modway Vivify EEI-2852 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
EEI –2852 DESK
Thank you for purchasing the MODWAY DESK！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the desk, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
Hardware:
1
Long Bolt M6x40mm x4
2
6 Allen Wrench M4 x1
3
Component:
A Desk Top x1
C
Leg x4
B
Top Frame x1
Medium Bolt M6x20mm x4
Short Bolt I M6x15mm x12
C
D Side Rail x2
E
Back Rail x1
4
Short Bolt II M6x12mm x4
5 Castor x4
A
B
B
B
B
E
E
D

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
EEI –2852 DESK
STEP 1:
STEP 2:
Put Top Frame (A) upside down on a carpeted or padded surface.
Place 4 pieces of Leg (B) to Top Frame (A) as shown.
Insert 8 pieces of Short Bolt I (1) into the pre-drilled holes on Top Frame (A) through the pre-drilled holes on Legs (B).
Use Allen Wrench (6) to tighten Short Bolts I (1). Do not fully tighten Short Bolts I (1) at this step.
Hardware & Tools required
Hardware & Tools required
1x8 6x1
3
B
1x4 6x1 2x4 4x4
Put Bottom Rails (E) and Back Rail (D) to the assembled Top Frame (A) and Legs (B) as shown.
Insert 4 pieces of Long Bolt (2) into the pre-drilled holes on Back Rail (D) through the pre-drilled holes on Bottom Rail (E).
Insert 4 pieces of Medium Bolt (4) into the pre-drilled holes on Side Rails (E) and Back Rail (D) through the pre-drilled holes
on Legs (B).
Insert 4 pieces of Short Bolt I (1) into the pre-drilled holes on Side Rails (E) and Back Rail (D) through the pre-drilled holes
on Legs (B).
Use Allen Wrench (6) to tighten all the Bolts (1&2&4). Do not fully tighten all the Bolts (1&2&4) at this step.
E
D
B
2
B
B
B
B
2
C C
6
1 1
1
1
1
1
1
1
A
B
B
B
B
E
D E
E
D
4
1
2
2
4
1
1 2
2
6
2
1
4
1
4
A
4

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
EEI –2852 DESK
STEP 3:
STEP 4:
Tighten 4 pieces of Castor (5) into the bottom of assembled Legs (B) by hand clockwise until secure as shown.
Hardware & Tools required
Hardware & Tools required
5x4
D
A
5
3x4 6x1
Put Desk Top (C) upside down on a carpeted or padded surface.
Place the assembled Top Frame (A), Legs (B), Side Rail (E), and Back Rail (D) to Desk Top (C) as shown.
Insert 4 pieces of Short Bolt II (3) into the pre-drilled holes on Desk Top (C) through the pre-drilled holes on Top Frame (A).
Use Allen Wrench (6) to tighten all the Bolts (1&2&3&4) clockwise until secure at this step.
C
A
E
B
D
5
5
5
E
E
B
B
B
B
E
3
6
3
3
3
B
B
B

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
EEI –2852 DESK
STEP 5:
Carefully turn over the assembled desk.
Assembly is complete. Your desk is ready to be used now!