modway Viola EEI-3373 User manual

Thank you for purchasing the MODWAY SOFA!
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step instructions.
2. Owing to the size and weight of the Sofa, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 25 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save tools that have been provided.
6. Please keep all fitting out of reach of children.
Hardware:
1JCBC BOLT M6 x 70 2 PCS
2JCBB BOLT M8 x 30 12PCS
3 JCBB BOLT M8 x 45 7 PCS
4FLAT WASHER M6 2 PCS
5SPRING WASHER M6 2 PCS
6FLAT WASHER M8 19PCS
7SPRING WASHER M8 19 PCS
8WOOD DOWEL M10 X 30mm 6 PCS
9ALLEN KEY (BALL SHAPE) M4 1 PC
10 ALLEN KEY (BALL SHAPE) M5 1 PC
Component:
A. BACK
B. SEAT
C. ARM
D. FRONT LEG
E. BACK LEG
EEI - 3373 SOFA
x 1
x 1
x 2
x 2
x 2
A
B
C
C
D
E
11 WOOD SCREW M4 x 32mm 4 PCS
Page 1 of 4
Customer Service 609-256-9000 www.modway.com

STEP 1
EEI - 3373 SOFA
1.1 Fit the Wood Dowel (8) into the pre-drilled hole of the Back (A) .
1.2 Insert and secure the Back (A) to the Arm (C) using 1 piece of JCBC Bolt (1), 1 piece of Flat Washer (4), and 1 piece of Spring
Washer (5). Use Allen Key (9) to tighten. (Note: Do not fully tighten until all bolts are secure). Repeat steps for the other side of the Arm.
1. JCBC BOLT M6 x 70 x 2pcs 5. SPRING WASHER M6 x 2pcs 4. FLAT WASHER M6 x 2pcs 9. ALLEN KEY (BALL SHAPE) M4 x 1pc
8. WOOD DOWEL M10 x 30mm X 2PCS OR
TOOLS REQUIRED FOR ASSEMBLY
Rubber Mallet Plastic Tip Hammer
914
5
x 2
1.1
1.2
A
C
C8
Page 2 of 4
Customer Service 609-256-9000 www.modway.com

STEP 2
10
3
7
6
10 376
EEI - 3373 SOFA
x 4
x 3
2.1 Fit the Wood Dowel (8) into the pre-drilled hole of the Seat (B) .
2.2 Insert and secure the Seat (B) to the Back (A) & Arm (C) using 7 piece of JCBC Bolt (3), 7 piece of Flat Washer (6) , and 7 piece of
Spring Washer (7). Use Allen Key (10) to tighten. (Note : Finish step 2 : Please tighten bolt at step 1.2 )
3. JCBC BOLT M6 x 70 x 7pcs 7. SPRING WASHER M6 x 7pcs 6. FLAT WASHER M6 x 7pcs 10. ALLEN KEY (BALL SHAPE) M4 x 1pc
8. WOOD DOWEL M10 x 30mm X 4PCS OR
TOOLS REQUIRED FOR ASSEMBLY
Rubber Mallet Plastic Tip Hammer
2.1
2.2 2.3
8
B
Page 3 of 4
Customer Service 609-256-9000 www.modway.com

STEP 4
4.1 Carefully position the assembled Sofa to the desired location by four adults.
Assembly is complete. The Sofa is ready to use now!
NOTE: Hardware may loosen over time. Periodically check that all connections are tight.
EEI - 3373 SOFA
STEP 3
2. JCBB BOLT M8 x 30 x 12pcs 7. SPRING WASHER M8 x 12pcs 6. FLAT WASHER M8 x 12pcs 10. ALLEN KEY (BALL SHAPE) M5 x 1pc
11. WOOD SCREW M4 x 32 x 4pcs
x 2
7
10
E6
3.2
2
3.3 x 2
11
E
E
E
D
LEFT
RIGHT
D
10 276
3.1 x 2
3.1 Insert and secure 1 piece of Front Leg (D) using 3 pieces of JCBB Bolt (2), 3 pieces of Flat Washer (6) and 3 pieces of Spring
Washer (7). Use Allen Key (10) to tighten. Repeat steps for the other side of Front Leg (D) .
3.2 Insert and secure 1 piece of Back Leg (E) using 3 pieces of JCBB Bolt (2), 3 pieces of Flat Washer (6) and 3 pieces of Spring
Washer (7) and 2 pieces of Wood Screw (11) . Use Allen Key (10) and Screwdriver to tighten. Repeat steps for the other side of Back
Leg (E)
TOOLS REQUIRED FOR ASSEMBLY
Page 4 of 4
Customer Service 609-256-9000 www.modway.com