3860 Cabinet
HE
E
E
11.1- Place the Corner Bracket (K)
at the protruded Screw (D) on
both Side Panel (2&3) and
Top Back Rail (7). Continue to
place it on another 3 corners.
11.2- Carefully tighten all
protruded Screws (D).
12.1- Align the protruded dowel on Shelf Back Panel (5)
edge to the pre-drilled holes on Shelf Panel (4)
and secure it by Hex Screw (H).
12.2- Insert the Shelf Support (E) to the desired height.
12.3- Carefully place the pre-drilled holes underneath
the Shelf Panel (4) to the inserted
Securing the Corner Bracket (K)
3
2
To assemble the Adjustable Shelf Panel (4) and Shelf Back Panel (5)
Shelf Support (E)
Mx1
Mx1
K

Customer Service 908-368-1025︱Page 9 of 10
STEP 13:
STEP 14:
Fx4 Dx8 Hardware required. Screwdriver not included
www.modway.com
Dx16 L x4 Hardware required. Screwdriver not included
J x2
EEI-3860 Cabinet
D
13.1- Lay both door on flat surface.
13.2- Place the Hinge (F) on each of the pre-cut cup. ( 2 cups on each door).
13.3- Secure each Hinge (F) with 2 nos of Screws(D).
14.1- Carefully align each Door
(12/13) to the edge of the Side
Panel (2 & 3) and secure each
Hinge (F)with 4 nos of Screws (D)
14.2- Stick the Door Buffer (J )
to the top end of each door.
14.3- Place the Foam Pad (L) on
the cabinet top edge.
Securing the door hinges (F)
Securing the Left & Right Door (12&13)
Sold Separately
Mx1
Mx1
12
13
DD
F
DD
F
DD
F
DD
F
J
J
12
13
L
L
L
L

Customer Service 908-368-1025︱Page 10 of 10
STEP 15:
STEP 16:
www.modway.com
DETAIL HOLE FOR
WALL FIXING
Assemblyis complete and ready for sink installation.
EEI-3860 Cabinet
NOTE :
Hammer, fisher and screw
not included
15.1- Using spirit / water levelling tool, adjust the Cabinet level by adjusting the leg leveler.
15.2- Based on type of Wall structure, drill the holes and secure the Vanity Cabinet.
Securing the Vanity Cabinet (Professional Installer Required)