modway MOD-5569 User manual

5569/5570 QUEEN BED
H
I
J
Side Plastic Cover
Center Plastic Cover
×28
×14
×36
×5
70
11
1 Post-1 ×1
2 Post-2 ×1
3 Post-3 ×2
4 Side Rail ×2
5 Center Rail ×1
6 Stretcher ×3
7 Support Leg ×3
8 Cross Bar-1 ×2
9 Cross Bar-2 ×2
10 Connect Bar ×2
11 Headboard ×1
G
M6
12
12 Slat ×28
B
C
D
E
F
step-by-step
Approximately
have
and
3
3
4
4
6
5
6
6
7
9
10
10
9
8
8
M6 ×14
M6
M6
20
12
Flat Washer
QUEEN

569/5570 QUEEN BED
Insert the connector on the Cross Bar-1 (8) as shown then insert them into the Post-3 (3) into the
by using Bolts (A) and Allen Wrench (F) . corresponding holes on Cross Bar-1 (8)
Place Connect Bar (10) to the assembled Post-3 (3) by using Bolts (A) and Allen Wrench (F) as shown.
A
F
F
A
A
10
3
3
8
10
8
11
F
A
A
F
Insert the connector on the Cross Bar-1 (8) as shown then insert them into the Post-1 (1) & into the
by using Bolts (A) and Allen Wrench (F).corresponding holes on
Post-2 (2)
Cross Bar-1 (8)
Place Connect Bar (10) to the assembled Post-1 (1) and Post-2 (2) by using Bolts (A) and Allen Wrench (F) as shown.
Place Headboard (11) to the assembled Post-1 (1) and Post-2 (2) by using Bolts (D) and Allen Wrench (F)
as shown.
D
D
D
Adjust the height as you
need to choose the right
hole
and
and
8F
F
F
8G×4
G
G
&Flat Washer (G)

5569/5570 QUEEN BED
F
A
A
F
4
4
5
9
9
1
2
3
3
Insert the connector on the Cross Bar-2 (4) then insert them into the Post-2 (2) & into the
by using Bolts (A) and Allen Wrench (F). corresponding holes on
Post-3 (3)
Cross Bar-2 (9)
Place Side Rail (4) to the assembled Post-2 (2) and Post-3 (3) Bolts (A) and Allen Wrench (F) as shown.
Repeat the same steps for the remaining Post-1 (1) & Post-3 (3) & Cross Bar-2 (4).
20 F
Place Side Rail (4) to the assembled Stretcher (6) by using Bolts (C) & Nut (E)
and
Allen Wrench (F) &
as shown.
6
6
6
4
4
as shown and
F
F
E
E
C
C
8 F 8
by using
Place Center Rail (5) to the assembled Stretcher (6) by using Bolts (C) & Nut (E) and Allen Wrench (F)
as shown.
EH×1
H
H
C
Repeat the same steps for the remaining Post-1 (1) & Post-3 (3) & Cross Bar-2 (9).
10
10
Place Center Rail (5) to the assembled by using Bolts (A) and Allen Wrench (F)as shown.Connect Bar (10)
Repeat above for the other Side Rail (4).
5
F
G
G×2
& Flat Washer (G)
Open Wrench (H)
Open Wrench (H)

5569/5570 QUEEN BED
STEP 5
C
H
H
5
6
6
6
B×5 C×1 F×1 E×6 H×1
Insert 5 pieces of Bolt (B) into the 5 holes on Center Rail (5) to connect it with Support Leg (7) as shown.
Insert Bolt (C) into the holes on Center Rail (5) and Stretcher (6) to connect it with Support Leg (7) as shown.
Secure the above 6 pieces of Bolts (B&C) with Nuts (E) & from the bottom of Support Leg (7) at same time.
Use Allen Wrench (F) and Open Wrench (H) to tighten all Bolts (B&C) and Nuts (E) & until secure.
Kx28
Jx14
I
I
K
12
12
Insert 2 pieces of Side Plastic Cover (I) into each end of 2 pieces of Slat (12) as shown.
Insert the other end of the Slats (12) into 1 piece of Center Plastic Cover (J) as shown.
Insert the assembled Side Plastic Covers (I) into the corresponding holes on Side Rail (4),and the assembled Center
Plastic Cover (J) into the corresponding holes on Center Rail (5) as shown.
Repeat the same steps for the remaining 28 pieces Slat (12)..
STEP 6:
F
B
B
E
B
E
E
Hardware & Tool required
7
7
7
F
G×6
G
G
G
G
Flat Washer (G)
Flat Washer (G)